Cisco :: LMS 4.1 Soft Appliance Host-name Setup

Jan 24, 2012

While running the install wizard of soft appliance LMS 4.1 it asks for hostname and also the domain during the install. Is the hostname suppose to be fully qualified domain name exp: foo.blah.com or just hostname without fqdn exp: foo? Reason why I ask is when I ran the following command below in the shell it doesn't look like it is setup correctly. Also if I did the install without my hostname in dns first will this mess up my install?

View 3 Replies


ADVERTISEMENT

Cisco :: Setup Prime LMS 4.2 With Pair Of Soft Appliance?

Jun 10, 2013

I am trying to setup prime LMS 4.2 with a pair of soft appliance. As I understand that HA is possible with the use of veritas/vmware for windows/solaris; I was wondering what are the possible high availability options available with a pair of prime LMS appliances? Can it form active/secondary with data synchronization/data redundancy of the LMS on top of the traditional backup/restore of the lms?

View 1 Replies View Related

Cisco :: LMS 4.2 Upgrade To LMS 4.2.1 On Soft Appliance

Jul 10, 2012

I try to upgrade LMS 4.2 to LMS 4.2.1 on a soft appliance and i got this error. To upgrade from LMS 4.2 to LMS 4.2.1:
 
lms/admin# conf t
lms/admin(config)# repository myrepo
lms/admin(config-Repository)# url disk://opt
lms/admin(config-Repository)# end
lms/admin# application upgrade Cisco_Prime_LAN_Management_Solution_4_2_1upgrade.tar.gz myrepo
Save the ADE-OS running configuration?(yes/no) [yes]? yes
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
% Local file not found
lms/admin#

View 3 Replies View Related

Cisco :: LMS Prime 4.1 Soft Appliance Backup

Jan 17, 2012

We have an installation of Cisco Prime LMS 4.1 soft appliance on VMware and i would like to ask if it is possible to backup the database on an external drive other than the 'local' LMS hard disk.

View 3 Replies View Related

Cisco :: Backup Space In LMS 4.2 Soft Appliance?

Oct 15, 2012

LMS 4.2 Soft Apliance has default:
 
Filesystem            Size  Used Avail Use% Mounted on
/dev/mapper/smosvg-optvol
105G  4.8G   95G   5% /opt
/dev/mapper/smosvg-varvol
53G  268M   50G   1% /var
 
Where to create Backup folder? Under /opt or /var ?

View 3 Replies View Related

Cisco :: LMS 4.2 Soft Appliance - Remote Backups

Nov 18, 2012

I have a new installation of LMS 4.2 on the Soft Appliance and seem ot be only able to configure backups to the local disk? There is no option to select any of the configured repositories like there is in ACS. I can backup to /local disk, after change to filesystem as below:

chgrp casusers -R /local disk chmod 0775 /local disk 

But the issue is, how to I get this off the box in an automated fashion so it can be part of our corporate backup schedule?

View 0 Replies View Related

Cisco :: Prime LMS 4.2 Soft Appliance Vmware Server Backup

Jun 13, 2012

I have to install Prime LMS 4.2 on ESX customer infrastructure (ova image as soft appliance). The customer  would like to know if LMS 4.2 is compatible with his backup agents  :

* Symantec Veritas Netbackup (v7.1.0.2)
* Control-m (v6.4.01.300)

If not, what would be the best solution to backup the server ? Are the VMware tools supported now ?

View 1 Replies View Related

Cisco Application :: ACE4710 Appliance To ANM Virtual Appliance NATed

Oct 12, 2011

We have an ACE Appliance in a DMZ and the ACE Appliance's Admin Context IP is translated between ACE and ANM. The ANM Server does not get translated. It is just the opposite then in another Community discussion.
 
Our Problem: When adding the ACE4710 Appliance to the ANM imported Device List, we use the ACE's NATed Admin Context IP. Import works well, but ANM reflects the Admin Context IP with it's real configured IP. Polling the ACE Appliance does not work therefore.
 
Is there a possibility of telling the ANM, that the ACE has to be polled through a NATed IP? I could not find a field to set a NATed Mgmt IP.
 
