LMS 4.2 Soft Apliance has default:
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/smosvg-optvol
105G 4.8G 95G 5% /opt
/dev/mapper/smosvg-varvol
53G 268M 50G 1% /var
Where to create Backup folder? Under /opt or /var ?
We have an installation of Cisco Prime LMS 4.1 soft appliance on VMware and i would like to ask if it is possible to backup the database on an external drive other than the 'local' LMS hard disk.
View 3 Replies View RelatedI have to install Prime LMS 4.2 on ESX customer infrastructure (ova image as soft appliance). The customer would like to know if LMS 4.2 is compatible with his backup agents :
* Symantec Veritas Netbackup (v7.1.0.2)
* Control-m (v6.4.01.300)
If not, what would be the best solution to backup the server ? Are the VMware tools supported now ?
I try to upgrade LMS 4.2 to LMS 4.2.1 on a soft appliance and i got this error. To upgrade from LMS 4.2 to LMS 4.2.1:
lms/admin# conf t
lms/admin(config)# repository myrepo
lms/admin(config-Repository)# url disk://opt
lms/admin(config-Repository)# end
lms/admin# application upgrade Cisco_Prime_LAN_Management_Solution_4_2_1upgrade.tar.gz myrepo
Save the ADE-OS running configuration?(yes/no) [yes]? yes
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
% Local file not found
lms/admin#
While running the install wizard of soft appliance LMS 4.1 it asks for hostname and also the domain during the install. Is the hostname suppose to be fully qualified domain name exp: foo.blah.com or just hostname without fqdn exp: foo? Reason why I ask is when I ran the following command below in the shell it doesn't look like it is setup correctly. Also if I did the install without my hostname in dns first will this mess up my install?
View 3 Replies View RelatedI have a new installation of LMS 4.2 on the Soft Appliance and seem ot be only able to configure backups to the local disk? There is no option to select any of the configured repositories like there is in ACS. I can backup to /local disk, after change to filesystem as below:
chgrp casusers -R /local disk chmod 0775 /local disk
But the issue is, how to I get this off the box in an automated fashion so it can be part of our corporate backup schedule?
I am trying to setup prime LMS 4.2 with a pair of soft appliance. As I understand that HA is possible with the use of veritas/vmware for windows/solaris; I was wondering what are the possible high availability options available with a pair of prime LMS appliances? Can it form active/secondary with data synchronization/data redundancy of the LMS on top of the traditional backup/restore of the lms?
View 1 Replies View RelatedI am trying to create a VBR soft pvc across a T3 and T1 backup link, but I am confused about what values to use for PCR, SCR and MCR. If I use high values for the T3, what will happen when this link is down and the soft PVC reroutes across the T1? I would like to use percents (%) for the values, i.e. voice can use 25% of the link, then it would make more sense when using the backup T1 link.
View 2 Replies View RelatedI upgraded wcs to version 7.0.172 and migrated it to new server and ip address. The upgrade was done by install wcs 7.0.172 on new server and restoring a backup. I also upgraded the location appliance from 6.0.101.0 to 6.0.202.0. The wcs can see the location appliance without a problem. The problem occurs when i try to backup the location appliance. The wcs appears to run the backup and completes with a success but i cannot find the backup file in the ftp directory. wcs backup to ftp folder is fine.is a there a way of doing a manual backup the location appliance what logs can i check to see whether the backup is taking place or not?
View 2 Replies View RelatedI am running windows based acs 3.3 in my lan environment going to be replaced with acs 1120 appliance running acs 4.2.1.15 , ACS 3.3 database has been built upto 4.2.0.124 ,step by step by upgrade process
1) acs 3.3.3.14---> 4.1.1.24
2) acs 4.1.1.24 ----> 4.2.0.124 .
now my database is with 4.2.0.124 dmp file , I cannot upgrade my database to 4.2.1.15 because 4.2.1.15 patch is not applicable & executable on 90 days evalution package of 4.2.0.124 of windows platform .
can i import my windows based 4.2.0.124 datbase directly to my acs appliance running 4.2.1.15.3 ??? , else its requires any step to be done to modify the windows based databse matching to appliance windows verison once .
I could see on appliance under restore settings the following options (restore from 4.2.0 backup file to acs 4.2.1)
We have an ACE Appliance in a DMZ and the ACE Appliance's Admin Context IP is translated between ACE and ANM. The ANM Server does not get translated. It is just the opposite then in another Community discussion.
