I faced with issue on ME3800. [code] With that configuration there is no problem with DHCP Relay packets.But if I add on interface #xconnect 82.199.1 19.1 77 encapsulation mpls it will stop forward DHCP relay packets immediately. All other traffic transfers without problem.
I have some DHCP trouble since I subnetted my network with a 2921. My clinets are in 172.16.2.0/23 and DHCP servers are in 172.16.5.0/24.Sometimes, randomly I guess, I get NACK from my DHCP server, and if I look into DHCP logs I got something like this:
Have a client wanting to hand out public ip addresses to all clients from a PFSense Firewall terminating the internet connection.
How do I allow the Cisco Switches currently in place, configured with private ip addresses in the 10.10.x.x ranges and Vlans, where the main 3550 layer 3 has defined dhcp scopes for each vlan, to relay dhcp requests from all vlans to the PFSense firewall?
I assume I would take off the currently defined dhcp scopes for the vlans and configure each vlan/switch with the ip helper address and specify the PFSense firewall and that Nat would have to be disabled onthe firewall?
I need to get some low volume, interactive data, prioritized on frame relay PVCs across our network. I have followed the CBWFQ examples from cisco.com, but my test packets are still showing latency over 1 second. My lab set up has a corporate connected gateway router linked via FE to testrouter 50. TR51 has a T1 frame relay loop to another router acting as a frame relay switch. The other side of the FR switch has a 56k link to testrouter51. I am sourcing test pings from my desktop PC, that are marked as AF43, and leave at a rate of 1/second, when the response comes back in time. I am using a Smartbits to generate some default class traffic at a rate of about 56Kbps only in the 'outbound' direction, toward TR51, as this emulates a file copy from corporate to remote sites, that is causing the AF43 traffic to suffer. Here is the relevant config on the TR50 device:
class-map match-all rtu-data match ip dscp af43 ! policy-map frame-56 class rtu-data priority percent 20 class network-mgt-data bandwidth percent 5(code)
I have some Ethernet-connected cameras that all have the same Ethernet MAC address FF:FF:FF:0A:0A:0A. They were originally designed to directly connect to a Windows PC, but they can also connect through a simple unmanaged switch.A Catalyst 3560 switch won't forward packets to or from anything with that MAC address, at least not by default. Is there a way to convince the switch to do so?
It was my hope to replace the dedicated connections we have for these cameras with a separate VLAN for each camera, and switch them through our existing switch network. Given that all of the cameras use the same MAC address, putting them on the same network is out of the question, but different VLANs, where the only two devices on each VLAN were the camera and the PC that uses it, would be fine.
The switches run IOS 12.2(55) SE through SE3. I learned the camera MAC address from the PC's ARP table while the camera software runs; it turns out the cameras don't have a full IP stack either and don't even do ICMP.
I am trying to get an understanding of some behaviour I am seeing on my N7Ks regarding DHCP relay.I have two identically configured Vlans interfaces both configured with the same two dhcp relay servers in the same order. The only difference between the two vlans is that one is HSRP active on the A side switch and the other is active on B side switch. All clients in Vlan136 (active on B side) are getting DHCP leases from the first of the two dhcp relay servers configured while all clients on Vlan 137 (active on A side) are getting DHCP leases from the second of the two dhcp relay servers. I would expect that all clients on both vlans would get leases from the first relay server configured unless that device was unavailable.
Would like to impliment VLAN's on Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(25)SEB4...But I need a DHCP Realy to my Windows Based DHCP Server. How do I enable DHCP Relay on the 3560?
I have a 2921 with 4 segments: [code] My DHCP server is 172.16.5.2 and I need to serve clients from 172.16.2.0/23 by MAC address and only to that segment.
Windows Server 2008 R2 has two DHCP scopes 192.168.1.x (for data) and 192.168.2.x (for VOIP). The Catalyst 2960-S has Vlan1 for the Data V LAN and V lan 2 for the VOIP network. How do I setup DHCP relay for Vlan2 to get their IPs from the scope on the Windows server?
Used to doing ip helper-address x.x.x.x in other Catalyst switches, but not available here.
I have upgraded a C3750G-12S-E to c3750-ipserviceslmk9-tar.122-55.SE5This switch is a distribution layer switch for one of my remote sites. it contains an ip helper-address on the site vlan's SVI.DHCP relay is no longer functioning for client PCs. Static address assignment allows full network functionality. I enabled debug ip dhcp server packet. [code] Actually I am betting you upgraded your IOS from something before 12.2(50)SE to 12.2(50)SE or later. We added enhancement CSCso19800 which will validate DHCP options when we are a relay agent.
