We've recently started using some 2911's on our network running IOS 15.0(1r)M9. I noticed, much to my frustration that the OIDs with the MIB RFC1213: ip RouteTable1.3.6.1.2.1.4.21 are not supported.
Any alternative MIB for viewing routing table information via SNMP on any of these devices running a similar IOS?
Is SSH v2 feature is supported on cisco 3560G switch for below image if no what is the latest image .
c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin)
I see several code versions that seem to support on ACE30.Is A2.3.4 Or A2(3.5) that latest version for ACE20-MOD-9?Will the version 4 or 5 run on ACE20?I currently user A2(3).
View 3 Replies View RelatedThe table referenced in the new 1.1 ISE guide show 12.2(33)SXI6 is the minimum version for support. Does this mean this version or above? Does ISE is tested in newer SXJ streams? We have a massive rollout of SUP720s to do and need to know the most stable version to load in preparation for ISE.
View 1 Replies View RelatedWe have a cisco 2911 cisco router so i want to use as a load balancer using two different ISP networks, example if the first ISP network gets down i need the second ISP will take over all routing and get for internet access
here is my scenerio..
First ISP = PUblic ip = 155.1555.155.2 gateway = 155.155.155.1
seceond ISP Public = 40.51.16.9 gateway = 40.51.16.1
Inside network = 192.168.1.0. /24
i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies View Relatedif on the ASA 5512-X virtual contexts are supported with version 9.1 ?
I found different information on the Cisco web, the ASA datasheet says it is supported but in the configuration guide I found exactly the opposite information.
Cisco ASA Series General Operations CLI Configuration Guide 9.1 and 8.6 [URL]
Cisco ASA 5500 and ASA 5500-X Series Next- Generation Firewalls for Small Offices and Branch Locations Data Sheet (Updated) [URL]
I need to know for shure if the aps listed below are compatible with 5508 controller version 7.1.91.0
the ap's are
AIR-LAP1242AG-E-K9
AIR-LAP1242G-E-K9
AIR-CAP3501E-E-K9
AIR-CAP3502E-E-K9
AIR-LAP1231G-E-K9
of course I checked release notes [URL]
I thing that i find some bug in the newest IOS 15.1.4M.
The case is falow:
I start to configure failover for the costomer - make default route, make the default path but i cant find the comand IP SLA monitor. Is some meet this problem with this IOS or just Cisco make some chenge in the CLI commands?
Tomorrow i will try with IOS version 15.1.1T.
The Cisco 2911's have aggregate 1.6 Gbps towards route processor - I am trying the same specs for Cisco 3845 router? from url...The EHWIC slot provides enhancements to the prior generation's high-speed WAN interface card (HWIC) slots while provide maximum investment protection by natively supporting HWICs, WAN interface cards (WICs), voice interface cards (VICs), and voice/WAN interface cards (VWICs).
• Four integrated EHWIC slots on the Cisco 2901, 2911, 2921, and 2951 allow for more flexible configurations.
• Each HWIC slot offers high-data-throughput capability
• Up to 1.6 Gbps aggregate toward the route processor
• Up to 2 Gbps aggregate to other module slots over the MGF
We have 2 x C6506E and 2 x C3560-48's, they are all interconnected via port channels at 2Gb per channel. The 6506's are running CEF but the 3560's are not (The 3560's carry all our server traffic).When I do a show CEF on the 3560's it says %IPv4 CEF not running. There does not appear to be a global command to enable CEF on these switches.Is this an IOS version option or is not supported on the hardware platform?
View 3 Replies View RelatedAny example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies View RelatedI couldn't access internet with route specified i know the problem with the route or nat.i have 2911 router [code]
i could ping from lan Ip's to ISP1 and ISP2 gateway IPS. but when i ping to any site llike example gmail.com packet s not moving out to the ISP1 or ISP2 interfaces. [code]
I am having this problem trying to connect to my university network trough the vpn client from a pc running Windows 7 Ultimate 64-bit: the client connects but I have no Internet access. I first believed that the problem was related to the fact that I had ZoneAlarm Free Antivirus+Firewall installed, but I made several steps, including the complete removal of the ZoneAlarm product, and I still have the same problem.
Here's what I see in the log:
Cisco Systems VPN Client Version 5.0.07.0290
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
[code]....
Using the same client (32 bit version) in another pc of my lan which runs Windows XP and that had never ZoneAlarm installed on it, I have no problems.Also, using Shrew Soft Vpn Client 2.1.7 on the problematic pc I can connect to vpn without problems, so I am really stuck trying to understand what's wrong with Cisco Vpn Client.
Is there a known bug for Nexus 7K version 6.0(4) related to route redistribution?I have few vlan interfaces and being redistributed to the BGP.vlan interfaces are all up ang pingable.After configuring redistribution, vlan route is not in the bgp table.sho ip bgp is saying "path invalid"
BGP routing table entry for 10.165.101.192/28, version 26302
Paths: (3 available, best #3)
Flags: (0x180c0021) on new-list, is not in urib, need resync with RIB, exported, has label
vpn: version 47719, (0x100002) on xmit-list
local label: 492294
[code]....
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View RelatedMcAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedI've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
I am having one router CISCO2911/K9 (Cisco 2911 w/3 GE,4 EHWIC,2 DSP,1 SM,256MB CF,512MB DRAM,IPB). But now my management asking me to upgrade this router as CISCO2911-SEC/K9.
What will be the BOM for this up gradation.
Can we use ACS 4.1 version recovery disc on 4.2 verison to recover the forgotten password.
