Cisco Switching/Routing :: No IP Forward-protocol UDP In 2960?
Jul 10, 2012I am trying to enter this command in Cisco 2960 but the device is not accepting it. Is this because of IOS or this command is not available for 2960?
View 1 RepliesI am trying to enter this command in Cisco 2960 but the device is not accepting it. Is this because of IOS or this command is not available for 2960?
View 1 RepliesAt a college I'm trying to setup a Cisco 2960 to be used on a VLAN 248 tagged on the uplink port that uses Spanning Tree/. Here is the following from the Cisco:
show interfaces trunk
Port Mode Encapsulation Status Native v lan
Gi0/1 on 802.1q trunking 1
Port V lans allowed on trunk
Gi0/1 248
[code]...
On the Alcatel OS6850-48L the following is setup: bridge 1x1 248 priority 3287 Vlan 248 802.1q 5/8 "cisco"
I cannot make a change on the Alcatel, I can only administer the Cisco. I was able to get things working fine (as a test) using a Net gear or HP switch instead of the Cisco. However we have a Cisco switches and would not like to have to buy HPs. Is there a compatible spanning tree protocol to use on the Cisco with the way things are configured on the Alcatel. I need to stick to standard RSTP (802.1w) ieee standards and not something Cisco proprietary.
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies View RelatedI have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies View RelatedI have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
On SW2:
*Mar 1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar 1 00:57:00.711: AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar 1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar 1 00:57:02.303: AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
[code].....
lets you catalyst 3560 & 2960 remote login with a secure protocol
View 4 Replies View RelatedI have an environment where i have two nexus 7010 switches, along with 2 nexus 5510's. I need to run OSPF as a layer 3 routing protocol between the vpc peer links. I have 1 link being used as a keep alive link, and 3 other links being used as a VpC link.
1) Is it best to configure a separate Vpc VLAN i.e 1010
2) Is it best to configure a vrf context keep-alive
3) just have the management address as the peer ip's.
I have bought Cisco ISR 881 C880DATA-UNIVERSALK9-M with c880data-universalk9-mz.150-1.M7.bin ios.
command "show ver" tell me:
License Information for 'c880-data'
License Level: advsecurity Type: Permanent
Next reboot license Level: advsecurity
So I have advsecurity. On cisco site there was a thing URL
"Table 5. Cisco IOS Software Features on Cisco 880 Series: Advanced Security Feature Set (Default)"
that tell me I have RIP protocol to use. But when I type "router rip" command and sub router sommands like: network, passive-interface, redistribution. There are no in runnning-config such things after all I've done. It have not been saved.
then the command "show licence":
#show license
Index 1 Feature: advipservices
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
I need even RIPv2 to have simple routing information to exchange.
And I don't know. Cisco 880 series is G2 or G1. Cisco ISR beginning from 890 series is G2. About 880 I don't know. There no informanion about it or at least I have not found it yet. On one 891 is the same problem. When I type "router eigrp 1" everything is great. But when "router rip" - do no work.
I have encounterd a broplem on my Cisco 805 model.
When i use the command "show ip interface brief" the status shows "up" but the protocol is "down" on my serial interface.
The link between my to sites is down after this happend.
When I config BGP on my 3750X Switch, it show error as below:
protocol not in this image
should I need to upgrade the IOS or Where I can found a supported image (support BGP)
I am trying to review the port-channel configuration on a 6500 series. I am issuing the "show etherchannel summary" command and the out put shows the Group, Port-Channel, and Ports. It does not show me the protocol that is in use such as PAgP or LACP. Does this have to do with the Etherchannel in the "On" mode rather than "active", or "Auto"?
View 2 Replies View RelatedI have configured SPAN in cisco 3750 switch as below mentioned. but the destination port protocol is down.switch(config)#monitor session 1 source interface gigabitethernet1/0/1switch(config)#monitor session 1 destination interface gigabitethernet1/0/11 ingress vlan 1
View 8 Replies View RelatedOn our backbone (Cisco 6509) we have the following config.
spanning-tree mode rapid-pvst
spanning-tree extend system-id
spanning-tree vlan 1-200 priority 24576
1. is rapid-pvst the best spanning tree protocol to use? on some switches we have pvst (not rapid)
2. do all switches in the LAN need to use the same protocol?
3. does line 3 :priority 24576 mean that someone set tis switch as root manually? how can one further enforce the backbone as root (so noone adds a old switch with lower root id)
I'm trying to implement the UDLD protocol (Cisco-compatible), but face some problems. There is no enough information for implementing this protocol neither in RFC 5171 [URL] nor on [URL] How can I get a more detailed information regarding protocol state machines and timers?
View 2 Replies View RelatedWe are using CISCO LMS 4.2.3 in our network in India, we are facing a issue regarding alarm generation for a protocol flap/down, especially when BGP / OSPF neighbourship got flapped.These flapping will result in the data service degradation , by which we came to know that some protocol flap may occurred at router end & then we go for the manual check by login into the router.after escalating the same to cisco we came to know that it is a bug of Cisco LMS. using any other method/technique to view the protocol down alarms automatically for cisco routers.
View 1 Replies View RelatedI want to configurate Vpdn protocol PPOE but i can not write protocol ppoe under vpdn group name on cisco 2811. cisco 2811 iso is 12.4 T adventurer and i upgrade it 15.1 advansecure but problem is still.
View 5 Replies View RelatedWill Resilient Ethernet Protocol (REP) run on all Cisco switches (2960S and 3010) or is it only available on Service Provider switches like the ME3400E?
View 2 Replies View RelatedI work for a Wireless ISP and the device impacted is the back haul radio into the site. I have swapped from a 2950T to a 3550. Replaced the radio, PoE, patch lead. We have re ran the cable up the tower using shielded outdoor cable with a drain wire which has been earthed to an earthing block in the cabinet. We have other devices on the tower not experiencing the issue. We suspect cable interference however am now at a loss to diagnose further.
[Code]....
Currently our Cisco 3750 have one interface (port 1) that connected to our provider (Internap) with the IP 66.150.7.68 assigned. Now we want to upgrade to dual handoff L3 protocol. Below is the network configuration from Internap.
>>>> We have assigned the below /30s for each of the interfaces and will statically route the 66.150.7.0/25 down both interfaces.
>>>>
>>>>
>>>> 63.251.162.20/30
>>>> 63.251.162.21 - border1.sef003 - Internap side
>>>> 63.251.162.22 - your side
>>>>
>>>> 63.251.162.184/30
>>>> 63.251.162.185 - border2.sef003 - Internap side
>>>> 63.251.162.186 - your side
tell what command lines do I need to input on my Cisco switch for port 1 and 2 in order for the dual handoff to work correctly?
I'm trying to upgrade NBAR protocol pack on my Cisco 1941 router, so i downloaded new NABR protocol pack (version 4.0.0) and transferred it into router flash via tftp. When i try to apply new protocol pack with command : ip nbar protocol-pack flash:[protocol-pack-name]
i got this error :
% NBAR Error : Advanced Protocol Pack can not be loaded on top of Standard Protocol Pack
The router is running IPBASE IOS with Security License, IOS image is c1900-universalk9-mz.SPA.153-1.T.bin. Does NBAR2 packages works on IO BASE images?
I have been having following situation on my WAN facing interface on Cisco2911 where the same number of broadcast, multicast and unknown protocol drops is happening. Not sure but some applications are struggling to run over on the WAN.
[code]....
I have a server that I lease that is hosted at a datacenter. Our company is going to lease a half rack and put our own equipment in it as well as a disaster recovery site. The problem is that the one server I mentioned has SQL on it and we have applications that were devloped in house ages ago that hit that SQL instance. Those applications are hard coded to the IP address of that server. We could just change it in the code, but the source code for one of the applications have disappeared over time. Now that you know my situation, my question is this. Can I make a NAT rule or something that says when traffic is destined for xxx.xxx.xxx.123, to re-routes it to xxx.xxx.xxx.321? Currently our endpoint device here is a Cisco UC520. The other end we have no control over.
View 2 Replies View RelatedI have a server that I lease that is hosted at a datacenter. Our company is going to lease a half rack and put our own equipment in it as well as a disaster recovery site. The problem is that the one server I mentioned has SQL on it and we have applications that were devloped in house ages ago that hit that SQL instance. Those applications are hard coded to the IP address of that server. We could just change it in the code, but the source code for one of the applications have disappeared over time. Now that you know my situation, my question is this. Can I make a NAT rule or something that says when traffic is destined for xxx.xxx.xxx.123, to re-routes it to xxx.xxx.xxx.321? Currently our endpoint device here is a Cisco UC520. The other end we have no control over.
