We have an installation of Cisco Prime LMS 4.1 soft appliance on VMware and i would like to ask if it is possible to backup the database on an external drive other than the 'local' LMS hard disk.
View 3 Replies
I have to install Prime LMS 4.2 on ESX customer infrastructure (ova image as soft appliance). The customer would like to know if LMS 4.2 is compatible with his backup agents :
* Symantec Veritas Netbackup (v7.1.0.2)
* Control-m (v6.4.01.300)
If not, what would be the best solution to backup the server ? Are the VMware tools supported now ?
I am trying to setup prime LMS 4.2 with a pair of soft appliance. As I understand that HA is possible with the use of veritas/vmware for windows/solaris; I was wondering what are the possible high availability options available with a pair of prime LMS appliances? Can it form active/secondary with data synchronization/data redundancy of the LMS on top of the traditional backup/restore of the lms?
View 1 Replies View RelatedLMS 4.2 Soft Apliance has default:
Filesystem Size Used Avail Use% Mounted on
/dev/mapper/smosvg-optvol
105G 4.8G 95G 5% /opt
/dev/mapper/smosvg-varvol
53G 268M 50G 1% /var
Where to create Backup folder? Under /opt or /var ?
I try to upgrade LMS 4.2 to LMS 4.2.1 on a soft appliance and i got this error. To upgrade from LMS 4.2 to LMS 4.2.1:
lms/admin# conf t
lms/admin(config)# repository myrepo
lms/admin(config-Repository)# url disk://opt
lms/admin(config-Repository)# end
lms/admin# application upgrade Cisco_Prime_LAN_Management_Solution_4_2_1upgrade.tar.gz myrepo
Save the ADE-OS running configuration?(yes/no) [yes]? yes
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
% Local file not found
lms/admin#
While running the install wizard of soft appliance LMS 4.1 it asks for hostname and also the domain during the install. Is the hostname suppose to be fully qualified domain name exp: foo.blah.com or just hostname without fqdn exp: foo? Reason why I ask is when I ran the following command below in the shell it doesn't look like it is setup correctly. Also if I did the install without my hostname in dns first will this mess up my install?
View 3 Replies View RelatedI have a new installation of LMS 4.2 on the Soft Appliance and seem ot be only able to configure backups to the local disk? There is no option to select any of the configured repositories like there is in ACS. I can backup to /local disk, after change to filesystem as below:
chgrp casusers -R /local disk chmod 0775 /local disk
But the issue is, how to I get this off the box in an automated fashion so it can be part of our corporate backup schedule?
I am trying to create a VBR soft pvc across a T3 and T1 backup link, but I am confused about what values to use for PCR, SCR and MCR. If I use high values for the T3, what will happen when this link is down and the soft PVC reroutes across the T1? I would like to use percents (%) for the values, i.e. voice can use 25% of the link, then it would make more sense when using the backup T1 link.
View 2 Replies View RelatedI'm looking for getting a Cisco prime NCS appliance (PRIME-NCS-APL-K9). I'm a little bit confused regarding to the license scheme:
1. Does the appliance has any license coming with it or we need to order the license separately?
2. If I have an WLC 5508 (license support 12 APs) & 12 3500 APs, then number of devices counted will be 1 (WLC) or 12 (APs) or 13 (WLC + APs) ?
I upgraded wcs to version 7.0.172 and migrated it to new server and ip address. The upgrade was done by install wcs 7.0.172 on new server and restoring a backup. I also upgraded the location appliance from 6.0.101.0 to 6.0.202.0. The wcs can see the location appliance without a problem. The problem occurs when i try to backup the location appliance. The wcs appears to run the backup and completes with a success but i cannot find the backup file in the ftp directory. wcs backup to ftp folder is fine.is a there a way of doing a manual backup the location appliance what logs can i check to see whether the backup is taking place or not?
View 2 Replies View RelatedI am running windows based acs 3.3 in my lan environment going to be replaced with acs 1120 appliance running acs 4.2.1.15 , ACS 3.3 database has been built upto 4.2.0.124 ,step by step by upgrade process
1) acs 3.3.3.14---> 4.1.1.24
2) acs 4.1.1.24 ----> 4.2.0.124 .
now my database is with 4.2.0.124 dmp file , I cannot upgrade my database to 4.2.1.15 because 4.2.1.15 patch is not applicable & executable on 90 days evalution package of 4.2.0.124 of windows platform .
can i import my windows based 4.2.0.124 datbase directly to my acs appliance running 4.2.1.15.3 ??? , else its requires any step to be done to modify the windows based databse matching to appliance windows verison once .
