Cisco Switching/Routing :: UC520 / Forward One IP To Another?
Jun 18, 2011
I have a server that I lease that is hosted at a datacenter. Our company is going to lease a half rack and put our own equipment in it as well as a disaster recovery site. The problem is that the one server I mentioned has SQL on it and we have applications that were devloped in house ages ago that hit that SQL instance. Those applications are hard coded to the IP address of that server. We could just change it in the code, but the source code for one of the applications have disappeared over time. Now that you know my situation, my question is this. Can I make a NAT rule or something that says when traffic is destined for xxx.xxx.xxx.123, to re-routes it to xxx.xxx.xxx.321? Currently our endpoint device here is a Cisco UC520. The other end we have no control over.
View 2 Replies
ADVERTISEMENT
Apr 11, 2012
I have a server that I lease that is hosted at a datacenter. Our company is going to lease a half rack and put our own equipment in it as well as a disaster recovery site. The problem is that the one server I mentioned has SQL on it and we have applications that were devloped in house ages ago that hit that SQL instance. Those applications are hard coded to the IP address of that server. We could just change it in the code, but the source code for one of the applications have disappeared over time. Now that you know my situation, my question is this. Can I make a NAT rule or something that says when traffic is destined for xxx.xxx.xxx.123, to re-routes it to xxx.xxx.xxx.321? Currently our endpoint device here is a Cisco UC520. The other end we have no control over.
View 2 Replies
View Related
Sep 9, 2012
Let me start with some infrastructure details ...
Cisco C2901 as our Main Router
Cisco UC520 as Communication Platform
Cisco C3560x as Core-Switch
VLAN 10 : Data
VLAN 100 : VOICE
Everything is working but i m not sure if the switchport config is right in that way.
As an example :
interface GigabitEthernet 0/6
switchport access vlan 10
switchport mode access
switchport voice vlan 100
spanning-tree portfast
When we connect an Cisco 7971g and an pc everything is working fine. But when i start wireshark on the pc behind the phone you see a lot of UDP Traffic source UC520 destination 239.10.16.8 or 239.10.16.16. At this point i m getting confused. So i start looking for the cisco phone config, VLAN ID on the phone is 100 (i think that is ok) but the PC-VLAN part is empty?
The main thing is, how can i stop this cisco-sccp traffic on the pc port (prtg shows me a average of 200 kbit/s) i think it is an config fault.
View 4 Replies
View Related
Aug 27, 2012
I have a sge2000p to install with a uc520. I have all data traffic passing ok but voice will not work. Phones to not get ip etc.
View 4 Replies
View Related
Aug 15, 2012
I'm trying to forward ports for SQL and VNC using these commands in the CLI:
ip nat inside source static tcp 192.168.1.150 5900 interface GigabitEthernet0 5900
ip nat inside source static tcp 192.168.1.150 5800 interface GigabitEthernet0 5800
ip nat inside source static tcp 192.168.1.150 1433 interface GigabitEthernet0 1433
where 192.168.1.150 is my server (that hosts SQL server and that I want to be able to connect to remotely using VNC) and GigabitEthernet0 is my configured WAN interface.
When I try to connect from an external client I get the error: "Failed to connect to server..." Is this a firewall issue? How do I get round it? The 819 is the only router/firewall in my network.
View 15 Replies
View Related
Feb 13, 2012
I need to forward port 2875 from any public address to an internal address 192.168.20.103. I am not getting something right because it will not work. Below is my config.
Current configuration : 11012 bytes
!
! Last configuration change at 23:30:24 UTC Fri Apr 12 2002 by cisco
!
[Code]....
View 5 Replies
View Related
Jul 10, 2012
I am trying to enter this command in Cisco 2960 but the device is not accepting it. Is this because of IOS or this command is not available for 2960?
View 1 Replies
View Related
Jan 1, 2013
we have a 2800 series router functioning as our internet router and it will only forward packets to addresses with host entries in the routing table even if the network is directly connected.
View 18 Replies
View Related
Apr 18, 2012
I need getting access to my http server. I have a host name that I configured to point to my IPS IP address. Port 80 is enabled on my server, but I can't seem to get access it from my web address [code]
View 5 Replies
View Related
Feb 13, 2013
I have some questions about how to configure my Cisco 1941 with a routed subnet from my ISP to forward them to 1 or more servers in my LAN.1 Routed subnet /29 from my ISP (over a fiber connection).In my LAN I have (at the moment) 3 servers, and about 15 clients.I would like to use the first ip address from the routed subnet for internet traffic from all the clients in the LAN.I would like to use the second ip address from the routed subnet for server1 so that server1 accept some allowed connections and that server1 connects to the internet with the second ip address from the routed subnet
I would like to use the thirth ip address from the routed subnet for server2 so that server2 accept some allowed connections and that server2 connects to the internet with the thirth ip address from the routed subnet.I would like to use the fourth ip address from the routed subnet for server3 so that server3 accept some allowed connections and that server3 connects to the internet with the fourth ip address from the routed subnet.[code]
View 13 Replies
View Related
Nov 16, 2011
Cisco LMS 4.0: Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address? • Traps contain the original Device Agent IP to identify the source (Not the IP of LMS)?• Is possible to configure one logical IP address or Domain Name for redundant LMS:Cisco Security Manager 4.1:Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address?• Traps contain the original Device Agent IP to identify the source (Not the IP of Security Manager)? • Is possible to configure one logical IP address or Domain Name for redundant Security Manager?
View 0 Replies
View Related
Jan 5, 2012
I have a cisco 1841 and I am hooking up some cameras onto my network. My global IP is 64.190.170.2 and my internal IP which is going to my cameras DVR is 192.168.1.15. I need to be able to forward port 8080 from my global IP to my local IP so i can view my DVR remotely. What is the command i need to put in my Cisco 1841 to forward this port?
View 2 Replies
View Related
Aug 9, 2012
I have some Ethernet-connected cameras that all have the same Ethernet MAC address FF:FF:FF:0A:0A:0A. They were originally designed to directly connect to a Windows PC, but they can also connect through a simple unmanaged switch.A Catalyst 3560 switch won't forward packets to or from anything with that MAC address, at least not by default. Is there a way to convince the switch to do so?
It was my hope to replace the dedicated connections we have for these cameras with a separate VLAN for each camera, and switch them through our existing switch network. Given that all of the cameras use the same MAC address, putting them on the same network is out of the question, but different VLANs, where the only two devices on each VLAN were the camera and the PC that uses it, would be fine.
The switches run IOS 12.2(55) SE through SE3. I learned the camera MAC address from the PC's ARP table while the camera software runs; it turns out the cameras don't have a full IP stack either and don't even do ICMP.
View 2 Replies
View Related
Dec 5, 2012
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies
View Related
Mar 29, 2012
I faced with issue on ME3800. [code] With that configuration there is no problem with DHCP Relay packets.But if I add on interface #xconnect 82.199.1 19.1 77 encapsulation mpls it will stop forward DHCP relay packets immediately. All other traffic transfers without problem.
View 2 Replies
View Related
Oct 26, 2011
We bought Cisco sup engine WS-SUP32-GE-3B for 6500 switches 2 nos for redundancy. I have connected 6 systems on each sup engine ports. How to clarify whether both sup engine will forward the data while one is Master and other is standby?
View 4 Replies
View Related
Apr 8, 2011
We have Cisco UC520 Router, We are facing Network problem in our Office due to high memory & CPU Uses of UC520, sometime 100% CPU Used of UC520 and we have lossed internet access from Router from last two day's, all was going well before two day's, we haven’t had this happen before Last Thursday, but when I reboot router it's working again
coinop-uc520#sh proc cpu his
coinop-uc520 02:38:41 PM Saturday Apr 9 2011 WST
111112222211111
[Code]....
View 1 Replies
View Related
Jul 25, 2012
Have an issue where have two locations trying to get connected. first location has a cisco 861 and a uc500 for the phone system. The second location is using a UC520 for the phones and as the router. Below are the configurations of the 861 and the UC520.
Cisco 861
Current configuration : 7635 bytes
!
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
View 2 Replies
View Related
Jan 6, 2011
I am constantly getting error on UC520W Wifi from last Night, I am not getting with this error. What is the cause of this error, or is there any issue on UC520. [Code] .........
View 12 Replies
View Related
Jul 11, 2011
I am trying to setup time service on two devices. Once is a UC520, the second an 1840 router. I would like to use the FQDN of the time server which is north-america.pool.ntp.org. This is the recommended procedure as per ntp.org due to changes of IP addresses of time servers.
On the UC520 this is not a problem. I type in "ntp server north-america.pool.ntp.org" and this is how the command stays in the config. On the 1800 the FQDN is resolved and inserted into the config as an IP address. This works for now but kinda defeats the purpose of using a FQDN.
How can I keep the 1800 from converting to IP?
View 2 Replies
View Related
May 17, 2012
I've configured in an UC520 a SSL VPN.I can access properly and I can see the labels, but I only can access urls which are http, not https:I can access the default ip of the uc520 (192.168.1.10) but When I try to get access to a secure url I get the msg: Failed to validate server certificate I'm trying to access a Cisco Digital Media Manager, whose url is URL Does the certificate of both hardware has to be the same?
View 7 Replies
View Related
Oct 15, 2012
I am not an expert at routing but was wondering what the most cost and time effective way to have an ip request return with another ip address from outside the WAN of the router. Specifically want to have an application request for example 192.168.1.121 and have 173.194.43.41 respond and communicate with the application instead. To make it a bit more interesting I'd like actually to set a table or config file to point to a domain name (url) which gets resolved as an ip address. (Port independent) To get a better understanding: one example might be typing in 192.168.1.121 in a browser and googles search engine comes up on the browser.