Configured IP on ACE Admin Context: 192.168.0.10
NATed ACE Admin  Context IP:           172.16.0.10
 
Imported ACE with IP 172.16.0.10 into ANM, but ANM polls for Rserver, Vserver, Probes, etc. via 192.168.0.10 - which is not reachable from the ANM.

View 2 Replies View Related

Cisco Switching/Routing :: 1941 - How To Setup PBR To Have Two Host

Feb 22, 2012

I have a 1941W that has a connection to my ISP (Gi0/1) and another connection to a remote lab (Gi0/0). Everything is working fine how it is setup. All my traffic from my internal networks can access the Internet and devices on the 192.168.201.0 /24 can access the Internet and the lab 10.89.0.0/16.
 
Now I want to have two devices (192.168.201.51 & .147) use Gi0/0 when accessing host 63.85.190.67. There is no route to this subnet since it reside in the remote lab. Here is what I have right now. How would I setup a PBR to have those two host use Gi0/0 when accessing 63.85.190.67
 
interface Vlan192
ip address 192.168.201.1 255.255.255.0
ip nat inside
ip virtual-reassembly (code)

View 12 Replies View Related

Cisco WAN :: ATM Soft Pvc Across T3 And T1 Backup?

May 3, 2006

I am trying to create a VBR soft pvc across a T3 and T1 backup link, but I am confused about what values to use for PCR, SCR and MCR.  If I use high values for the T3, what will happen when this link is down and the soft PVC reroutes across the T1?  I would like to use percents (%) for the values, i.e. voice can use 25% of the link, then it would make more sense when using the backup T1 link.

View 2 Replies View Related

Cisco VPN :: ASA 5500 - Way To Soft Reboot Automatically

Oct 31, 2011

Before nearly four years we have purchased 4 Cisco ASA 5500 Device for our organization.Out of these four device currently two are active in field and other two we kept as a spare.Now, in one active device we are facing very rare and strange issue.

The device automatically soft reboot once in nearly 60 days and we do not have any pre or post symptoms of this incident only server logs providing us this information.The device itself located in very controlled environment in a data center where physical tampering or temperature waviness is not possible.

We also asked one Cisco Expert from data center but still issue is not solved.Before two month, using remote syslog service we also started log redirection to a server so that when such incident occurs we have something to analyze but it is worthless log has nothing to tell us.

My questions are

1. "It is a hardware fault or software issue?"

2. "Is it possible with Cisco 5500 that automatically it reboots due to some internal hardware/software issue, if yes how we can trap or monitor it?

[code]...

View 3 Replies View Related

Cisco VPN :: Pix 515e - Remote Host Cannot Ping Any LAN Host

Jun 27, 2011

I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.

View 2 Replies View Related

Cisco VPN :: ASA 5510 Ping / Communication Host To Host

May 7, 2012

ASA 5510
Ver 8.2(5)
 
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.

View 4 Replies View Related

Broadband :: Reset PCI Soft Data Modem?

Feb 9, 2011

We recently upgraded to higher speed internet and were to "reset" our modem, which is PCI Soft Data Fax Modem With SmartCP.How does one "reset" their modem?

View 1 Replies View Related

Cisco WAN :: Complex Connectivity Involving Soft With IPMUX216 And RAD24

Aug 23, 2011

I have a rather complex issue that involves a Cisco softswitch, a Cisco router configured for BGP routing, a L2 Cisco switch, and two RAD IPMUXs.I am including a flat diagram that illustrates the layer 2 connections. On the diagram, the number adjacent to the vertical connection bar is the vlans allowed on that connection, either switchport access or trunk.
 
I use BGP routing on the router to advertise various routes. The issue is that the routes for the RAD IPMUX216 and RAD24 are both being advertised correctly and can be seen from remote sites. For example, from any remote site, I can ping any address on vlan 60 such as the switch, router, and IMMUX216 IPs. However, I can only ping the vlan 61 IPs for the router and switch, but not the RAD24. Even from the Softswitch and Router, I cannot ping the vlan 61 ip of the RAD24, 172.22.248.6. I can ping the softswitch from the router and vice-versa.
 