I could see on appliance under restore settings the following options (restore from 4.2.0 backup file to acs 4.2.1)
I try to create a reposiroty for FTP Backup but it is not working with directories. Isn't it possible to create FTP repositories with directories?
I need to ad this URL e.g.: ftp://server/IT/Wi-Fi/Backup
This is not working. % Error reading directory on remote server
It works only when I add only the server. ftp://server/
Is there any way to add directories to the URL? Or what is wrong in my thought?
I think to use NFS but I'm not sure if that way is better as FTP, because FTP is default
I'm trying to restore backup after upgrading Cisco Prime v4.1 to v4.2. However, getting the following error in the log. [code] The log shows the error is a continuous one and affraid it may be a loop. Currently my restore progress is stuck at 70%RME restoration.[code]
View 2 Replies View RelatedWe are currently running Cisco prime 4.1 and want to make sure there is a backup of the configurations from our switches and routers. The VLANconfig is not collected according to the devicestatus dashboard. i am aware there were a known issue with LMS running on a virtual server and vlan not being able to be collected, is this issue resolved? i have tried the various workarounds with TAC support and it hasnt worked. We have the running and startup config collected for our devices when looking at the device status dashboard. does this mean if a switch crashes we can restore the config to a new switch immediately?
i saw there is a version 4.2. maybe this version resolves the issue with LMS on a virutal server? i cannot find the download to upgrade to 4.2 in the support section though.
We have an ACE Appliance in a DMZ and the ACE Appliance's Admin Context IP is translated between ACE and ANM. The ANM Server does not get translated. It is just the opposite then in another Community discussion.
Our Problem: When adding the ACE4710 Appliance to the ANM imported Device List, we use the ACE's NATed Admin Context IP. Import works well, but ANM reflects the Admin Context IP with it's real configured IP. Polling the ACE Appliance does not work therefore.
Is there a possibility of telling the ANM, that the ACE has to be polled through a NATed IP? I could not find a field to set a NATed Mgmt IP.
Configured IP on ACE Admin Context: 192.168.0.10
NATed ACE Admin Context IP: 172.16.0.10
Imported ACE with IP 172.16.0.10 into ANM, but ANM polls for Rserver, Vserver, Probes, etc. via 192.168.0.10 - which is not reachable from the ANM.
I'm currently running CiscoWorks LMS 4.0.1 on Windows 2003 under VMware and just got upgrade licensing for Prime Infrastructure 1.2. I am assuming that I will need to upgrade the current server to Prime LMS 4.2 in order to ensure that data migration to Prime Infrastructure goes well. I am planning to follow Cisco's recommendation to run Prime LMS and Prime Infrastructure in parallel for a time and migrate individual functions.
My real question is about Syslog handling. All of the managed devices are currently sending Syslog data to LMS. As a last step in the migration, is it possible to change the IP address of the Prime Infrastructure server to replace the Prime LMS server so that the Prime Infrastructure server will just start getting all the Syslog data, or do I need to go change hundreds of managed devices to point to a new address?
What is the relation between: cisco NCScisco Prime LMSCisco Prime infrastructure.As i orderd a Cisco Prime infrastructure from a Cisco Partner and what i got is :
x2 cisco NCS appliances
x1 DVD cisco prime infrastructure
x1 DVD Cisco prime 4.2
Before nearly four years we have purchased 4 Cisco ASA 5500 Device for our organization.Out of these four device currently two are active in field and other two we kept as a spare.Now, in one active device we are facing very rare and strange issue.
The device automatically soft reboot once in nearly 60 days and we do not have any pre or post symptoms of this incident only server logs providing us this information.The device itself located in very controlled environment in a data center where physical tampering or temperature waviness is not possible.
We also asked one Cisco Expert from data center but still issue is not solved.Before two month, using remote syslog service we also started log redirection to a server so that when such incident occurs we have something to analyze but it is worthless log has nothing to tell us.
My questions are
1. "It is a hardware fault or software issue?"
2. "Is it possible with Cisco 5500 that automatically it reboots due to some internal hardware/software issue, if yes how we can trap or monitor it?
[code]...
We recently upgraded to higher speed internet and were to "reset" our modem, which is PCI Soft Data Fax Modem With SmartCP.How does one "reset" their modem?
View 1 Replies View RelatedI have a rather complex issue that involves a Cisco softswitch, a Cisco router configured for BGP routing, a L2 Cisco switch, and two RAD IPMUXs.I am including a flat diagram that illustrates the layer 2 connections. On the diagram, the number adjacent to the vertical connection bar is the vlans allowed on that connection, either switchport access or trunk.
I use BGP routing on the router to advertise various routes. The issue is that the routes for the RAD IPMUX216 and RAD24 are both being advertised correctly and can be seen from remote sites. For example, from any remote site, I can ping any address on vlan 60 such as the switch, router, and IMMUX216 IPs. However, I can only ping the vlan 61 IPs for the router and switch, but not the RAD24. Even from the Softswitch and Router, I cannot ping the vlan 61 ip of the RAD24, 172.22.248.6. I can ping the softswitch from the router and vice-versa.
Here is a flat diagram for the network with some snippets of code. I can provide more info if needed. I changed the routable IPs just to hide some of our actual info. If I ping 172.22.248.6 from the softswitch and then issue the "sh arp" command, I get:
Victoria-SW#sh arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.22.248.1 0 0016.4650.c411 ARPA Vlan61
Internet 172.22.255.6 - 0019.5678.7d43 ARPA Vlan80
Internet 172.22.248.6 0 Incomplete ARPA
Internet 172.22.240.14 - 0019.5678.7d42 ARPA Vlan60
Internet 172.22.240.13 0 0020.d239.01a0 ARPA Vlan60
Internet 172.22.248.5 - 0019.5678.7d44 ARPA Vlan61
Internet 172.22.240.1 69 0016.4650.c411 ARPA Vlan60
Ok I have a toshiba satellite with the above stated modem in place, however I am not sure if the modem is wireless capable. I have been trying to figure out how to connect it to my network.
View 2 Replies View RelatedOne of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies View RelatedCan't see this in the documentation, as only Solaris to soft appliance is mentioned, so does anyone know if you can migrate data from LMS 4.0.1 on Windows 2008 to the soft appliance on LMS 4.1?
View 1 Replies View RelatedAfter upgrading our Cisco MSE to 7.4, the appliance does not stay connected to the network. Once the appliance is restarted, layer 3 echoes occur for about 2 minutes and then stop. The only way to get it to respond again, is to restart the appliance. Again, after a few minutes, it stops responding. I've checked the switch, and there is no port security set up on it. I've checked ACL's, and other potential culprits to no avail. The MSE interface is set up, and the device is configured.
View 12 Replies View RelatedI'm currently trying to install the Cisco LMS 4.2 Appliance on a VMware vSphere 4.0 environment.I'm following the [URL]. I downloaded the Cisco_Prime_LAN_Management_Solution_4_2.iso and I started the server.I get this screen and I choose option 1:
View 3 Replies View RelatedI could not SSH to ACS SE appliance? Why I could not, however I can do on another ACS SE.
note that I can ping the ACS SE, after disabling the CSA, so netowrk connectivity is ok.
Cisco Secure ACS: 4.2.0.124.
All users are located in the local identity store.So - assume I do not implement ACS but I do turn on password expiration after 60 or 90 days. Will a user whose password is about to expire attempts to authenticate against ACS 5.2, will they be notified that their password is about to expire?Also, when a user attempts to authenticate but their password expired yesterday, will they be prompted to change it and if so, how will that prompt to change it be presented?
View 3 Replies View RelatedA while back we were looking into upgrading our SUN/Oracle server to better service our CiscoWorks. Our vendor (partnered Cisco Vendor) told us that Cisco was developing an appliance like WCS and CNR that runs Redhat for CiscoWorks.Does any one have any info on this or could this be a rumor?
We do not run Windows devices on any of our network enterprise and this would be so cool!
Oracle is getting to be a clone of Windows..in our opinion
If this is true, I will happy to sit and wait for it.
We now run LMS 4.0 on a SUN/Oracle T2000 and it seems to be bottlenecking.
PXE E61 same error are comming in rsa envision appliance
View 1 Replies View RelatedMy site got the NAC-3315 appliance and we would like to reimage this appliance to inline posture mode (for VPN purpose)What's the proper migration process should deal with this? Is the NAC-3315 hardware comply with the Inline posture mode requirement?
View 4 Replies View RelatedHow to upgrade from ACS Se 1113 (running 4.2.0.124) to a new 1121 appliance running version 5.2. We also run RA for AD integration ?
View 5 Replies View Related Newly shipped cisco ACS appliance 1121 has been shipped with ACS version 5.0 , I need to downgrade to ACS version 4.2,0 , I could not see recovery CD or DVD for acs 4.2 along with shipment , Is ACS 1121 appliance is comptaible to acs 4.2.0 version ? .
My ACS BOM details
CSACS-1121-K9
ACS 1121 Appliance With 5.1 SW And Base license
[code]....
This is a new installation.I did to configure the ACS to connect to the AD to authenticate users and retrieve the user information for group mapping as following step. Go to Users and Identity Stores > External Identity Stores > Active Directory, and enter the domain name and provide a username/password that will allow connect to the domain.Next, click on the Test Connection button to validate joining the domain.
I got success test connection. But when I click Save Changes. I got error .
