Cisco :: LMS 4.0 Supported Devices?
Jul 14, 2011There is support of devices not manufactured by cisco?For example satellite modems.
View 1 Replies
ADVERTISEMENT
Cisco Wireless :: Samsung SGH-1747M / Supported Android Devices On WLC
Feb 19, 2013looking for an info if Samsung SGH-1747M device running Android version 4.1.1 supported on Cisco WLC 7.4.100.0 Basically the Samsung device cannot join our test wifi (ipads and ihones are OK).
View 3 Replies View RelatedCisco Wireless :: 5500 WLC And 3600 WAPs / Reference Document For Devices Supported Under 5Ghz
May 5, 2013I am looking for a reference document for the type of devices that are supported under 5Ghz. We are using a 5500 WLC and 3600 WAPs. Lot of users cannot connect to network via mobile devices. Is there a reference doc from cisco which i can use to inform them?
View 5 Replies View RelatedCisco Switching/Routing :: List Of Supported External HDDs / NAS Devices For 857w Router?
Mar 19, 2012Where can I find a list of supported external HDDs or NAS devices for a Cisco 857w router?
View 2 Replies View RelatedTEGs80G - Swap Unmanaged Devices With More Expensive Cisco Devices?
Jun 1, 2012Currently my home network is being switched via TrendNet TEGs80G unmanaged gig switches. I have been using them for about a year now with no issues. As my home network becomes more advanced, I recently just added a Cisco ASA5505, I am thinking about swapping those unmanaged devices, 4 of them, to managed. I was looking at the Cisco SG300-10 for upstairs, and a 16 port variant for my main core. These devices do not support full Cisco IOS cli, but they are manageable with a rich feature set nonetheless. My question is, should I swap the unmanaged devices with the more expensive Cisco devices, or just keep what works and save the money until I really need to spend it. As previously stated, my home LAN works just fine as it is, however my WiFi, NTV550s, server and workstations are all on the same network. Probably not the most secure but it is what it is without VLAN support.
View 11 Replies View RelatedLinksys Wireless Router :: E4200 Can See None Of Devices Attached To Power-line Devices
Aug 15, 2011I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies View RelatedWireless Devices Can't Connect To Wired Devices?
Oct 11, 2012All of a sudden my laptop, android phone and blu ray player (all wireless devices) can't communicate with my wired devices (marantz receiver and samsung tv). Everything still connects to the internet independently but i can't for instance play music from my wireless laptop to my wired marantz receiver. I had no trouble with this last week and didn't change anything (that I'm aware of) I did get Verizon to switch out my router but it didn't solve anything. My wife's computer also cannot connect to wired devices. Lastly, if I connect my laptop with via ethernet cable it sees wired devices fine. I tried shutting off windows firewall but didn't work. I have no other firewall/virus software installed. I can ping to all devices (wired and wireless) from my laptop.
View 1 Replies View RelatedCisco WAN :: Is GLC-SX-MM Supported On SPA-5X1GE-V2
Apr 10, 2013If the "GLC-SX-MM" is offical supported on "SPA-5X1GE-V2" ?My customer tested it and it seems to work but now i need an offical statement In the data sheet there is no entry of the requested SFP. url...
View 3 Replies View RelatedCisco VPN :: SA-VAM Not Supported In 7206VXR?
Feb 22, 2011I have a Cisco 7206VXR with NPE-400. The IOS version is 12.4(24)T3. I installed a SA-VAM in the router in slot 6 but getting the following on the console.
AP-Pune-RT#Feb 23 11:16:34.484: %PA-3-NOTSUPPORTED: PA in slot6 (Unknown (type 650)) is not supported on this chassisFeb 23 11:16:34.484: %PA-3-DEACTIVATED: port adapter in bay [6] powered off.Feb 23 11:16:34.584: %PA-2-PABRIDGE: Failed to config bridge for PA 6Feb 23 11:16:35.384: %PA-4-IMPROPER_REMOVAL: Improper removal for slot 6.Feb 23 11:16:35.384: %PA-3-DEACTIVATED: port adapter in bay [6] powered off.Feb 23 11:16:35.468: %CRYPTO-4-PKT_REPLAY_ERR: decrypt: replay check failed connection id=975, sequence number=677864
Is the SA-VAM not supported in the Router 7206VXR?
Cisco :: LMS 3.2 / 3560V2-24-PS Not Supported In DFM
Oct 9, 2012I have an issue with Cisco 3560V2-24-PS which it indicates not supported in DFM. I can see the device working properly when I do snmpwalk and snmv3 test and device credential test. In fact I can see chassis view of this device.
IP Address = 10.10.1.60
DNS Name = DISTRI_SW02
Device Status = Unknown
Device Type = N/A
Aliases = N/A
Containments = N/A
But in LMS 3.2 supported device it indicates as supported. Current version of the switch is 12.2(58)SE2 which is higher than the minimum requirement 12.2(50)SE1. I tried to downgrade/upgrade IOS and still no luck.
