I'm running WCS 7.0 on a WLSE appliance. Lately WCS has produced the following alarm:WCS 150.3.101.7 does not meet the minimum hardware requirements for disk space. Available: '29'GB. Minimum requirement: '30'GB. I have old WCS versions (3, 4, 5 and 6) so could delete those but I'm wary in case I take out the data too.
View 2 RepliesI have this that comes up when i go on the networking
View 2 Replies View Relatedin LMS (4.1) installing guide, table 'Software and Hardware Requirements for Soft Appliance', it is stated Memory and CPURequirement:
• 4 GB, 2 virtual CPU (< = 500 devices)Host CPU Core clock speed:
• Minimum 2.26 GHz Minimum Virtual CPU Reservations: Number of recommended virtual CPUs x 2.26 GHz:
• 4520 MHz (< = 500 devices)
I have HP server with 6 core CPU 2.0GHz - does it mean it does not meet the minimum system requirements (2.26Ghz)? Will I be able to go pass the installation?
Got a question regarding 2921 modules. Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?
As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
My SCE1010 show the alert "Not enough disk space" in log.I find old discuss , someone say can delete the file: /tffs0/SYSTEM/PREVDBG.TXT , because the file is too big.But I don't confirm delete the file will not effect system work fine. [code]
View 8 Replies View RelatedWe are getting ready to bring up 2 new 5.1 ACS servers to replace our ACS 4.2 configuration.The documentation says that 512GB of disk space is required for each server. This means we will need to request1 TB of disk space. The VMware folks in our group are asking why we need so much space when the 4.2 servers are only using 20 gigs including the OS.
View 3 Replies View Relatedi'm about to configure a syslog server to receive syslog messages from a Cisco ASA5510 and being it a one week test I was wondering how much space should I allocate on the machine hosting the tool (kiwi syslog). I see that the ASA fills the internal syslog buffer to 4MB and then it overrides it. How many messages would those 4MB be?
View 2 Replies View RelatedOne of the file servers in your office is running out of space on the D: volume. There is unallocated space available on the same disk as the D: volume, as well as on other disks.What option should you choose to reduce administrative effort and minimize the chance of volume failure?
View 3 Replies View RelatedIn Soft Apliance 4.2.2 I keep up getting diskWatcher Available space message:
It is fresh installation:
[LMS-500/root-ade ~]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/smosvg-usrvol
[Code].....
I am confused about the cisco docs:What is the minimum WLC/WCS version to support WISM2 controllers ?
The datasheet of WISM2 says "minimum 7.0.116.0"
URL
However the release notes of 7.0.116.0 do not mention the WISM2 module ?
URL
The release notes of 7.0.220.0 do mention the WISM2:
URL
I need to be absolutely sure as there are other software dependencies between 7.0.116.0 and 7.0.220 (regarding required MSE and Aeroscout versions).
With WCS 7.0.172.0 and WLC 7.0.116.0, will we have WISM2 support ?
I configure two WIC-1DSU-T1-v2 interfaces with a T1 crossover cable. What are the mimimum configurations to do to communicate from LAN1 (int fa0/0 of one 1841 router) to LAN2 (int fa0/0 of the second 1841 router) ?
Do I need a routage protocole ? And if yes wich one ? Interne or externe (RIP or BGP) Or static route is enough ? Also, is that I should put a encapsulation, like ppp ? Is it neccessary on a point to point line ?
Finally what about the following commands, do I need it ?
service-module t1 clock source internal
service-module t1 timeslots 1-24 speed 64
service-module t1 framing esf
service-module t1 linecode b8zs
how to ftp a file with date in it's name. for ex.reportname filename yyyymmdd.cvname with space
View 3 Replies View Relatedi am using 1 gb net for 1 mnth.hw to save my netspace
View 1 Replies View RelatedWhy do i have 0 bytes of free space on my cd rom??
View 1 Replies View Relatedbelkin n wireless router minimum coverage ?
View 1 Replies View Relatedwhat are the things needed in setting a cyber cafe with minimum of 5pcs eg the most most profitable model, fast.
View 10 Replies View RelatedI have two phones Cisco 7940 with firmware 8.12. Configuration:
line1_shortname "George Steel"
line1_displayname "George Steel"
line1_name: 1
line1_authname: 1
line1_password: 123
When I call to another phone as the caller's name appears GeorgeSteel (no space). With firmware 8.8 it does not do ..
I am trying to upgrade a router 2811, the flash has 64 mb and currently has a IOS 32 mb, but require update it with a IOS 37 mb.
What should I do?, I cannot have the two ios in the flash.
LMS 4.2 Soft Apliance has default:
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/smosvg-optvol
105G 4.8G 95G 5% /opt
/dev/mapper/smosvg-varvol
53G 268M 50G 1% /var
Where to create Backup folder? Under /opt or /var ?
We have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport I would think I should have more, but have not had any issues with a few power outages
View 1 Replies View RelatedWhat is the minimum platform that supports GETVPN over DMVPN?
I have been looking around cisco website but couldn't find a document with the supported platforms.
We have branch offices with Cisco 861 routers and i would like to know if we could use GETVPN with these routers.
what should it be the minimum IOS version that I require on my WS-C6509-E equipments to support "logging origin-id" command?
Cisco documentation says that this command was introduced in 12.2(15)T, and integrated into 12.2(33)SXH.
BUT my Cisco switches have 12.2(33)SXH5 IOS version......and they do not support "logging origin-id".
(config)#logging ? Hostname or A.B.C.D IP address of the logging host buffered Set buffered logging parameters buginf Enable buginf logging for debugging cns-events Set CNS Event logging level console Set console logging parameters count Count every log message and timestamp last occurance esm Set ESM filter restrictions event Global interface events exception Limit(code)
I am trying to upgrade my IOS on a 3550 switch.The switch has 15MB of space total.When I delete the current IOS it leaves only 8MB of space.I need 10MB of space for the new image.Where is this other space being taken up? [code]
View 3 Replies View Relatedwe need to interconnect multiple branch office (CISCO 1841 with VWIC-1MFT-E1 ) via E1 links to the main site (CISCO 3745 with NM-8E1 IMA ). We succeeded to connect them using the same VWIC-1MFT-E1 at both sides (Branch / HQ), but I need to connect up to 10 sites in the future, so we thought that may be we can use ( NM-8E1 IMA) to make it possible and to save some space for any future upgrades. Honestly, we couldn't find any E1 related commands to configur this card (NM-8E1 IMA). Did we choosed the wrong card (NM-8E1 IMA).?
View 5 Replies View RelatedI am trying to upgrade my IOS on a 3550 switch.The switch has 15MB of space total.When I delete the current IOS it leaves only 8MB of space.I need 10MB of space for the new image.Where is this other space being taken up?
View 2 Replies View RelatedI want to upgrade IOS on 1811 from 12.4(11)T3 to 12.4(15)T16.
As a standard CF size in the 1811 is 32 M, so I have to free some space.
Here the strange things starts.
dir issued on the router shows thet ther is no image on the flash!
dir
Directory of flash:/
No files in directory
31940608 bytes total (12771328 bytes free)
sh ver shows that
uptime is 19 weeks, 2 days, 9 hours, 22 minutes
System returned to ROM by power-on
System restarted at 15:21:30 EEST Tue Jul 26 2011
System image file is "flash:c181x-advipservicesk9-mz.124-11.T3.bin"
The other strange thing is that some space is allocated for something!
(flash size) 3194060 - 12771328 (free) = 19169280 (space allocated to ???)
Just now router is running IOS c181x-advipservicesk9-mz.124-11.T3.bin The size of this IOS is 19 155 816, that is approximately equal to the size that allocated to something invisible.
fsck flash and format flash doesn't work. Bug Toolkit doesn't show any bugs similar to my issue.
need an access point configured in the user minimum because I was looking and some had up to 49 LAP connections at the same time. I have a WLC 4402 VERSION 7.0.98
View 1 Replies View Relatedgive me a link to where I can find the minimum code version for N55-M16UP expansion card for a Nexus 5k?
View 1 Replies View Related what is the minimun privilege level to assign at username account on ASA 5505 to grant the access with AnyConnect?
username ... privilege ?
I am looking to install 2 1552I outdoor AP's. I can't find what the minimum code version is on the WISM controller that supports this AP.I am running 7.0.98.0 on the WISM. Where can I find this information?
View 4 Replies View Relatedjust happened recently when im typing in threads or for websites, the second i hit the space bar two pop up ads appear making me have to close them to get back to what i was typing. These sites are annoying as you have to press leave page as well to close it. as you carry on typing the second you hit the space bar again it does another two pop-ups, which you can imaging gets annoying lol. I'm running Webroot full edition from a shop legit and would have thought it would prevent this happening? Is their anything i can do to stop this and would you like me to run a virus scan and post results?
View 3 Replies View RelatedI want to know that what is the minimum acceptable size of preamble in ethernet frame. if it is less than 7 bytes before sfd begins , will the packet drop?
View 1 Replies View RelatedWhat is the equivalent of the command "show flash" in IOS for the CSS11503 as I would like to view available flash space on the CSS11500 series load balancers?
View 3 Replies View Related