What is the minimum platform that supports GETVPN over DMVPN?
I have been looking around cisco website but couldn't find a document with the supported platforms.
We have branch offices with Cisco 861 routers and i would like to know if we could use GETVPN with these routers.
Does ASR 1000 Series support DMVPN Hub, and Key Server in GETVPN.
View 2 Replies View RelatedI need to connect site to MPLS provider and run Cisco GETVPN.Problem:I have been browsing Cisco Feature Navigator Tool and to my surprise when I enter "platform:3745" I can't find an image compatible with GET VPN. there is no workaround (image) I can run GET VPN on 3745? I need IP routing (BGP, OSPF) as well.
View 1 Replies View RelatedI've done some tests and it seems that a 7201 supports GETVPN without a VAM, but in the design guide it states that this is needed.Is this needed as the 7201 documentation states that it performs IPSEC encryption in hardware without a VAM.
View 3 Replies View RelatedWhere's the ideal place to put the KS? My current setup is 1 KS, 19 GM. The KS sits BEHIND a GM, so all other GMs have to come through one GM to get to KS.Now, I have purchased two dedicated KS routers. I configured one today, and placed it right on my WAN. My WAN is a L2 Ethernet domain, so i just provisioned a switch port in the WAN vlan, and away we go. I copied RSA keys over from the current KS, configured redundancy and the two hooked up, saw each other and it seems to be good to go. For the ACL, I put in an exclustion for my two KS to talk to each other:
deny ip host 192.168.250.40 host 192.168.250.41 (Old IP, New IP)
deny ip host 192.168.250.41 host 192.168.250.40.
I used a test router and pointed it to the new KS, it registered without a hitch... HOWEVER about two hours later (my 7200 second timeout) I lost ALL my branches. My 18 other GM were still pointed to the OLD IP only, they didnt have the second IP configured yet. In a hurry, I quickly disabled the redundancy configuration on the old KS and had to go to each GM and do a 'clear crypto gdoi' on each one to get them to re-register. There were no log messages about not being able to rekey, no log messages about dropped peerings, nothing. Once I did that, everything returned to normal.
The Question I have...
Would having configured the redundant KS caused this problem? Would having one KS behind a GM and the other Coop KS in the WAN make a difference?
Relevant config from existing KS, 2801:
crypto gdoi group GETVPN_GROUP
identity number 1234
server local
rekey retransmit 60 number 2
rekey authentication mypubkey rsa GETVPN_KEYS
[Code]...
We have 6 WAN routers connected through ISP MPLS cloud , we need to implement GET VPN between these WAN routers.We have 2 Key servers (1800 routers) , and the WAN routers will act as Group Members (6 GMs)
The attached configuration files are for working configuration for typical GETVPN (crypto map applied on WAN interface)
In Key server configuration , the crypto isakmp command is using the WAN interface IP address of each WAN router (172.16.x.x) , and since that the KS routers are connected to local backbone (VSS) , they should be able to reach 172.16.X.X , and therefore the subnet 172.16.X.X is advertised to the local network (check GM configuration file under eigrp - redist connected )
This is what our customer want to avoid ! they do not want 172.16.X.X to be advertised to the local network .I know It is possible in GETVPN configuration to configure ,the crypto isakmp command to use loopback address's of the WAN routers instead of the WAN IP , but in this case the crypto map must be applied to the loopback address , and this requires all traffic to be encrypted and decrypted to go through the loopback interfaces on all WAN routers .
i was wondering what is the best solution for this case , I though to use the below config on the GM's
in LMS (4.1) installing guide, table 'Software and Hardware Requirements for Soft Appliance', it is stated Memory and CPURequirement:
• 4 GB, 2 virtual CPU (< = 500 devices)Host CPU Core clock speed:
• Minimum 2.26 GHz Minimum Virtual CPU Reservations: Number of recommended virtual CPUs x 2.26 GHz:
• 4520 MHz (< = 500 devices)
I have HP server with 6 core CPU 2.0GHz - does it mean it does not meet the minimum system requirements (2.26Ghz)? Will I be able to go pass the installation?
Got a question regarding 2921 modules. Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?
As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
I am confused about the cisco docs:What is the minimum WLC/WCS version to support WISM2 controllers ?
The datasheet of WISM2 says "minimum 7.0.116.0"
URL
However the release notes of 7.0.116.0 do not mention the WISM2 module ?
URL
The release notes of 7.0.220.0 do mention the WISM2:
URL
I need to be absolutely sure as there are other software dependencies between 7.0.116.0 and 7.0.220 (regarding required MSE and Aeroscout versions).
With WCS 7.0.172.0 and WLC 7.0.116.0, will we have WISM2 support ?
I configure two WIC-1DSU-T1-v2 interfaces with a T1 crossover cable. What are the mimimum configurations to do to communicate from LAN1 (int fa0/0 of one 1841 router) to LAN2 (int fa0/0 of the second 1841 router) ?
Do I need a routage protocole ? And if yes wich one ? Interne or externe (RIP or BGP) Or static route is enough ? Also, is that I should put a encapsulation, like ppp ? Is it neccessary on a point to point line ?
Finally what about the following commands, do I need it ?
service-module t1 clock source internal
service-module t1 timeslots 1-24 speed 64
service-module t1 framing esf
service-module t1 linecode b8zs
belkin n wireless router minimum coverage ?