View 2 Replies View RelatedMy Company use Core Sw 4507R-Sup 7L-E with Enterprise Services License. I has upgraded to use iOS cat4500e-universal.SPA.03.03.01.SG.151-1.SG1.bin
When I use match protocol in class-map, there are only about 10 protocols, and not have those ones I need. I intend to expand the list of protocols to do some Policy-map by loading PDLM. But 4507 is no longer support NBAR. So do we have another way to set Catalyst 4507R with Sup 7L-E recongnize more protocols in match protocol command?
Is there a possibility to transfer files between two N5k's via mgmt0 using TFTP protocol?
Source: One N5k's mgmt0 interface
Destination: Another Nk5' mgmt0 interface
I know when issuing "copy bootflash tftp" or vice versa, I need to specify management VRF. But how do I specify to be TFTP itself sourced from mgmt0 interface in NX-OS? From IOS I was used to use "ip tftp source-interface <interface>", but in NX-OS I have only Ethernet or Loopback as an option.
According to NX-OS Unicast Routing Configuration Guide (Configuring Layer 3 Virtualization) the answer should be in N7k configuration guide, but I didnt find it there either...
We are using 3825 Cisco router with IOS version 12.4(24)T2. The unknown protocol drops on our GigabitEthernet0/1 interface is increasing. This interface is connected to our modem. What could be causing this unknown protocol drops?
cnshaccent-gw-2#sh int GigabitEthernet0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is ffff.ffff.ffff (bia ffff.ffff.ffff)
[Code]....
I'm trying to forward ports for SQL and VNC using these commands in the CLI:
ip nat inside source static tcp 192.168.1.150 5900 interface GigabitEthernet0 5900
ip nat inside source static tcp 192.168.1.150 5800 interface GigabitEthernet0 5800
ip nat inside source static tcp 192.168.1.150 1433 interface GigabitEthernet0 1433
where 192.168.1.150 is my server (that hosts SQL server and that I want to be able to connect to remotely using VNC) and GigabitEthernet0 is my configured WAN interface.
When I try to connect from an external client I get the error: "Failed to connect to server..." Is this a firewall issue? How do I get round it? The 819 is the only router/firewall in my network.
I need to forward port 2875 from any public address to an internal address 192.168.20.103. I am not getting something right because it will not work. Below is my config.
Current configuration : 11012 bytes
!
! Last configuration change at 23:30:24 UTC Fri Apr 12 2002 by cisco
!
[Code]....
I have a 3845 router. Setup SSH Version 2generated rsa keys (1024)set login localtransport input ssh and telnet is enabled since I can't get ssh connection working When I connect using SSH, I get the following error. server refused authentication protocol.
View 21 Replies View RelatedWe have one core switch and we are planning to add a 6509. Both are none VSS.All the access switches are Catalyst 3560 series.
We plan to have all 3560s to have a link to each of the core. Without VSS, it is not possible to etherchannel to both core switches correct?What protocol should I configure to prevent in case one core fails? HSRP, VRRP, GLBP?
Do I need to run spanning tree protocol? if so which one?What is the best way to connect from each Catalyst 3560 for load balancing and redundancy? One to each core?
we have a 2800 series router functioning as our internet router and it will only forward packets to addresses with host entries in the routing table even if the network is directly connected.
View 18 Replies View RelatedI need getting access to my http server. I have a host name that I configured to point to my IPS IP address. Port 80 is enabled on my server, but I can't seem to get access it from my web address [code]
View 5 Replies View RelatedI have some questions about how to configure my Cisco 1941 with a routed subnet from my ISP to forward them to 1 or more servers in my LAN.1 Routed subnet /29 from my ISP (over a fiber connection).In my LAN I have (at the moment) 3 servers, and about 15 clients.I would like to use the first ip address from the routed subnet for internet traffic from all the clients in the LAN.I would like to use the second ip address from the routed subnet for server1 so that server1 accept some allowed connections and that server1 connects to the internet with the second ip address from the routed subnet
I would like to use the thirth ip address from the routed subnet for server2 so that server2 accept some allowed connections and that server2 connects to the internet with the thirth ip address from the routed subnet.I would like to use the fourth ip address from the routed subnet for server3 so that server3 accept some allowed connections and that server3 connects to the internet with the fourth ip address from the routed subnet.[code]