I am trying to configure two 3845 routers to act as dhcp server and dhcp relay. Clients are connected to the router that relays all dhcp requests to the vrf instance which is used to connect it to the router wich is running dhcp server.
Router1 ip vrf dhcp_dns rd 8:1 int gi0/0 ip vrf forwarding dhcp_dns ip address 192.168.200.5 255.255.255.248
[code]...
So far I can see dhcp requests coming from the R1 and dhcp server on R2 replies with the dhcp offer but PC is not getting any ip.
How to configure cisco 3560 to force the client only can get ip by dhcp-relay server ?
The company i am working in has 5 vlans which have been set an lay-3 switch(3560), uses the dhcp-relay server .(in svi configuration: ip helper-address X.X.X.X) well , that works ok~
Now , I got my problem: I need to force the client only can get ip by dhcp-relay server, that means if anyone set static IP manunally , he can't really access to anywhere (to provent anyone set static IP with malignancy )
I know if a h3c router , how to set this configuration n svi configuration : dhcp relay security address-check enable ) the how to configure on a cisco 3560 ?
I am trying to block all dhcp packets through 2960S lan base IOS. But when i set no trust interface for dhcp snooping, the dhcp packet source port will be err-disabled. Is there any other solution to block any DHCP packet through switch without interface or other service outage?Is possible to block DHCP packet through specific VLAN?
I recently installed DHCP snooping on a 3750v2 switch (Version 12.2(55)SE4) and configured the uplink(Po2) as a trusted port. The problem is that clients cannot receive an IP address. When I disable DHCP snooping it is working properly. DHCP snooping is configured correctly but I don't have an idea how to resolve it. [code]I tested the solution on the same kind of hardware switch and firmware and it worked out fine. What is causing the clients not to receive an IP address from the DHCP server?
I am migration an IPsec site to site VPN config to a new ASR1001 router «facing» a Linux box (ipsec-tools + racoon). As the Debian Linux does not offer VTI, I am using a crypto map.
The working config is given below with the corresponding logs on the Linux side.
When I try to apply this previously working config to the ASR1001, I get the following error :
i'm trying to connect a picaxe microcontroller to my friend's coffee machine for a school projet. eventually i realised i had 4 options
1:get arrested by the police (long story) 2:lay out 5km of cable dorchester,dorset,uk 3:end up using a REAL pickaxe on my phone 4:pay £100 for a picaxe server 5:intergrate the ethernet into a picaxe microcontroller
the only problem is that you need a very fast processing speed for ethernet,unless you were to use <1mbs ethernet?is there a device witch will only relay packets at <1mbs Ethernet
I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
First step: enable multicast routing
Second step: on both interfaces (Fe 0/1 and Fe 0/2) - ip pim sparse-mode
Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
When I start VLC on computer nothing happend. If I try to connect computer on same subnet where is source of multicast streams it works fine.What I am doing wrong ? Is there anything about routing ? All subnets are directly connected. RP is not needed if I have one router or ?
I'm having a problem getting DHCP working with an ASR9k as shown in this document. I've successfully implemented very similar setups with some Cisco IOS routers, but the IOS XR on the ASR seems to be defeating me. Router A (happens to be a 3750)A DHCP/BOOTP/TFTP server, connected to router ARouter B - this is the ASR, running software version 4.0.3.Router A and B are connected by a layer-3 link.Router C (happens to be a Broadcom embedded router). It's connected to Router B by a VLAN trunk link.Device 1, this one needs to get its configuration by DHCP/BOOTP/TFTP. It's connected to Router C by a VLAN trunk link.Device 2, this one doesn't need any DHCP/BOOTP/TFTP. It's connected to Router C by a VLAN trunk link (its port is the same as Device 1's) Device 2 works great - it can ping the DHCP/BOOTP/TFTP server (and vice versa) and everything else it needs.
I have a firewall that I want acting as a DHCP relay. This firewall has a number of VLAN interfaces serving clients. The DHCP relay destination is the IP address of a Windows 2012 Server running Microsoft DHCP which has multiple scopes configured, one for each client VLAN.What I'm finding confusing is how the DHCP will identify the client. Does the DHCP relay insert an identifier of some sort (opt. 54?) based on which VLAN the DHCPREQUEST comes from and then this identifier can be configured to be recognized on the DHCP server?
I have a data center with virtual desktops and other shared infrastructure serving remote sites, some of which are connected to the data center with GRE over IPsec.
IP address management including DHCP is centralized in my architecture, but I simply cannot figure out how to relay DHCP requests through GRE over IPsec to my DHCP server cluster. I am working with Cisco 800 series VPN peers, and the VPNs are terminated either on a 1841 or a Juniper SRX. Everything else is just fine and dandy, but DHCP is not forwarded across the GRE tunnel.
As a workaround I am forced to use local DHCP pools on the VPN peers, which is extra work from a management point of view, and also precludes static IP address assignment where a local DHCP pool is in a VRF. My LAN devices are mostly thin clients, so I don't care if DHCP stops working when the WAN link fails. As such local pools have no upsides, they are only a tremendous hassle.
My config is very basic, public WAN in global routing table and WAN + GRE tunnel in a VRF. NAT is not used. Here are the DHCP-related configs I have tried:ip helper-address on the LAN gateway, both with and without ip forward-protocol udp bootpcip dhcp pool with relay options configured
In every case, I can see the UDP broadcasts hit the LAN gateway, but relayed packets never arrive at the other GRE tunnel endpoint let alone the DHCP server.
I have defined several V LAN's and the corresponding IP Addresses on the SGE2000. The static routing works fine. On one V LAN there is a Windows 2003 DHCP Server which I have defined as DHCP Relay Server (Option 82), but no packets are relayed. Has anyone a functional setup, with dhcp relay?
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
DHCP Relay on a SGE2000 switch.I have configured two VLANs on the switch, VLAN2 (192.168.10.x/24) and VLAN3 (192.168.9.x/24). I have the switch in Layer 3 mode. I have configured the DHCP relay server of 192.168.10.4 and the DHCP Interfaces as VLAN3. All of the IP Static Routes were generated by the switch.
If I put a client computer on a port that is Untagged VLAN 3 and try to get a DHCP address from the server on an Untagged VLAN 2 port I never get a response back.I have done some packet captures and here is what I have found:
I see the DHCP broadcast on the client computerI see the DHCP Request on the DHCP server coming from the IP assiged to the switch on VLAN 3 (192.168.9.254)I see the DHCP server respond with a DHCP OfferThe DHCP offer never gets to the client computer I can't seem to get a DHCP address to any system not on the same VLAN as the DHCP server. Option 82 is disable and I did try enabling it, which made no difference.
My network is set up such that I have a Wireless Network in VLAN 1, which is the primary network that we use. The subnet is 10.5.1.x.
My goal is to set up a completely isolated Guest Wireless Network, however it would work best. What I am trying to do now is I created a seperate VLAN (VLAN 2, IP range 10.5.2.x) and turned on DHCP on the WRVS4400N. However, in the Guest Network, it is always picking up a 10.5.1.x IP which is handed out by the DHCP server (10.5.1.5, Win 2003) and still routing all of the traffic to/from our private network.
Here's What I have set:
Wireless>Security Settings>Guest Network (SSID 2) Wireless Isolation (between SSID w/o VLAN): EnabledWireless Isolation (within SSID): EnabledSetup>LAN>VLAN 1 Router IP 10.5.1.1, WLAN IP 10.5.1.3DHCP Relay for 10.5.1.5Setup>LAN>VLAN 2 Router IP 10.5.2.1DHCP Enabled for 10.5.2.x subnetDHCP Relay option is grayed out (not sure why)Setup>Advanced Routing Inter-VLAN Routing: Disabled Any way to solve this would be fine. I just do not want traffic routing through our internal network. Ideally, if I could get the Windows server to hand out 10.5.2.x addresses, that would be perfect, but I'm not sure how to configure it for such.
I am actually more of a 3Com guy than Cisco but I like to think I know my stuff and having just discovered this site I hope to join in as it looks a good place.I have a question about the general theroy underneath DHCP relay (IP Helper in the Cisco world I believe!)I've always put the DHCP server in VLAN1 only. A few weeks ago, I repatched the DHCP server in one of our offices (small site, single switch) into a different port by mistake. A few days ago I noticed (when doing something entirely unrelated) that I had left it in a port on both VLANs meant for PC's/phones. So, untagged on VLAN1, tagged on the voice VLAN. It had continued to work properly all that time however.By contrast, at a larger site, a new DHCP server came online and was put on a switch elsewhere in the building and was also put into a port on both VLANs - however things didn't work at all - of course we noticed immediately and changed the port setting to VLAN1 only, and it came back.In the second example, the server was on a different switch to where the main L3 switch for the Voice VLAN was (which also does the DHCP relay), and was connected over a fibre trunk link.Is there any reason why it should work on a single switch on a port on both VLANs, but not when connected over a trunk link? The server does not understand tagging. In the case where it worked, the phones were getting an IP from the correct scope; so the relay obviously must have been working with the server issuing an address based on the GIADDR field.