Cisco Switching/Routing :: 1941 - NBAR Protocol Pack
Apr 4, 2013
I'm trying to upgrade NBAR protocol pack on my Cisco 1941 router, so i downloaded new NABR protocol pack (version 4.0.0) and transferred it into router flash via tftp. When i try to apply new protocol pack with command : ip nbar protocol-pack flash:[protocol-pack-name]
i got this error :
% NBAR Error : Advanced Protocol Pack can not be loaded on top of Standard Protocol Pack
The router is running IPBASE IOS with Security License, IOS image is c1900-universalk9-mz.SPA.153-1.T.bin. Does NBAR2 packages works on IO BASE images?
View 2 Replies
ADVERTISEMENT
Feb 15, 2011
How to hit the 32 interface nbar limit on an ASR? Our ASR1002 ESP5 is now grumbling: %NBAR-4-STILE_MAX_PD_INTF: NBAR protocol-discovery is enabled on maximum number of interfaces (32) supported by this platform..Is this expected to increase in future software revisions? (or is it a h/w limitation?)Is it the same limit regardless of ESP or will I get more (how many more?) if it is an e.g. ESP20?
View 1 Replies
View Related
Mar 19, 2012
i want to know, is c3650G or c3650X switches are already containing rack mounting pack or am i need to buy it seperatly?
View 3 Replies
View Related
Dec 28, 2011
My ISP is going to provide internet with dual path , for auto changover he (isp it admin) is planing for bgp implimentation.
is 1941 is supportable for bgp protocol ? Is it possible to create bandwitdh rate limit based on ip address on access list (be cause we are getting some 10 Ip address from isp , out of 10 ip address , 3 ip addres has to go 3 diffrent departments) , i want restrict theese 3 ip address with 1 mb traffic as 1:1.
View 1 Replies
View Related
Apr 18, 2012
I have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
On SW2:
*Mar 1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar 1 00:57:00.711: AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar 1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar 1 00:57:02.303: AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
[code].....
View 10 Replies
View Related
Mar 25, 2012
I have an environment where i have two nexus 7010 switches, along with 2 nexus 5510's. I need to run OSPF as a layer 3 routing protocol between the vpc peer links. I have 1 link being used as a keep alive link, and 3 other links being used as a VpC link.
1) Is it best to configure a separate Vpc VLAN i.e 1010
2) Is it best to configure a vrf context keep-alive
3) just have the management address as the peer ip's.
View 2 Replies
View Related
Jan 10, 2013
I have bought Cisco ISR 881 C880DATA-UNIVERSALK9-M with c880data-universalk9-mz.150-1.M7.bin ios.
command "show ver" tell me:
License Information for 'c880-data'
License Level: advsecurity Type: Permanent
Next reboot license Level: advsecurity
So I have advsecurity. On cisco site there was a thing URL
"Table 5. Cisco IOS Software Features on Cisco 880 Series: Advanced Security Feature Set (Default)"
that tell me I have RIP protocol to use. But when I type "router rip" command and sub router sommands like: network, passive-interface, redistribution. There are no in runnning-config such things after all I've done. It have not been saved.
then the command "show licence":
#show license
Index 1 Feature: advipservices
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
I need even RIPv2 to have simple routing information to exchange.
And I don't know. Cisco 880 series is G2 or G1. Cisco ISR beginning from 890 series is G2. About 880 I don't know. There no informanion about it or at least I have not found it yet. On one 891 is the same problem. When I type "router eigrp 1" everything is great. But when "router rip" - do no work.
View 9 Replies
View Related
Feb 24, 2013
I have encounterd a broplem on my Cisco 805 model.
When i use the command "show ip interface brief" the status shows "up" but the protocol is "down" on my serial interface.
The link between my to sites is down after this happend.
View 1 Replies
View Related
Apr 14, 2013
When I config BGP on my 3750X Switch, it show error as below:
protocol not in this image
should I need to upgrade the IOS or Where I can found a supported image (support BGP)
View 1 Replies
View Related
Jul 10, 2012
I am trying to enter this command in Cisco 2960 but the device is not accepting it. Is this because of IOS or this command is not available for 2960?
View 1 Replies
View Related
Jan 31, 2013
I am trying to review the port-channel configuration on a 6500 series. I am issuing the "show etherchannel summary" command and the out put shows the Group, Port-Channel, and Ports. It does not show me the protocol that is in use such as PAgP or LACP. Does this have to do with the Etherchannel in the "On" mode rather than "active", or "Auto"?
View 2 Replies
View Related
Jun 24, 2012
I have a 1941 router configured for Policy based routing with two ISPs.Two static default routes configured to point the gateways of respoective ISPs with same metric.But the problem is, packets are going throug the one ISP only while doing traceroute.
N/W connectivity:
ISP1-----> <----------------------> LAN1
| Router |
ISP-------> <----------------------> LAN 2
Below is my configuration :
Current configuration : 5958 bytes
!
! Last configuration change at 05:18:56 UTC Mon Jun 25 2012
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 26 Replies
View Related
Jun 18, 2012
I have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1
View 8 Replies
View Related
Dec 1, 2012
On our backbone (Cisco 6509) we have the following config.
spanning-tree mode rapid-pvst
spanning-tree extend system-id
spanning-tree vlan 1-200 priority 24576
1. is rapid-pvst the best spanning tree protocol to use? on some switches we have pvst (not rapid)
2. do all switches in the LAN need to use the same protocol?
3. does line 3 :priority 24576 mean that someone set tis switch as root manually? how can one further enforce the backbone as root (so noone adds a old switch with lower root id)
View 6 Replies
View Related
Oct 29, 2012
I'm trying to implement the UDLD protocol (Cisco-compatible), but face some problems. There is no enough information for implementing this protocol neither in RFC 5171 [URL] nor on [URL] How can I get a more detailed information regarding protocol state machines and timers?
View 2 Replies
View Related
Apr 10, 2013
We are using CISCO LMS 4.2.3 in our network in India, we are facing a issue regarding alarm generation for a protocol flap/down, especially when BGP / OSPF neighbourship got flapped.These flapping will result in the data service degradation , by which we came to know that some protocol flap may occurred at router end & then we go for the manual check by login into the router.after escalating the same to cisco we came to know that it is a bug of Cisco LMS. using any other method/technique to view the protocol down alarms automatically for cisco routers.
View 1 Replies
View Related
Dec 25, 2012
I want to configurate Vpdn protocol PPOE but i can not write protocol ppoe under vpdn group name on cisco 2811. cisco 2811 iso is 12.4 T adventurer and i upgrade it 15.1 advansecure but problem is still.
View 5 Replies
View Related
Jun 10, 2013
Will Resilient Ethernet Protocol (REP) run on all Cisco switches (2960S and 3010) or is it only available on Service Provider switches like the ME3400E?
View 2 Replies
View Related
Aug 27, 2012
I work for a Wireless ISP and the device impacted is the back haul radio into the site. I have swapped from a 2950T to a 3550. Replaced the radio, PoE, patch lead. We have re ran the cable up the tower using shielded outdoor cable with a drain wire which has been earthed to an earthing block in the cabinet. We have other devices on the tower not experiencing the issue. We suspect cable interference however am now at a loss to diagnose further.
[Code]....
View 3 Replies
View Related
Jan 31, 2012
Currently our Cisco 3750 have one interface (port 1) that connected to our provider (Internap) with the IP 66.150.7.68 assigned. Now we want to upgrade to dual handoff L3 protocol. Below is the network configuration from Internap.
>>>> We have assigned the below /30s for each of the interfaces and will statically route the 66.150.7.0/25 down both interfaces.
>>>>
>>>>
>>>> 63.251.162.20/30
>>>> 63.251.162.21 - border1.sef003 - Internap side
>>>> 63.251.162.22 - your side
>>>>
>>>> 63.251.162.184/30
>>>> 63.251.162.185 - border2.sef003 - Internap side
>>>> 63.251.162.186 - your side
tell what command lines do I need to input on my Cisco switch for port 1 and 2 in order for the dual handoff to work correctly?
View 1 Replies
View Related
Mar 12, 2013
I have this Cisco 1941 router with two Ethernet ports g0/0 and g0/1. The g0/0 is connected to office LAN with internet access. As my office LAN is DHCP, it will assigned a IP address for g0/0 since this g0/0 is configured as "ip address dhcp". Now my question is that i have a group of 5 pcs, namely PC1, PC2, PC3, PC4 and PC5 that is connected to the switch and one of the ports of this switch is connected to g0/1 of Cisco 1941. Is it possible that let say PC2 and PC3 (both DHCP enabled) could access the internet access from g0/0 and at the same time, the office LAN assigned IP address for PC2 and PC3 automatically?
Office Lan with internet access (DHCP) (Default gateway 10.0.0.1)
|
|
g0/0 (DHCP enable) (DHCP assigned IP address 10.0.0.138)
Cisco router 1941
g0/1
|
|
HP Switch
|
PC1 PC2 PC3 PC4 PC5
Is this operation possible? if possible, how to configure inside the router 1941 to achieve this objective?
View 8 Replies
View Related
Oct 15, 2012
I have just set up my Cisco 1941 router to my cable internet connection. I have access to everything, but I cant login successfully into Cisco CP.
I set up a new user with level 15 privileges and a secret password. I go to login via webbrowser and I put in my credentials, but I get rejected. I have tested the username and password via the CLI, and it works fine, I just cant seam to login to Cisco CP.
View 2 Replies
View Related
Nov 26, 2012
I've got a 1941 router that keeps on rebooting by itself every minute. currently, there's no power issue.
I've detected the show version returned a bus error. Is this an IOS bug?
ROUTER uptime is 1 minute
System returned to ROM by bus error at PC 0x222FE2D4, address 0xD0D0D71 at 14:27:13 SGT Tue Nov 27 2012
[Code].....
View 1 Replies
View Related
Sep 11, 2012
I have a strange behavior and a simple proble . I configured the following static route
ip route 10.84.22.0 255.255.254.0 10.84.23.254
That I advertsied in eBGP :
router bgp 65000
network 10.84.22.0 mask 255.255.254.0
the IP next hop 10.84.23.254 is cascaded on my customer LAN . At nominal time the router advertsed the route in BGP
pjnb1376#sh ip bgp nei 57.213.169.169 ad
Next Hop Metric LocPrf Weight Path
*> 10.84.22.0/23 10.84.23.254 0 32768 i
When the lan interface of the router goes down , the router still advertise the route !!! Even if the IP next hop
10.84.23.254 is not reacheable anymore ....
The box is a Cisco 1941 using
1900-universalk9-mz.SPA.151-4.M1
View 17 Replies
View Related
Feb 15, 2012
I have been having following situation on my WAN facing interface on Cisco2911 where the same number of broadcast, multicast and unknown protocol drops is happening. Not sure but some applications are struggling to run over on the WAN.
[code]....
View 4 Replies
View Related
Mar 12, 2012
I am having an issue accessing the internet from a PC on the LAN. I have configured the PC with the gateway of the router infront of the ISP to test. I can ping from the router to google or any other internet IP. From the PC I can ping to the GIG0/1 (Inside LAN IP) and the GIG0/0 (Outside WAN IP going to ISP) but I can't ping the Next Hop IP of the ISP or anything past that. If I do a trace route from the PC to the google IP address it hits the GIG0/1 Inside LAN IP Address but fails from there. Here is a cut down snap shot of the router configure
[code]....
View 6 Replies
View Related
Feb 12, 2012
I have a Cisco 1941 router configured using Cisco Configuration Professional... SSH management works from the LAN IP 10.0.1.254 and 10.0.2.254 Also, SSH management works from the LAN using the external domain name which resolves to the public IP address.
The problem i have is if I try SSH from the internet to the public IP.. nothing happens.
cisco1941#show config
Using 18498 out of 262136 bytes
!
! Last configuration change at 13:57:49 PCTime Tue Feb 14 2012 by admin
[Code].....
View 2 Replies
View Related
Sep 6, 2012
im having trouble setting up a vpn for a 1941 router this is what I have setup
crypto isakmp policy 10
encr aes 256
authentication pre-share
crypto isakmp key ########## address 63.247.48.50
[code]....
my whole problem comes about when i need to Nat 192.168.1.0 to 10.12.14.0/24 before it goes through the tunnel.
View 1 Replies
View Related
Mar 5, 2013
I bought a secondhand small business router (model 1941 Integrated Services Router) for personal use. It runs version IOS 15.0(1)M1 software, which seems to work well, but I'd like to download a firmware update that addresess some of the security flaws in this software. When I tried the download process it told me I need to buy a service contract first? Is this right, or am I doing something wrong?
View 1 Replies
View Related
Oct 10, 2012
I did have a router cisco 1941 but can not do ipsec with it,i did take a smart net.
View 3 Replies
View Related
Aug 9, 2012
I’m looking for some specific parameters of Cisco 1941 and not able to find them .
1. Maximum number of DHCP clients2. Maximum number of DHCP pools3. Maximum number of V LANs on trunk port.
View 2 Replies
View Related
Apr 4, 2013
Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
View 2 Replies
View Related
Feb 22, 2012
I have a 1941W that has a connection to my ISP (Gi0/1) and another connection to a remote lab (Gi0/0). Everything is working fine how it is setup. All my traffic from my internal networks can access the Internet and devices on the 192.168.201.0 /24 can access the Internet and the lab 10.89.0.0/16.
Now I want to have two devices (192.168.201.51 & .147) use Gi0/0 when accessing host 63.85.190.67. There is no route to this subnet since it reside in the remote lab. Here is what I have right now. How would I setup a PBR to have those two host use Gi0/0 when accessing 63.85.190.67
interface Vlan192
ip address 192.168.201.1 255.255.255.0
ip nat inside
ip virtual-reassembly (code)
View 12 Replies
View Related