Here is a flat diagram for the network with some snippets of code. I can provide more info if needed. I changed the routable IPs just to hide some of our actual info. If I ping 172.22.248.6 from the softswitch and then issue the "sh arp" command, I get:
 
Victoria-SW#sh arp
Protocol  Address          Age (min)  Hardware Addr   Type   Interface
Internet  172.22.248.1            0   0016.4650.c411  ARPA   Vlan61
Internet  172.22.255.6            -   0019.5678.7d43  ARPA   Vlan80
Internet  172.22.248.6            0   Incomplete      ARPA
Internet  172.22.240.14           -   0019.5678.7d42  ARPA   Vlan60
Internet  172.22.240.13           0   0020.d239.01a0  ARPA   Vlan60
Internet  172.22.248.5            -   0019.5678.7d44  ARPA   Vlan61
Internet  172.22.240.1           69   0016.4650.c411  ARPA   Vlan60

View 2 Replies View Related

Can Pure IPv6 Host Ping A IPv4 Host?

Feb 10, 2011

I'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...

View 2 Replies View Related

Wireless :: Toshiba Soft Modem AMR Com3 Trying To Connect To Home Network

Dec 18, 2011

Ok I have a toshiba satellite with the above stated modem in place, however I am not sure if the modem is wireless capable. I have been trying to figure out how to connect it to my network.

View 2 Replies View Related

Linksys Wireless Router :: E4200 DCHP Client Table Doesn't Reset After Soft Reboot

Jul 15, 2011

One of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely.   However, I've recently had a few problems that only a full power down would fix.   In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot.   Is this intentional?   Is the soft reboot not really a full reboot? Can it be made a real reboot?

View 7 Replies View Related

Cisco :: Migration From Windows LMS 4.0.1 To Appliance 4.1?

Oct 4, 2011

Can't see this in the documentation, as only Solaris to soft appliance is mentioned, so does anyone know if you can migrate data from LMS 4.0.1 on Windows 2008 to the soft appliance on LMS 4.1?

View 1 Replies View Related

Cisco :: MSE 7.4 Appliance Stops Responding

Apr 2, 2013

After upgrading our Cisco MSE to 7.4, the appliance does not stay connected to the network.  Once the appliance is restarted, layer 3 echoes occur for about 2 minutes and then stop.  The only way to get it to respond again, is to restart the appliance.  Again, after a few minutes, it stops responding.  I've checked the switch, and there is no port security set up on it.  I've checked ACL's, and other potential culprits to no avail.  The MSE interface is set up, and the device is configured. 

View 12 Replies View Related

Cisco :: LMS 4.2 Appliance On VMware VSphere 4.0

Jul 31, 2012

I'm currently trying to install the Cisco LMS 4.2 Appliance on a VMware vSphere 4.0 environment.I'm following the [URL]. I downloaded the Cisco_Prime_LAN_Management_Solution_4_2.iso and I started the server.I get this screen and I choose option 1:

View 3 Replies View Related

Cisco AAA/Identity/Nac :: Unable To SSH To ACS 4.2.0.124 SE Appliance

Feb 20, 2010

I could not SSH to ACS SE appliance? Why I could not, however I can do on another ACS SE.
 
note that I can ping the ACS SE, after disabling the CSA, so netowrk connectivity is ok.
 
Cisco Secure ACS: 4.2.0.124.

View 5 Replies View Related

Cisco AAA/Identity/Nac :: Secure ACS 5.2 Appliance To Use Or Not To Use UCP

Nov 16, 2011

All users are located in the local identity store.So - assume I do not implement ACS but I do turn on password expiration after 60 or 90 days.  Will a user whose password is about to expire attempts to authenticate against ACS 5.2, will they be notified that their password is about to expire?Also, when a user attempts to authenticate but their password expired yesterday, will they be prompted to change it and if so, how will that prompt to change it be presented?

View 3 Replies View Related

Cisco :: CiscoWorks Appliance In T2000

Jul 25, 2011

A while back we were looking into upgrading our SUN/Oracle server to better service our CiscoWorks. Our vendor (partnered Cisco Vendor) told us that Cisco was developing an appliance like WCS and CNR that runs Redhat for CiscoWorks.Does any one have any info on this or could this be a rumor?

We do not run Windows devices on any of our network enterprise and this would be so cool!
 
Oracle is getting to be a clone of Windows..in our opinion
 
If this is true, I will happy to sit and wait for it.
 