View 1 Replies View Relatedwhich version of prime infrastructure supports wlc5508 version 7.4
View 2 Replies View Relatedprovide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View Relatedi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View RelatedWe are looking to upgrade our WiSMs to version 7.0.230.0, but the Cisco compatibility matrix suggests we need to upgrade WCS to the same version (it is currently on 7.0.172.0). My question is can we upgrade the WiSMs and do the WCS at a later date with no issues or do we need to do them at the same time to keep visibility of everything?
The reason I ask is that some of my clients use lobby ambassador for some of their users and they will need wireless access on the day we are due to upgrade WCS (the WiSMs are due to be upgraded and rebooted earlier that morning.
If the "GLC-SX-MM" is offical supported on "SPA-5X1GE-V2" ?My customer tested it and it seems to work but now i need an offical statement In the data sheet there is no entry of the requested SFP. url...
View 3 Replies View RelatedI have a Cisco 7206VXR with NPE-400. The IOS version is 12.4(24)T3. I installed a SA-VAM in the router in slot 6 but getting the following on the console.
AP-Pune-RT#Feb 23 11:16:34.484: %PA-3-NOTSUPPORTED: PA in slot6 (Unknown (type 650)) is not supported on this chassisFeb 23 11:16:34.484: %PA-3-DEACTIVATED: port adapter in bay [6] powered off.Feb 23 11:16:34.584: %PA-2-PABRIDGE: Failed to config bridge for PA 6Feb 23 11:16:35.384: %PA-4-IMPROPER_REMOVAL: Improper removal for slot 6.Feb 23 11:16:35.384: %PA-3-DEACTIVATED: port adapter in bay [6] powered off.Feb 23 11:16:35.468: %CRYPTO-4-PKT_REPLAY_ERR: decrypt: replay check failed connection id=975, sequence number=677864
Is the SA-VAM not supported in the Router 7206VXR?
I have an issue with Cisco 3560V2-24-PS which it indicates not supported in DFM. I can see the device working properly when I do snmpwalk and snmv3 test and device credential test. In fact I can see chassis view of this device.
IP Address = 10.10.1.60
DNS Name = DISTRI_SW02
Device Status = Unknown
Device Type = N/A
Aliases = N/A
Containments = N/A
But in LMS 3.2 supported device it indicates as supported. Current version of the switch is 12.2(58)SE2 which is higher than the minimum requirement 12.2(50)SE1. I tried to downgrade/upgrade IOS and still no luck.
As per information in the creent DFM (see below), it is supposedly supported 59.1.3.6.1.4.1.9.1.1023Cisco Catalyst 3750V2-24PS SwitchDFMDeviceUpdates19.0 Below is the current version of the LMS modules;
Products Installed Showing 1-9 of 9 records Product Name Version With Patch Level Installed Date 1.Campus Manager5.2.110 Oct 2012, 13:11:57 GMT+08:002.CiscoView6.1.910 Oct 2012, 11:27:52 GMT+08:003.CiscoWorks Assistant1.2.010 Oct 2012, 11:27:52 GMT+08:004.CiscoWorks Common Services3.3.010 Oct 2012, 11:27:52 GMT+08:005.Device Fault Manager3.2.010 Oct 2012, 11:27:52 GMT+08:006.Integration Utility1.9.010 Oct 2012, 11:27:53 GMT+08:007.Internetwork Performance Monitor4.2.010 Oct 2012, 11:27:53 GMT+08:008.LMS Portal1.2.010 Oct 2012, 11:27:53 GMT+08:009.Resource Manager Essentials4.3.110 Oct 2012, 13:17:50 GMT+08:00
Also my current device update.Showing 1-9 of 9 records Product Name Device Type Count 1.Campus Manager02.CiscoWorks Common Services03.CiscoView7614.CiscoWorks Assistant05.Device Fault Manager9366.Internetwork Performance Monitor07.LMS Portal08.Integration Utility09.Resource Manager Essentials812 I already downloaded all the patches online and all device updates were also updated.
There is support of devices not manufactured by cisco?For example satellite modems.
View 1 Replies View RelatedWhich is the most stable, less processor intensive and VPN supported IOS for 2611xm. Currently I am using 12.4(15)T7 C2600-ADVENTERPRISEK9-M. But this image is causing lot crashes. My router uptime never crossed 4 hrs. It is crashing very frequently. Any issue with this image in 2611."
View 2 Replies View RelatedAfter upgrading to 7.2 on my 5508 WCS, the 1310 APs will no longer join. After a call to TAC they said the 1300 and 1400 APs are no longer supported on WCS. Is there any plan to add them back as supported in future releases?I was thinking I could downgrade my backup 5508 and change the APs to autonomous. Or is there some easier way to make them autonomous?
Also, as a low cost outdoor AP, I guess I am reduced to putting 1262s in a NEMA box with outdoor antennas. The 1552s are way too expensive for the quantity I need. Is there some other inexpensive outdoor AP that will replace 1300-1400 series?
Recently I purchased AIR-WLC2112-K9, but when I logged in I saw that system shows only 6 APs supported (I made print screen in addition). I'm running IOS v. 7.0.116.0 and I saw that there was some problems with earlier versions of IOS, but not this one.
View 5 Replies View Relatedwe just purchased 2 asa 5585-40's and tried to add them to our lms 3.2 system and we were informed by cisco tac that they were not supported in lms 3.2. since we don't having funding for an upgrade, any work around within lms that could allow me to add the devices so i can use lms for syslog and to fetch the firewall configs on a regular basis, instead of having to setup a seperate syslog server and having to tftp the config's everytime i make a change.
View 3 Replies View RelatedService policy output command is not supporting on Vlan interface of Cisco 2900 Router.I am having one HWic 4ESW Card and configured VLAN interface. But Service policy output command is not supporting.Same config is supporting in the Cisco 2800 Router.
View 13 Replies View Related