Cisco :: Minimum Software To Support WISM2 WCS 7.0.172.0
Feb 23, 2012
I am confused about the cisco docs:What is the minimum WLC/WCS version to support WISM2 controllers ?
The datasheet of WISM2 says "minimum 7.0.116.0"
URL
However the release notes of 7.0.116.0 do not mention the WISM2 module ?
URL
The release notes of 7.0.220.0 do mention the WISM2:
URL
I need to be absolutely sure as there are other software dependencies between 7.0.116.0 and 7.0.220 (regarding required MSE and Aeroscout versions).
With WCS 7.0.172.0 and WLC 7.0.116.0, will we have WISM2 support ?
View 4 Replies
ADVERTISEMENT
Feb 15, 2012
I am looking to install 2 1552I outdoor AP's. I can't find what the minimum code version is on the WISM controller that supports this AP.I am running 7.0.98.0 on the WISM. Where can I find this information?
View 4 Replies
View Related
Nov 18, 2011
I'm currently in the process of evaluating potential equipment options for a Core Router/Switch that will be running BGP with several Tier 1 ISP's, the table download from each ISP will be full (300,000+ Routes). I was looking at a 6509-E with dual SUP720-3BXL supervisors but after reading the below link I'm a little concerned by the maximum routes table: [URL]
Do I have to go to the VS based 720 supervisor as a minimum to support full BGP on a 6509-E? Does any experience of the above switch + supervisor combination under a full BGP table, how well does it work? I'm looking at long term using this as a consolidated core (i.e. a VRF for the Global Internet routing table + a VRF for internal data center traffic, plus maybe some more shared VRF's).
Would I be better keeping a Core switch by itself and just buying edge routers to run BGP?
View 2 Replies
View Related
Dec 17, 2012
Is it possible to cisco 1941 security bundle router Support minimum of 2k of VLANs ID and shall support upto 60 vlans?
View 4 Replies
View Related
Sep 17, 2012
We have some new WISM2 running 7.0.116.0, but now we need to upgrade their license to suport 1000 APs. So I am looking at upgrading the software to 7.2.110.0. We are running WCS at the moment and got NCS with the new WISM2, so going to 7.3 and buying Prime Infrastructure is not an option at the moment, thus we are going for 7.2.
The thing is I can't seem to find much info about this upgrade. Is 7.0->7.2 a smooth upgrade? Do we need to do any configuration changes to the WISM2 or LAP1242? We are running H-REAP, will the change to FlexConnect be affected? I can't seem to find anything regarding requirements for 6500/SUP for running WISM2 7.2, do I need a certain software for that?
View 5 Replies
View Related
May 9, 2012
We have just installed lms 4.2 and are having problems collecting config and inventory from ws-svc-wism2-k9. The response from TAC was that this is not supported. And it also says this in
[URL]
Is this really the case ? Will there be released packeges to support this. It would be really useful if this was supported in lms4.2.
View 3 Replies
View Related
Mar 13, 2013
I have a question regarding WISM2 DP and licensing.
Suppose i have a WISM2 with 7.0, 500AP license today and i activate WISM2-DP by upgrading to 7.2,Do i get 500 AP capacity for free (total 1000AP) or do i get 250APs on each WISM2-blade ?
If i get 500APs for free, why is Cisco selling an expensive licensed 1000 AP WISM2 ? I better buy a single-plane 500AP-WISM2 and upgrade it myself then...50% profit.
Is this the same for a WISM2-300 (supporting 300 APs) ?When i activate WISM2-DP here, do i get an extra 300 AP or an extra 500 APs ? Or 150AP on each blade ?
View 7 Replies
View Related
Oct 11, 2011
I know the WiSM 2 is like the 5500 WLC regarding the fact that you do not need to configure an ap-manager interface for CAPWAP packets because by default the managment interface acts like an ap-manager interface.
Any major advantages or disadvantages by letting the default action occur?
View 2 Replies
View Related
Dec 19, 2012
I having an issue with WCS and the new code 7.4 on my WiSM2 blade. When I try to refresh configuration from/to controller it fails. I just upgraded from 7.01 and it worked before the upgrade.
Is this not supported?
I am able to change configuration from WCS to the WiSM2 and it works fine just cant copy config.
View 7 Replies
View Related
Jan 18, 2013
I have just been setting up a WISM2 in a test lab and for some reason the Supervisor is not creating a port channel on my 6500 as suggested in the WISM2 Deployment Guide. WISM2 is installed in an appropriate slot (according to same doco) and have attempted reset to factory defaults, removing and power cycling several times.
View 1 Replies
View Related
Jan 8, 2013
I have installed WiSM2 with ver 7.4 and Bonjour works great with instruction provided, But…… 2 problems. I cant get it to work on the same subnet. (odd since the whole problem was not able to work across subnets), More important the new Code function / password function on the airplay wont work. I get the code on the projector, but the ipad never pop up the login box it just errors out.
View 2 Replies
View Related
Dec 12, 2012
I am about to migrate WISM1 to WISM2, The image of WISM1 is 6.0.199.4 and the image of WISM2 is 7.2.111.3.
Do i need to upgrade WISM1 to 7.2.111.3 before i export the configuration and import it into WISM2? Or can i just export the configuration from WISM1 on 6.0.199.4 and import directly to WISM2 which is on 7.1.111.3?
View 2 Replies
View Related
Jan 28, 2013
I have purchased a new WiSM 2 and my catalyst 6509-E is failing to detect it. Here are the details of the switch:
1. supervisor engine: vs-s720-10g-3cxl
2. ios image: s72033-advipservicesk9_wan-mz.122-33.SXI10.bin
3.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 8 Intrusion Detection System WS-SVC-IDSM-2 SAD103501HP
2 4 FRU type (0x6003, 0x3B2(946)) WS-SVC-WISM2-K9 SAL1648T81L
[code]....
View 2 Replies
View Related
Apr 5, 2012
My company has been contracted to upgrade the 2 WiSM1 modules on a 6509 for a customer. The hardware isn't changing but the software is being upgraded to WiSM2. The cutsomer has HUNDREDS of AP's and dozens of VLANs and subnets (large municipality and school district).
Cisco SE's have been pushing the customer to purchase the WCS 7 software (they've been managing these Controllers independantly) stating there is no mechanism to upgrade WiSM1 configs to WiSM2. I am vaguely familiar with the cisco controllers but have little WiSM experience. So i feel like i'm working without a net here.
So,
1) Any way to migrate from 1 to 2 without the WCS and without having to reinvent the wheel?
2) How does the WCS make this transition easier? What does it do to the WiSM1 configs to make them WiSM2 compatable?
View 21 Replies
View Related
Apr 14, 2012
Just loaded the 7.2.103.0 software onto the brand new WiSM2. Going throught the options and have found that under the global parameters for 802.11a/n, 802.11b/g/n radios is now the "Maximum Allowed Clients" option. The allowed setting is from 1 - 200 clients.
Does that mean only 200 clients will be allowed to associate to the WLC on that radio at a maximum?
Doesn't seems to make sense... I have the 500 AP license on this WiSM2... I know this option used to be an optional setting under a WLAN in previous releases.
View 2 Replies
View Related
Apr 10, 2013
I have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.
View 1 Replies
View Related
Jun 27, 2012
I have a situation where a customer doesn't have the required power units installed in their 6500 for me to provision a WiSM2.They use a VSS pair with a single Sup720 in each. They have no intention of adding a second Sup to each chassis.
I need to justify why they can't use slot 6 (which has power reserved) if I am to get them to upgrade the PSU's. The documentation I've found says it is supported but not recommended.
View 1 Replies
View Related
Jul 29, 2012
in LMS (4.1) installing guide, table 'Software and Hardware Requirements for Soft Appliance', it is stated Memory and CPURequirement:
• 4 GB, 2 virtual CPU (< = 500 devices)Host CPU Core clock speed:
• Minimum 2.26 GHz Minimum Virtual CPU Reservations: Number of recommended virtual CPUs x 2.26 GHz:
• 4520 MHz (< = 500 devices)
I have HP server with 6 core CPU 2.0GHz - does it mean it does not meet the minimum system requirements (2.26Ghz)? Will I be able to go pass the installation?
View 3 Replies
View Related
Mar 28, 2012
I've just reset our WISM2 in the test lab back to factory default as I needed to reconfigure the 6500 and the WISM2 itself. Bearing in mind I had it working before.I've just renamed and re-addressed some of the vlans so things flow better and make it easier to add more WISM2s in the future.Now I've run through the initial configuration and it's rebooted ok and show WISM status is showing Oper-Up and there's a port channel 407 been created as I would expect. However, I am unable to get to the management interface via GUI or SSH. In fact from the 6500 I can't even ping the management interface (but I can the service port).The Vlans have been changed in the 6500 config so it knows the native-vlan and service vlan etc and all the vlans are up/up.
View 17 Replies
View Related
Feb 7, 2013
I've installed our previous WISMs and other WISM2s previously and never had a problem.
6500 running SXJ2. WISM2 running 7.3.101.0 (which is what the rest of our WISM2s are on)
Insert WISM and go through initial setup. Run a show wism status on the 6500, and show sysinfo on the WISM. All looks good. Service port and management vlans are up. From the 6500 I can ping the service port IP, but not the management IP. From the WISM I can't ping the managment default gw but I can the service port. Unable to get anything back from the GUI..not surprising as not even ping works.
Now, as I said I've done it this way many times before...in fact I'm following my documentation from the last successful implementation and even adding in Cisco docs.
View 7 Replies
View Related
Jul 21, 2012
how to safely remove the WiSM2 from the Catalyst 6500 series switch? According to the documentation "Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note":
To remove the WiSM2, perform these steps:
Step1 Shut down the module by one of these methods: In privileged mode from the router prompt, enter the hw-mod module mod shutdown command. NoteIf you enter this command to shut down the module, you must enter the following commands in global configuration mode to restart (power down, and then power up) the module: Router# no power enable module modRouter# power enable module mod If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.
Step2 Verify that the WiSM2 shuts down. Do not remove the module from the switch until the POWER LEDis off.
But, in the case of Step1 (1st methods) I do not see a option "shutdown" in the command "hw-mod module 3"...
All I prompted to enter is: c6500#hw-module module 3 ?
boot Specify boot options for the module through Power Management Bus control register
reset Reset specified component
simulate Simulate options for the module Is it hidden options?
IOS version of c6500 is 12.2(33)SXJ1
In the case of Step2 (2nd methods) there is not any button on the front panel of the module?
And yet, it is better to remove the module configuration manually or use the command module clear-config prior to removing the module?
View 14 Replies
View Related
Dec 16, 2012
it is normal for the WISM2 time to be resetted to default of 1 Jan 2000 after rebooting the 6506E if no NTP is configured?I had to configure it back to the correct time. If not, the APs will not come up.Also, does the ap or wlc keep track of the ap group the ap is provisioned to?
View 3 Replies
View Related
Jul 5, 2011
Got a question regarding 2921 modules. Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?
As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 4 Replies
View Related
Oct 16, 2011
I configure two WIC-1DSU-T1-v2 interfaces with a T1 crossover cable. What are the mimimum configurations to do to communicate from LAN1 (int fa0/0 of one 1841 router) to LAN2 (int fa0/0 of the second 1841 router) ?
Do I need a routage protocole ? And if yes wich one ? Interne or externe (RIP or BGP) Or static route is enough ? Also, is that I should put a encapsulation, like ppp ? Is it neccessary on a point to point line ?
Finally what about the following commands, do I need it ?
service-module t1 clock source internal
service-module t1 timeslots 1-24 speed 64
service-module t1 framing esf
service-module t1 linecode b8zs
View 4 Replies
View Related
Jun 10, 2011
belkin n wireless router minimum coverage ?
View 1 Replies
View Related
Nov 28, 2011
what are the things needed in setting a cyber cafe with minimum of 5pcs eg the most most profitable model, fast.
View 10 Replies
View Related
Oct 2, 2012
We have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport I would think I should have more, but have not had any issues with a few power outages
View 1 Replies
View Related
Aug 15, 2011
What is the minimum platform that supports GETVPN over DMVPN?
I have been looking around cisco website but couldn't find a document with the supported platforms.
We have branch offices with Cisco 861 routers and i would like to know if we could use GETVPN with these routers.
View 1 Replies
View Related
Sep 26, 2012
what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
View 2 Replies
View Related
Mar 13, 2012
need an access point configured in the user minimum because I was looking and some had up to 49 LAP connections at the same time. I have a WLC 4402 VERSION 7.0.98
View 1 Replies
View Related
Apr 5, 2011
I'm running WCS 7.0 on a WLSE appliance. Lately WCS has produced the following alarm:WCS 150.3.101.7 does not meet the minimum hardware requirements for disk space. Available: '29'GB. Minimum requirement: '30'GB. I have old WCS versions (3, 4, 5 and 6) so could delete those but I'm wary in case I take out the data too.
View 2 Replies
View Related
Apr 28, 2013
give me a link to where I can find the minimum code version for N55-M16UP expansion card for a Nexus 5k?
View 1 Replies
View Related
Oct 17, 2012
what is the minimun privilege level to assign at username account on ASA 5505 to grant the access with AnyConnect?
username ... privilege ?
View 4 Replies
View Related