We now run LMS 4.0 on a SUN/Oracle T2000 and it seems to be bottlenecking.

View 2 Replies View Related

Servers :: Error PXE E61 In RSA Appliance

Jul 11, 2012

PXE E61 same error are comming in rsa envision appliance

View 1 Replies View Related

Cisco :: 7.0.172 / Manual Backup The Location Appliance?

Jun 19, 2011

I upgraded wcs to version 7.0.172 and migrated it to new server and ip address. The upgrade was done by install wcs 7.0.172 on new server and restoring a backup. I also upgraded the location appliance from 6.0.101.0 to 6.0.202.0. The wcs can see the location appliance without a problem. The problem occurs when i try to backup the location appliance. The wcs appears to run the backup and completes with a success but i cannot find the backup file in the ftp directory. wcs backup to ftp folder is fine.is a there a way of doing a manual backup the location appliance what logs can i check to see whether the backup is taking place or not?

View 2 Replies View Related

Cisco AAA/Identity/Nac :: Re-image NAC-3315 Appliance To ISE

Mar 29, 2012

My site got the NAC-3315 appliance and we would like to reimage this appliance to inline posture mode (for VPN purpose)What's the proper migration process should deal with this? Is the NAC-3315 hardware comply with the Inline posture mode requirement?

View 4 Replies View Related

Cisco Security :: 1113 ACS Se Appliance Upgrade To 5.2

Mar 6, 2011

How to upgrade from ACS Se 1113 (running 4.2.0.124) to a new 1121 appliance running version 5.2. We also run RA for AD integration ?

View 5 Replies View Related

Cisco AAA/Identity/Nac :: ACS 1121 Appliance Downgrade To 4.2.0.124

May 2, 2011

Newly shipped cisco  ACS appliance 1121 has been shipped with ACS version 5.0 , I need to downgrade to ACS version 4.2,0 , I could not see recovery CD or DVD for acs 4.2 along with shipment , Is ACS 1121 appliance is comptaible to acs 4.2.0 version ? .
 
My ACS BOM details
CSACS-1121-K9
ACS 1121 Appliance With  5.1 SW And Base license

[code]....

View 2 Replies View Related

Cisco AAA/Identity/Nac :: Configure ACS 5.1 Appliance To Connect To AD

Jun 18, 2011

This is a new installation.I did to configure the ACS to connect to the AD to authenticate users and retrieve the user information for group mapping as following step. Go to Users and Identity Stores > External Identity Stores > Active Directory, and enter the domain name and provide a username/password that will allow connect to the domain.Next, click on the Test Connection button to validate joining the domain.
I got success test connection. But when I click Save Changes. I got error .

View 5 Replies View Related

Cisco AAA/Identity/Nac :: Licensing On C1121 ACS Appliance

Feb 13, 2012

01. I have one customer unit C1121 ACS system shipped with version 5.1. The customer buy the base license and large deployment license along with the purchase.
 
02. Fact is i have manually upgrade the system to version 5.3.0.40, and applying a trial license for it for administering the appliance.
 
a. If i now using the purchased base license and large deployment PAK to activate the system, would it still valid for me to continue using Version 5.3.0.40?

View 2 Replies View Related

Cisco AAA/Identity/Nac :: Expanding NIC On 3315 NAC / ISE Appliance

May 2, 2013

Is it possible to add another NIC to the Cisco 3315 NAC appliance. It ships with Four ethernet interfaces, but would like to add at least 1 extra interface i.e. PCI card if possible.

View 1 Replies View Related

Cisco AAA/Identity/Nac :: Up-gradation ACS 4.2.0.124.16 On Appliance 1113 To ACS 4.2.1.15

Jun 21, 2012

we have below softwares in the order to install one by one on the appliance 1113.

1)ACSse-Upgrade-Pkg-appl-mng-v4.2.1.15-K9.zip
(Appliance Management package)

2)ACSse-Upgrade-Pkg-acs-v4.2.1.15-K9.zip
(ACS Software package)

3)applAcs_4.2.1.15.8.zip
(ACS SE 4.2.1.15.8 cumulative patch)
 
take it forward to upgrade by step by step procedure. ( is that same like TFTP to transfer these packeges to appliance or different method? ) (we are using Windows XP system)

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved