Cisco Switching/Routing :: Getting Configuration For C3560x And UC520
Sep 9, 2012
Let me start with some infrastructure details ...
Cisco C2901 as our Main Router
Cisco UC520 as Communication Platform
Cisco C3560x as Core-Switch
VLAN 10 : Data
VLAN 100 : VOICE
Everything is working but i m not sure if the switchport config is right in that way.
As an example :
interface GigabitEthernet 0/6
switchport access vlan 10
switchport mode access
switchport voice vlan 100
spanning-tree portfast
When we connect an Cisco 7971g and an pc everything is working fine. But when i start wireshark on the pc behind the phone you see a lot of UDP Traffic source UC520 destination 239.10.16.8 or 239.10.16.16. At this point i m getting confused. So i start looking for the cisco phone config, VLAN ID on the phone is 100 (i think that is ok) but the PC-VLAN part is empty?
The main thing is, how can i stop this cisco-sccp traffic on the pc port (prtg shows me a average of 200 kbit/s) i think it is an config fault.
View 4 Replies
ADVERTISEMENT
Jun 18, 2011
I have a server that I lease that is hosted at a datacenter. Our company is going to lease a half rack and put our own equipment in it as well as a disaster recovery site. The problem is that the one server I mentioned has SQL on it and we have applications that were devloped in house ages ago that hit that SQL instance. Those applications are hard coded to the IP address of that server. We could just change it in the code, but the source code for one of the applications have disappeared over time. Now that you know my situation, my question is this. Can I make a NAT rule or something that says when traffic is destined for xxx.xxx.xxx.123, to re-routes it to xxx.xxx.xxx.321? Currently our endpoint device here is a Cisco UC520. The other end we have no control over.
View 2 Replies
View Related
Apr 11, 2012
I have a server that I lease that is hosted at a datacenter. Our company is going to lease a half rack and put our own equipment in it as well as a disaster recovery site. The problem is that the one server I mentioned has SQL on it and we have applications that were devloped in house ages ago that hit that SQL instance. Those applications are hard coded to the IP address of that server. We could just change it in the code, but the source code for one of the applications have disappeared over time. Now that you know my situation, my question is this. Can I make a NAT rule or something that says when traffic is destined for xxx.xxx.xxx.123, to re-routes it to xxx.xxx.xxx.321? Currently our endpoint device here is a Cisco UC520. The other end we have no control over.
View 2 Replies
View Related
Jul 16, 2012
Im trying to find an affordable Cisco switch with similar capabilities and features as the WS-C3560X-48T-S (L2/L3 routing as in IP Base, dual power supply, etc.).
View 2 Replies
View Related
Jul 31, 2012
I got a pair of new C3560X-24T-S switches with C3KX-NM-10G modules, and am trying to get a long distance 10G link up using 3rd party SFP-10G-ER SFPs (XGIGA with Cisco coded IDPROMs)I've enabled use of unsupported transcievers with the following commands:service unsupported-transceiver no errdisable detect cause gbic-invalidAfter that the switches accepts the SFPs but I get no light (sh int trans shows Tx -40), but if I insert a supported SFP first and then switches to my ER SFPs I get them to start transmitting, however I still don't LINK on the interface.I've tried with both 12.2(55)SE3 (that the switches came with) and 15.0(1)SE3 with same results.I know SFP-10G-ER SFPs are not supported on these switches, but are scheduled for the 15.0(2) release, but I was under the impression that they should already work using the above commands to enable the use of unsupported SFPs.So my question is basically: Is the new code in 15.0(2) really needed to make ER SFPs work, so I should just wait for that release, or are my 3rd party SFP simply broken/un-compatible with these switches?Also, could reprogramming them to look like SFP-10G-LR SFPs, which are supported, make any difference, or should it already have worked now with service unsupported-transceiver enabled if they were compatible?
View 5 Replies
View Related
Jan 11, 2012
Currently there are three stacked WS-C3750G-24TS-1U on data centre. I am going to buy a WS-C3560X-48T-L to use 10GbE module. Is it possible stack this switch "WS-C3560X-48T-L" to current switches "WS-C3750G-24TS-1U" ?
View 1 Replies
View Related
Feb 17, 2013
I have a Switch model WS-C3560X-24P with SW Version 12.2. (55) SE5 and SW Image C3560E-UNIVERSALK9-M. Now I get messages from 3 ports that:% ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/12: PD removed. The strange thing is that there is nothing connected to these ports and they are like "notconnect»
An excerpt of the log looks like this:
1469058: Feb 18 09:08:33.945 CET: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/12: PD removed 1469060: Feb 18 09:08:49.279 CET: %ILPOWER-5-POWER_GRANTED: Interface Gi0/12: Power granted 1469061: Feb 18 09:08:50.310 CET: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/12: PD removed 1469063: Feb 18 09:09:02.280 CET: %ILPOWER-5-POWER_GRANTED: Interface Gi0/12: Power granted 1469064: Feb 18 09:09:03.413 CET: %ILPOWER-5-[Code]....
View 5 Replies
View Related
Dec 12, 2011
I have recently installed 4 3560 (WS-C3560X-48T-S) Switches. At first the switch comes up, indicating all connected ports with a green LED. Whenever i unplug a cable and plug it back in, the status LED will stay off. The same thing happens when I push the mode button and cycle throgh the different modes, i lose certain LEDs.
I'm using 12.2(53)SE2, another user reported the same issues under 12.2(55)SE1 .
View 4 Replies
View Related
Jul 5, 2012
I would I upgrade this from a LAN base to ip services?
View 2 Replies
View Related
Aug 27, 2012
I have a sge2000p to install with a uc520. I have all data traffic passing ok but voice will not work. Phones to not get ip etc.
View 4 Replies
View Related
Jan 19, 2012
Does the Cisco WS-C3560X-24P-S switch supports ip flow export?
View 1 Replies
View Related
Apr 24, 2013
I have a WS-C3560X-24 and attached to that are some 9 acces switches, for some weeks now my 3560 reboots some time what couse that the other 9 switches are down for some minuts as well and i dont want this of course. the reboot happens at random times and some times one week not and then like yesterday afternoon it rebooted again.
when i check the Flash directory there is no crash file and when i look at the logging its clean and just shows the startup. it's not the powersuply it's redundend and more L3 switches are attached to this power source and they dont reboot.
L3_AIM#sh versionCisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2011 by Cisco Systems,
[Code]......
View 3 Replies
View Related
Jul 17, 2012
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
View 1 Replies
View Related
Apr 8, 2011
We have Cisco UC520 Router, We are facing Network problem in our Office due to high memory & CPU Uses of UC520, sometime 100% CPU Used of UC520 and we have lossed internet access from Router from last two day's, all was going well before two day's, we haven’t had this happen before Last Thursday, but when I reboot router it's working again
coinop-uc520#sh proc cpu his
coinop-uc520 02:38:41 PM Saturday Apr 9 2011 WST
111112222211111
[Code]....
View 1 Replies
View Related
Jul 25, 2012
Have an issue where have two locations trying to get connected. first location has a cisco 861 and a uc500 for the phone system. The second location is using a UC520 for the phones and as the router. Below are the configurations of the 861 and the UC520.
Cisco 861
Current configuration : 7635 bytes
!
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
View 2 Replies
View Related
Jan 6, 2011
I am constantly getting error on UC520W Wifi from last Night, I am not getting with this error. What is the cause of this error, or is there any issue on UC520. [Code] .........
View 12 Replies
View Related
Jul 11, 2011
I am trying to setup time service on two devices. Once is a UC520, the second an 1840 router. I would like to use the FQDN of the time server which is north-america.pool.ntp.org. This is the recommended procedure as per ntp.org due to changes of IP addresses of time servers.
On the UC520 this is not a problem. I type in "ntp server north-america.pool.ntp.org" and this is how the command stays in the config. On the 1800 the FQDN is resolved and inserted into the config as an IP address. This works for now but kinda defeats the purpose of using a FQDN.
How can I keep the 1800 from converting to IP?
View 2 Replies
View Related
May 17, 2012
I've configured in an UC520 a SSL VPN.I can access properly and I can see the labels, but I only can access urls which are http, not https:I can access the default ip of the uc520 (192.168.1.10) but When I try to get access to a secure url I get the msg: Failed to validate server certificate I'm trying to access a Cisco Digital Media Manager, whose url is URL Does the certificate of both hardware has to be the same?
View 7 Replies
View Related
Mar 24, 2013
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies
View Related
Mar 4, 2012
I've one Cisco 3750G-12S with ip routing enable, the swtich is with IP Service firmware, with PRR support.Currently set my default static route 0.0.0.0 0.0.0.0 10.1.18.71 to my Firewall A Currently all of the VLAN for will be routed to 10.1.18.71
I've created a new VLAN 2 for my 10.1.2.0/24 network with the VLAN interface 2 ip address 10.1.2.10, my intention is to route 10.1.2.0/24 traffic to my 10.1.2.1 by creating the access list and route-map.
I've configure my test pc with a static ip and my gateway pointing to 10.1.2.10 (VLAN 2 gateway) , i'm not able to route to 10.1.2.1.
View 7 Replies
View Related
Feb 28, 2013
if the Cisco Switches in my enviorment can support WCCP?
View 1 Replies
View Related
Feb 2, 2011
Just bought this switch it has the IP base IOS and I need to use BGP and VRF-lite. My question is can I configure and use these two things without having to upgrade to the IP Services IOS?
View 5 Replies
View Related
Jan 18, 2013
Why does mine show this and NOT all 4 ports and 1 wan port?
Manases#sh verCisco Internetwork Operating System SoftwareIOS (tm) C831 Software (C831-K9O3SY6-M), Version 12.3(2)XA7 [code]...
How do I make it show all my ports? when I plug in something to port 1-4 it shows me on the log that I plug in to e0. I got port1-4 and 1 wan port.
View 8 Replies
View Related
Mar 8, 2012
I was recently given a PIX 501 router. I am very new to the world of Cisco, but want to learn. I got a few things setup on the router but, am not sure how to get it to use my DSL connection. My DSL modem IP is 192.168.2.1. Below is my router config. What more do I need to do? Also, is the outside IP not the IP of the DSL modem?
PIX Version 6.3(1)
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
[Code]...
View 1 Replies
View Related
Oct 16, 2012
I am finding the power consumption of WS-C3750X-24T-L, WS-C3750X-48T-L, WS-C3560X-48T-L and WS-C3560X-24T-L switches?
View 5 Replies
View Related
Dec 5, 2012
I got new task moving WS-3560X24 port layer 3 core switch from one branch to be moved to my branch and connect WS3560 layer 3 core switch my site network. Both core switch has got 3-4 cisco 2960 switch underneath and lots of vlan offcourse. I am thinking about creating etherchannel between these two switch.
View 2 Replies
View Related
Mar 17, 2012
i have the asa5505. the configuration of asa 5505 is:
: Saved
Code...
i analyzed this traffic i see problem with the nat- Asymmetric NAT rules matched for forward and reverse flows. where i made error?
View 0 Replies
View Related
Mar 15, 2012
how to backup the configuration of ACS 5.3 then restore it on the secondary ACS 5.3 Appliance in order to save time without configure the 2nd Appliance?
View 1 Replies
View Related
Mar 19, 2012
i have linksys modem which already running for differents vlans i cerated another different vlans 10 amd 20 for 10 and 20 i need internet how should i configure internet on another core switch3750
View 0 Replies
View Related
Feb 13, 2013
I have been using a Cisco 877 to connect to BT broadband and it was working fantastically with no issues. For reasons outwith my control we have moved to 02 and I cannot get the cisco router to connect (the supplied router works fine). O2 support is limited as they say they will not assist in the config of third party routers but they have supplied the below (the line has a static IP). I have also included my current config which was working fine with BT. I have attempted to write in the updated info but have been unable to get the line to connect. [code]
View 6 Replies
View Related
Jan 12, 2013
i have a router 2921 with the aproprieted voice card for E1 and licenses. I would like to know how to configure it for incoming and outgoing calls. I already configured the ephone and SIP phones for internal calls. now i just need to configure it for send and receive external calls.
Router:
IOS: c2900-universalk9-mz.SPA.153-1.T
CME: 9.1
ISP from Brazil:
type: E1
signal: R2 Digital
Channels: 32
Phone Number Iniital: XXXX-9250 (main)
ephones-dn numbers: 9250 to 9280
View 5 Replies
View Related
Nov 28, 2012
I have a network behind an 861 and users are unable to access e-mail from the local exchange server from their iPads using the 802.11wireless network. The wilrelss network is working fine and the iPad users connect fine.I was told that that i need to configure "hairpin DNS".
View 2 Replies
View Related
May 2, 2012
Any configuration example to build a vpc b/w 5ks and 7ks? i have total 4 links between them . If not, I am assuming to have the following config for the port-channels:- (Provided the vpc domain is configured).
N5k1 and 2:
int eth1/10-11
channel-group 10 mode active
switchport mode trunk
int po10
switchport mode trunk
switchport trunk allowed vlan a-d
[code]....
So, its basically vpc 10 that has 4 physical links b/w the vpc domain of 7ks and vpc domain of 5ks.
View 3 Replies
View Related