Our Problem: When adding the ACE4710 Appliance to the ANM imported Device List, we use the ACE's NATed Admin Context IP. Import works well, but ANM reflects the Admin Context IP with it's real configured IP. Polling the ACE Appliance does not work therefore.
Is there a possibility of telling the ANM, that the ACE has to be polled through a NATed IP? I could not find a field to set a NATed Mgmt IP.
Configured IP on ACE Admin Context: 192.168.0.10
NATed ACE Admin Context IP: 172.16.0.10
Imported ACE with IP 172.16.0.10 into ANM, but ANM polls for Rserver, Vserver, Probes, etc. via 192.168.0.10 - which is not reachable from the ANM.
Before nearly four years we have purchased 4 Cisco ASA 5500 Device for our organization.Out of these four device currently two are active in field and other two we kept as a spare.Now, in one active device we are facing very rare and strange issue.
The device automatically soft reboot once in nearly 60 days and we do not have any pre or post symptoms of this incident only server logs providing us this information.The device itself located in very controlled environment in a data center where physical tampering or temperature waviness is not possible.
We also asked one Cisco Expert from data center but still issue is not solved.Before two month, using remote syslog service we also started log redirection to a server so that when such incident occurs we have something to analyze but it is worthless log has nothing to tell us.
My questions are
1. "It is a hardware fault or software issue?"
2. "Is it possible with Cisco 5500 that automatically it reboots due to some internal hardware/software issue, if yes how we can trap or monitor it?
[code]...
We recently upgraded to higher speed internet and were to "reset" our modem, which is PCI Soft Data Fax Modem With SmartCP.How does one "reset" their modem?
View 1 Replies View RelatedI have a rather complex issue that involves a Cisco softswitch, a Cisco router configured for BGP routing, a L2 Cisco switch, and two RAD IPMUXs.I am including a flat diagram that illustrates the layer 2 connections. On the diagram, the number adjacent to the vertical connection bar is the vlans allowed on that connection, either switchport access or trunk.
I use BGP routing on the router to advertise various routes. The issue is that the routes for the RAD IPMUX216 and RAD24 are both being advertised correctly and can be seen from remote sites. For example, from any remote site, I can ping any address on vlan 60 such as the switch, router, and IMMUX216 IPs. However, I can only ping the vlan 61 IPs for the router and switch, but not the RAD24. Even from the Softswitch and Router, I cannot ping the vlan 61 ip of the RAD24, 172.22.248.6. I can ping the softswitch from the router and vice-versa.
Here is a flat diagram for the network with some snippets of code. I can provide more info if needed. I changed the routable IPs just to hide some of our actual info. If I ping 172.22.248.6 from the softswitch and then issue the "sh arp" command, I get:
Victoria-SW#sh arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.22.248.1 0 0016.4650.c411 ARPA Vlan61
Internet 172.22.255.6 - 0019.5678.7d43 ARPA Vlan80
Internet 172.22.248.6 0 Incomplete ARPA
Internet 172.22.240.14 - 0019.5678.7d42 ARPA Vlan60
Internet 172.22.240.13 0 0020.d239.01a0 ARPA Vlan60
Internet 172.22.248.5 - 0019.5678.7d44 ARPA Vlan61
Internet 172.22.240.1 69 0016.4650.c411 ARPA Vlan60
Ok I have a toshiba satellite with the above stated modem in place, however I am not sure if the modem is wireless capable. I have been trying to figure out how to connect it to my network.
View 2 Replies View RelatedOne of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies View RelatedIn Soft Apliance 4.2.2 I keep up getting diskWatcher Available space message:
It is fresh installation:
[LMS-500/root-ade ~]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/smosvg-usrvol
[Code].....
how to ftp a file with date in it's name. for ex.reportname filename yyyymmdd.cvname with space
View 3 Replies View Relatedi am using 1 gb net for 1 mnth.hw to save my netspace
View 1 Replies View RelatedWhy do i have 0 bytes of free space on my cd rom??
View 1 Replies View RelatedI have two phones Cisco 7940 with firmware 8.12. Configuration:
line1_shortname "George Steel"
line1_displayname "George Steel"
line1_name: 1
line1_authname: 1
line1_password: 123
When I call to another phone as the caller's name appears GeorgeSteel (no space). With firmware 8.8 it does not do ..
My SCE1010 show the alert "Not enough disk space" in log.I find old discuss , someone say can delete the file: /tffs0/SYSTEM/PREVDBG.TXT , because the file is too big.But I don't confirm delete the file will not effect system work fine. [code]
View 8 Replies View RelatedI am trying to upgrade a router 2811, the flash has 64 mb and currently has a IOS 32 mb, but require update it with a IOS 37 mb.
What should I do?, I cannot have the two ios in the flash.
We are getting ready to bring up 2 new 5.1 ACS servers to replace our ACS 4.2 configuration.The documentation says that 512GB of disk space is required for each server. This means we will need to request1 TB of disk space. The VMware folks in our group are asking why we need so much space when the 4.2 servers are only using 20 gigs including the OS.
View 3 Replies View RelatedI am trying to upgrade my IOS on a 3550 switch.The switch has 15MB of space total.When I delete the current IOS it leaves only 8MB of space.I need 10MB of space for the new image.Where is this other space being taken up? [code]
View 3 Replies View Relatedwe need to interconnect multiple branch office (CISCO 1841 with VWIC-1MFT-E1 ) via E1 links to the main site (CISCO 3745 with NM-8E1 IMA ). We succeeded to connect them using the same VWIC-1MFT-E1 at both sides (Branch / HQ), but I need to connect up to 10 sites in the future, so we thought that may be we can use ( NM-8E1 IMA) to make it possible and to save some space for any future upgrades. Honestly, we couldn't find any E1 related commands to configur this card (NM-8E1 IMA). Did we choosed the wrong card (NM-8E1 IMA).?
View 5 Replies View RelatedI am trying to upgrade my IOS on a 3550 switch.The switch has 15MB of space total.When I delete the current IOS it leaves only 8MB of space.I need 10MB of space for the new image.Where is this other space being taken up?
View 2 Replies View RelatedI want to upgrade IOS on 1811 from 12.4(11)T3 to 12.4(15)T16.
As a standard CF size in the 1811 is 32 M, so I have to free some space.
Here the strange things starts.
dir issued on the router shows thet ther is no image on the flash!
dir
Directory of flash:/
No files in directory
31940608 bytes total (12771328 bytes free)
sh ver shows that
uptime is 19 weeks, 2 days, 9 hours, 22 minutes
System returned to ROM by power-on
System restarted at 15:21:30 EEST Tue Jul 26 2011
System image file is "flash:c181x-advipservicesk9-mz.124-11.T3.bin"
The other strange thing is that some space is allocated for something!
(flash size) 3194060 - 12771328 (free) = 19169280 (space allocated to ???)
Just now router is running IOS c181x-advipservicesk9-mz.124-11.T3.bin The size of this IOS is 19 155 816, that is approximately equal to the size that allocated to something invisible.
fsck flash and format flash doesn't work. Bug Toolkit doesn't show any bugs similar to my issue.
just happened recently when im typing in threads or for websites, the second i hit the space bar two pop up ads appear making me have to close them to get back to what i was typing. These sites are annoying as you have to press leave page as well to close it. as you carry on typing the second you hit the space bar again it does another two pop-ups, which you can imaging gets annoying lol. I'm running Webroot full edition from a shop legit and would have thought it would prevent this happening? Is their anything i can do to stop this and would you like me to run a virus scan and post results?
View 3 Replies View RelatedWhat is the equivalent of the command "show flash" in IOS for the CSS11503 as I would like to view available flash space on the CSS11500 series load balancers?
View 3 Replies View Relatedwe have an ASA5520 need upgrade new anyconnect client, but the new version is too big, so it's no enough space. I want to delete the ASDM image to free the more space. My question is when I delete the ASDM image,if I could manage the ASA from web browser?
View 5 Replies View Relatedi'm about to configure a syslog server to receive syslog messages from a Cisco ASA5510 and being it a one week test I was wondering how much space should I allocate on the machine hosting the tool (kiwi syslog). I see that the ASA fills the internal syslog buffer to 4MB and then it overrides it. How many messages would those 4MB be?
View 2 Replies View RelatedI have a 5915 mobile router with software version 15.2(1r)GC1. Ports FE0/0 and FE0/1 are routed ports. Ports FE0/2 through FE0/4 are layer 2 switched ports. I'd like to put FE0/1 and FE0/2-4 in the same address space so that all four ports can be used as a single LAN and FE0/0 would be used as a WAN port. How do I configure the router to place FE0/1 and FE0/2-4 in the same LAN.
View 1 Replies View Related