As per information in the creent DFM (see below), it is supposedly supported 59.1.3.6.1.4.1.9.1.1023Cisco Catalyst 3750V2-24PS SwitchDFMDeviceUpdates19.0 Below is the current version of the LMS modules;
Products Installed Showing 1-9 of 9 records Product Name Version With Patch Level Installed Date 1.Campus Manager5.2.110 Oct 2012, 13:11:57 GMT+08:002.CiscoView6.1.910 Oct 2012, 11:27:52 GMT+08:003.CiscoWorks Assistant1.2.010 Oct 2012, 11:27:52 GMT+08:004.CiscoWorks Common Services3.3.010 Oct 2012, 11:27:52 GMT+08:005.Device Fault Manager3.2.010 Oct 2012, 11:27:52 GMT+08:006.Integration Utility1.9.010 Oct 2012, 11:27:53 GMT+08:007.Internetwork Performance Monitor4.2.010 Oct 2012, 11:27:53 GMT+08:008.LMS Portal1.2.010 Oct 2012, 11:27:53 GMT+08:009.Resource Manager Essentials4.3.110 Oct 2012, 13:17:50 GMT+08:00
Also my current device update.Showing 1-9 of 9 records Product Name Device Type Count 1.Campus Manager02.CiscoWorks Common Services03.CiscoView7614.CiscoWorks Assistant05.Device Fault Manager9366.Internetwork Performance Monitor07.LMS Portal08.Integration Utility09.Resource Manager Essentials812 I already downloaded all the patches online and all device updates were also updated.
Cisco VPN :: Supported IOS For 2611xm?
May 2, 2011Which is the most stable, less processor intensive and VPN supported IOS for 2611xm. Currently I am using 12.4(15)T7 C2600-ADVENTERPRISEK9-M. But this image is causing lot crashes. My router uptime never crossed 4 hrs. It is crashing very frequently. Any issue with this image in 2611."
View 2 Replies View RelatedCisco :: 1310 AP No Longer Supported On WCS 7.2
Jun 19, 2012After upgrading to 7.2 on my 5508 WCS, the 1310 APs will no longer join. After a call to TAC they said the 1300 and 1400 APs are no longer supported on WCS. Is there any plan to add them back as supported in future releases?I was thinking I could downgrade my backup 5508 and change the APs to autonomous. Or is there some easier way to make them autonomous?
Also, as a low cost outdoor AP, I guess I am reduced to putting 1262s in a NEMA box with outdoor antennas. The 1552s are way too expensive for the quantity I need. Is there some other inexpensive outdoor AP that will replace 1300-1400 series?
Cisco :: WLC2112 Shows Only 6 APs Supported
Oct 11, 2011Recently I purchased AIR-WLC2112-K9, but when I logged in I saw that system shows only 6 APs supported (I made print screen in addition). I'm running IOS v. 7.0.116.0 and I saw that there was some problems with earlier versions of IOS, but not this one.
View 5 Replies View RelatedCisco :: ASA5585-40 Not Supported In LMS 3.2 System
Nov 20, 2011we just purchased 2 asa 5585-40's and tried to add them to our lms 3.2 system and we were informed by cisco tac that they were not supported in lms 3.2. since we don't having funding for an upgrade, any work around within lms that could allow me to add the devices so i can use lms for syslog and to fetch the firewall configs on a regular basis, instead of having to setup a seperate syslog server and having to tftp the config's everytime i make a change.
View 3 Replies View RelatedCisco WAN :: QOS Not Supported On SVI Interface 2900
May 15, 2011Service policy output command is not supporting on Vlan interface of Cisco 2900 Router.I am having one HWic 4ESW Card and configured VLAN interface. But Service policy output command is not supporting.Same config is supporting in the Cisco 2800 Router.
View 13 Replies View RelatedCisco WAN :: ASR 1002 And HSRP Not Supported?
Dec 6, 2011I have a pair of physical ASR 1002 routers, called ASR-1 and ASR-2. I setup HSRP on both ASR-1 and ASR-2 on both g0/0/0 and g0/0/1 interfaces, nothing complicated, just straight forward HSRP.
Now Cisco TAC told me that HSRP is NOT supported between physical ASR routers. WTF!
Furthermore, they told me that HSRP only supported within a single ASR because of multiple routed processors. In other words, you can setup HSRP with a single physical ASR but not with two physical ASR routers.
HSRP can not supported with two physical ASR routers?
Cisco WAN :: Latest Supported IOS For 2811?
Aug 22, 2012latest supported version of IOS for the Cisco 2811?
View 3 Replies View RelatedCisco WAN :: NM-1CE1TI-PRI Module Is Not Supported On New ISR
Oct 11, 2011I have checked on Cisco.com and as per a module support document for ISR's G2, the NM-1CE1TI-PRI module is not supported on new ISR's.