View 1 Replies View Relatedwhat are the things needed in setting a cyber cafe with minimum of 5pcs eg the most most profitable model, fast.
View 10 Replies View RelatedWe have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport I would think I should have more, but have not had any issues with a few power outages
View 1 Replies View Relatedwhat should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
need an access point configured in the user minimum because I was looking and some had up to 49 LAP connections at the same time. I have a WLC 4402 VERSION 7.0.98
View 1 Replies View RelatedI'm running WCS 7.0 on a WLSE appliance. Lately WCS has produced the following alarm:WCS 150.3.101.7 does not meet the minimum hardware requirements for disk space. Available: '29'GB. Minimum requirement: '30'GB. I have old WCS versions (3, 4, 5 and 6) so could delete those but I'm wary in case I take out the data too.
View 2 Replies View Relatedgive me a link to where I can find the minimum code version for N55-M16UP expansion card for a Nexus 5k?
View 1 Replies View Related what is the minimun privilege level to assign at username account on ASA 5505 to grant the access with AnyConnect?
username ... privilege ?
I am looking to install 2 1552I outdoor AP's. I can't find what the minimum code version is on the WISM controller that supports this AP.I am running 7.0.98.0 on the WISM. Where can I find this information?
View 4 Replies View RelatedI want to know that what is the minimum acceptable size of preamble in ethernet frame. if it is less than 7 bytes before sfd begins , will the packet drop?
View 1 Replies View RelatedI want to "stack" a couple 300 series gigabit switches with fiber using a pair of MGBSX1 GBICs and a single LC to LC patch cable.Is there a minimum supported patch cable length in this configuration?
View 2 Replies View RelatedI want to know how much minimum power required for swicth catalyst 3750.I want to know cause in my building place, the power in unstable so it make my switch corrupt/damage even i add power consistancy....
How much amount power to the ups and ups to switch?
I'm currently in the process of evaluating potential equipment options for a Core Router/Switch that will be running BGP with several Tier 1 ISP's, the table download from each ISP will be full (300,000+ Routes). I was looking at a 6509-E with dual SUP720-3BXL supervisors but after reading the below link I'm a little concerned by the maximum routes table: [URL]
Do I have to go to the VS based 720 supervisor as a minimum to support full BGP on a 6509-E? Does any experience of the above switch + supervisor combination under a full BGP table, how well does it work? I'm looking at long term using this as a consolidated core (i.e. a VRF for the Global Internet routing table + a VRF for internal data center traffic, plus maybe some more shared VRF's).
Would I be better keeping a Core switch by itself and just buying edge routers to run BGP?
What is the minimum distance to be maintained while laying Power cable ( light and fan power points) and Data cable?
View 1 Replies View RelatedI am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.
I am using a single 12 MBit line.
We are looking to deploy ISE supporting 5000 devices and would like to use the Cisco UCS platform to host this. Looking at the spec required a C22 M3 would be sufficient; however we would also like to host some UC applications on the same server if resources allow.
Therefore we would like to deploy ISE on a C220 M3 server and connect the associated NIC to a DMZ. We would then like to deploy UC applications such as CUCM and CUPS on the same UCS server with a NIC attached to the internal network.
Also while the UC application would require a UC Foundation License (R-VMW-UC-FND5-K9) whould this also meet the requirements for ISE?
Is it possible to cisco 1941 security bundle router Support minimum of 2k of VLANs ID and shall support upto 60 vlans?
View 4 Replies View RelatedThere use to be Cisco 851 routers, but lately these routers are replaced with Cisco 861-K9 routers, and these 861 routers doesn't support DMVPN, instead 851 use to be.
Is there any license file we can upload in 861 router for DMVPN capability, if yes may i know the SKU # for that. We have some customers having 6-7 locations and they are planning to have 2 more locations, we implement already DMVPN in there network, if we go with the 87X or 88X router there price is almost double the price of 861.
I am doing a school research project in which I am setting up an OC-192 ring for a company (contract work through AT&T). I have chosen to use the Cisco ONS 15454 SONET MSPP as my platform. The company currently has locations in Chicago and Philadelphia and connects them through an OC-12C ATM connection and they are looking to add 2 gigabit ethernet connections.My question is what cards and parts will I need for the Cisco ONS 15454 SONET MSPP, and how much will everything cost? I have been searching the internet for components and prices and I have found it extremely difficult to find any information.
View 2 Replies View RelatedI currently have a 50Mbps Internet Connection provided by an ethernet handoff for hosting some webservers. We are looking at adding an additional 10Mbps Internetn connection and route BGP between the two. For the 50Mbps connection, i'm using a Cisco 2951 router. I also have another 2951 router to terminate the 10Mbps connection. Does these router have enough horsepower to fully route BGP?
View 1 Replies View RelatedIs there any way to auto migrate my 3030 VPN configuration to an ASA platform?
View 3 Replies View RelatedI want to select catalyst 3560G for my network. But IOS SLB need to be implemented in my network. I only know catalyst 6500 series can support this feature and i am not sure whether 3560G can support this feature. what platform and IOS version i need to implement IOS SLB?
View 1 Replies View RelatedA make one BOM and i just ask my self can we order on the one platform ( for example 5510-SEC-BUN-K9 ) SSL Essentials license ( this license is on the platform by default we buy 250 users ) and i need 50 Users license from them to be Premium.
Can i buy those two license on the same platform and is this will work ?