another example might be typing in 192.168.1.121 in an ftp client and it hooks to an ftp server on the other side of the world which resolves to ftp.this-is-a-test.com.Make sense? I was looking at openwrt and tomato a little but I don't think I have such a complete grasp on how to do it in general. Being that it seems they are 2 different layers of the network model, I was told it can't be done but I don't know if I can believe that yet. Either by third party software orreprogramming the router or adding another device to the network, I have a feeling that it seems like such a simple redirection that it can be done somehow
View 6 Replies
View Related
Feb 2, 2013
So I need to forward certain ports to play/log-in game:
TCP: 80, 443, 2099, 5222, 5223, 8393-8400
UDP: 5000:5500
I did forward them in my router and checked them with PFPortChecker, every port seems to open except 2099, I don't understand why.Note that I disabled Windows Firewall, Router's Firewall, and I'm using Kaspersky Internet Security which I disable while checking ports/logging to game
View 19 Replies
View Related
Aug 15, 2011
I'm trying to forward ports for game connections. For this particular game, I'm trying to forward port 7777My ports aren't forwarding according to: Open Port Check Tool - Test Port Forwarding on Your Router and Open Port Check Tool[CODE]
View 13 Replies
View Related
Sep 19, 2011
i want to open portforward to utorrent in arouter but i cant open the addres of the router lookand when i go to local area connection status /status/detailsi found number of ip but there is no gateway i take whole ip and put them in browser and its dont open but the last friday i wake up in 3am run cmd and put ipconfigi found the gateway 192.168.2.45put it it in browser its open want username and pass i know them but i see lets doit next day going to bed next day the gate way reverse to the stupid gateway in in the pic i cant use aprogram to open port as i cant knowing my router mode
View 1 Replies
View Related
Jul 11, 2011
My cisco 837 is connected to a ADSL Router by Ethernet Cable. I have forwarded the telnet port from my ADSL Router to the LAN IP of the Cisco Router so that i can connect to it Remotely but it is not working. I am able to telnet internally but from Internet it is not working. I am not using Cisco Router for ADSL Connectivity.
View 5 Replies
View Related
Apr 1, 2013
when dealing with NATing with port fowarding from a specific IP range on the outside to a inside IP address. Here is what I have now:Cisco 3640 WAN Router: [code]
which ofcouurse did not work and ASA did not respond to 443 on either Anyconnect or HTTPS. Nothing showing in"show ip nat translations" for the incoming traffic from “ip nat outside source static tcp 15.236.10.0 192.168.4.2” and “ip nat inside source static tcp 192.168.4.2 15.236.10.0”
View 1 Replies
View Related
Jan 2, 2011
I have just purchased a nas drive. I want to be able to access my files from anywhere. I believe if i setup FTP i can view the files over the web. from what i have been told i need to forward port 21 to the ip address of the nas drive.
View 6 Replies
View Related
Jul 4, 2011
ASA5510 configuration, I would like to know if it is possible (and how) to forward traffic received on WAN port of the first ASA to the server in LAN on the other side of VPN tunnel:
Internet (IP 85.128.50.x) – ASA5510 (192.168.1.x) – VPN tunnel – ASA5510 – LAN (172.16.71.x)
I need to have IP 85.128.50.50 redirected to 172.16.71.15 through VPN?
View 1 Replies
View Related
Jul 21, 2011
I purchased a Cisco 851 Router for the reliablity, but the process to manage the router to port forward a IP address for a internet camera ... I'm lost. I will try the forums, versus paying a $400 dollar fee for support.
What is the process to have an internal IP address for my outdoor network camera visiable for WWW? How do I port forward 10.10.10.40 How do I assign a static IP to this outdoor network camera?
I can access the Cisco SDM Express V2.5
View 17 Replies
View Related
May 14, 2012
I've just bought a Cisco 887m-k9 and I am trying to forward the ports. I have a Polycom HDX H.323 device connected to it with a static IP of 10.10.10.5 (ethernet port 0).Previously I had a consumer grade Linksys router which worked fine (I simply entered ports into the GUI), but I couldn't hardcode LAN port speed so I bought this. I have the list of TCP and UDP ports which are forwarded using the following commands:
ip nat pool Polycom 10.10.10.5 10.10.10.5 netmask 255.255.255.0 type rotary
ip nat inside source static tcp 10.10.10.5 80 88.xxx.xxx.49 80 extendable
ip nat inside source static tcp 10.10.10.5 443 88.xxx.xxx.49 443 extendable
ip nat inside source static tcp 10.10.10.5 1300 88.xxx.xxx.49 1300 extendable
[code]....
Where 88.xx.xx.49 is my static IP, while 77.xx.xx.170 is my default gateway.
View 1 Replies
View Related
Sep 20, 2011
I always seem to have problems when trying to configure port forwarding on cisco routers. I've even tried the instructions I have for a cisco 1811, but no luck. I have a cisco 871 and a computer that has VNC installed on it. I want to be able to access that computer from out side the network using the external ip address and port 5950. People outside the network will be able to open vnc viewer and type in *external ip address*:5950 and it will be directed to the computer with a static internal ip address of 10.12.0.10. What commands do I use to do this?
View 4 Replies
View Related
Oct 19, 2011
I'm trying to forward a site (ex: facebook) to another ip address or site (on another computer). Just wondering if it's possible by editing settings in the router (I do not have access to the 2nd computer but it is on the network).
View 5 Replies
View Related