Grateful if more clarification could be obtained about the above.
Will be router not detect the module when inserted in the chassis?
Cisco WAN :: ASR 1006 - IRB Feature Is Not Supported
Sep 9, 2011My problem with ASR 1006 as i tried to use the feature IRB ( integrated routing and bridging ) but i find that this feature is not supported i assume it may be a problem with IOS version or may be i made he configuration not in the proper way
so i am asking to try this feature on ASR 1000 series and work with it as I test this feature on other routers and it work just fine.
Cisco :: Supported VLAN On 2504 Wlc?
Dec 21, 2011Can a 2504 wlc use a vlan ids of 190X? I have found that it supports 512 vlans but I have not found any restrictions in the id used.Vlan id 190X is distributed by the isp (they have the ASAs in their central site) so if it is not supported I must prepare a vlan transfer between switches.
View 4 Replies View RelatedCisco WAN :: 6509 Says Not Supported Due To Hardware
Feb 6, 2011I have a 6509 and a 6506- same IOS version and flavor, same hardware, etc. One supports rate limiting on the VLAN interfaces, the 6509 says "not supported due to hardware". What is the difference here? Im very confused on this since I was under the impression the chassis were the same- just in size.
View 1 Replies View RelatedCisco Switching/Routing :: Is MLS QOS Supported On 877
Jan 17, 2013Is 'mls qos' supported on Cisco 877? I want to implement bandwidth limiting on a specific IP using access-lists on a class-map.If yes, what version and software do I need (ip base, adv security, etc)?
View 2 Replies View RelatedCisco :: Does Xeon E7540 Supported In LMS 4.1
Oct 19, 2011is the Xeon E7540 supported in LMS 4.1 ? in HW Requirements he is not explicit listed,[URL]
View 1 Replies View RelatedCisco :: 2T Modules Supported With LMS Prime 4.1 And 4.2
Apr 1, 2012I would like to know which 2T (like WS-X6848-TX-2T, WS-X6908-10g-2T,...) modules are supported with LMS Prime 4.1 and 4.2.
View 6 Replies View RelatedCisco :: Frame Relay On Sub-Interfaces Not Supported?
Mar 24, 2012working through a lab and can't seem to configure frame relay on subints. I assume it's not supported but this seems basic; am I doing something wrong?
View 4 Replies View RelatedCisco WAN :: EHWIC-3G-HSPA+7 Not Supported In Vrf Setups?
May 8, 2012we set up a 1941 with c1900-universalk9-mz.SPA.151-4.M3.binand tried to bring up EHWIC-3G-HSPA+7 in the vrf. [code]
View 4 Replies View RelatedCisco :: Sup720 - Supported Slots On A 6513?
Nov 28, 2011Can the sup720b be used in any other slot on a 6513 besides 7 and 8?
View 1 Replies View RelatedCisco Switching/Routing :: 3750x 12s Says That It Is Not Supported In CNA
Mar 28, 2012Why does my 3750x-12s switch say it's not supported in CNA??? I upgraded to CNA 5.7.1 and still says unsupported. This device is supported or I'm just missing something.I use CNA heavily to manage our MANY vlans.
View 1 Replies View RelatedCisco WAN :: Number Of Users Supported On ISRs G2 880
Apr 16, 2013This is a feature that I have researched for by looking at ISRs G2 data sheets and cisco.com website.The number of users that can be supported or the recommended number of users per router chassis/model is not mentioned anywhere.However this is mentioned in the Cisco 880 ISR data sheet. What are the number of users that can be supported or the recommended number of users on Cisco 1900/2900/3900 ISRs?
View 4 Replies View RelatedCisco :: AIR-PI21AG-A Card Supported On Windows 7?
Aug 23, 2011If it is, can you point me to the correct drivers page as I cannot find it.
View 1 Replies View RelatedCisco Switching/Routing :: SFP+ Supported On 6509-E?
Nov 16, 2011We are trying to migrate from 1g to 10G, couldn't find any module on 6509-E which supports 10G on SFP+ ...I can see X2 and Xenpacks .. but not SFP + .what exactly this Xenpack means ?
View 3 Replies View RelatedCisco :: WS-x4612-SFP-E Card Supported In CiscoView?
Sep 8, 2011I would like to know if WS-x4612-SFP-E card is support in ciscoview ? If not, when it will be support ?
View 4 Replies View RelatedCisco Switching/Routing :: Does OTV Supported On Cat 6500
May 6, 2013On googling I came across documents that say OTV (Overlay Transport Virtualization) is supported on Cat 6500. Any authentic information whether OTV is supported on Cat 6500, especially with Sup-720B? FYI, Cisco Feature Navigator does not mention it.
View 1 Replies View Related