I'm having problems installing LMS 4.2 in other partition. I have two operating system. One on C: Windows 7 Pro and One on D:Windows Server 2008,after installing it on Windows Server 2008, i'm able to access the server using the command net start crmdmgtd; but if i restart my machine it gets and error (blue screen) and says: Could not find ntdll.dll in the dynamic library. NTSerializeboot.
View 1 RepliesIs it possible to partition the hard disk after installing the Windows OS?
View 9 Replies View Relatedhow to do partition in internet connection?because when ever my brother uses net even if its only facebook i get lag i wanna know how to limit the net they can use
for example our net has 10kbps i get the 6 the other pple connecting to my net get only 4 i connect to the lan they connect thru wifi
I have in a workgroup a Windows 7 Ultimate X64 laptop and a Windows XP Pro SP3 desktop PC. If i try to share a partition from W7 i can see it over network in XP but i can't access the files or folders from it, the error being this one: "\ComputerNamePartitionName is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if yout have access permissions. Access is denied." In W7 i've set Everybody with full access (read and write); both computers have Windows Firewall and BitDefender Internet Security installed on them but doesn't seems to be important since i've tried to use the shared partition from W7 with Firewalls and BitDefenders On and Off and the problem was the same!
View 3 Replies View RelatedWired computers can't see wireless and wireless can't see wired pcs.
View 8 Replies View RelatedI have a Sony Viao PCG-71312L laptop that has Windows 7, 64-bit as OS. I loaded on Ubuntu as want to learn more about Linux. The wireless locator finds the signal but won't connect.It says "ethos" and then when you click from there I don't get through. Just seems to keep looking forever, then says after 3 minutes can't connect.It could be I need a specific driver for the Ethernos wireless device, I am not sure. Further I am had a hacking where I had to change wireless settings so I may have done it myself. I am able to connect on my Windows 7 wireless network account but not the Linux one. I tried deleting the account on the Linux Ubuntu that shows up but this didn't work.May have made worse.Is this on my wireless device side, meaning I need to change/get password ect or the Ubuntu side where it's some type of common problem. Do I need to access through the router web page? Incidentally that's blocked for me too.
View 2 Replies View RelatedTwo physical drives. Drive 0 has two partitions C and D. C is operating system (XP Pro) and D is data only. Drive 1 has one partition F and is used for internal backup. Drive F can be set to be shared. Partition D on Drive 0 will not accept sharing. It reverts back to the $D admin share after setting up a new share. The icon (hand) that indicates shared drive does not appear either. I assume there is a registry setting that has drive 1 blocked, but am unable to find it.
View 6 Replies View RelatedIn the current set up I have a LAN stack of 5 3750 switches configured as an access stack. As per the requirement I need to partition the current 5 switch stack into two individual stacks of 3 & 2 switches respectively. Kindly let me know the step by step process withh all the necessary commands, reloads and reconnections. I purpose to do it by changing the priority of current member switch to 15 so that its elected as Master in the new partitioned switch stack. But not sure what all steps required and in which order.
View 1 Replies View RelatedThe network gods recently updated our 6500 and upon reboot, the FWSM booted to CF:1 maintence partition,which caused an immediate outage. On the router, I ran the following command to set the default FWSM boot partition to the configuration with:Router#boot device module 4 cf:5 However, it appears the "show boot device" command has been replaced with "show bootvar" which doesn't show me which partition the router will boot the FWSM to. Is there a command I can run from the Router that will actually confirm the boot partition for the FWSM if the router reloads.
View 1 Replies View RelatedI've tried to attach my external HDD to X3000 router and share entire partition through my home network, but it didn't detect any HDD with NTFS partition and some FAT32 partitions as well. Does it support NTFS partition and detects them to share through network? If not, is there any plan to add this feature to support NTFS partitions? Personally, I think today all media files which are using to share in home networks are huge and big files, usually more than 2GB and require to be stored in NTFS drives.
View 3 Replies View RelatedI've lost about a TB worth of data. I'm rebuilding a computer and had my hard drive, a Western Digital Caviar Black WD1001FALS 1TB, in an external enclosure so that I could access files from it until I could move them to a new drive. I just happened to hook the drive up to the USB port on my new Linksys EA3500 router and now I can't see anything. I believe the process of plugging the drive in, allowed the router to mess with the partition table of my drive. Before, when things worked I saw three logical drives. one of about 50-75 MB of reserved space. One of about 80 GB that was my original system drive and one of about 920 GB that was my main data drive. All of these were NTFS. Now when I look at the drive, all I see is one drive FAT32 drive of about 71 MB.If I look at the drive under Computer Management, Storage, Disk Management, I see the drive is made up of a 71 MB FAT 32 Primary Partition and a 932 GB Unallocated partition.Am I totally screwed? Is my data still there and is there any way for me to access it or any utilities I can use to get to my data in this unallocated partition? What the heck did this thing do to my drive without permission?
View 5 Replies View Relatedpartition the departmental IP network address block to create a staff and a student subnet. Each of these will be identified by its own network address and netmask. It is university policy that you must be economical with the IP addresses. That is, the subnets must be as small as possible, but they must be large enough to accommodate the maximum number of hosts you were given. Also, it is university policy that the respective gateway router to the outside world should always be given the highest possible host IP address in the subnet. The student subnet should have a higher IP network address than the staff subnet. The network must be able to support up to 60 machines on the staff subnet (not counting the router) and up to 120 machines on the student subnet (also not counting the router).
IP address/netmask
University network address127.158.128.0
University network mask255.255.192.0
University internet gateway IP address127.158.191.254
Department network mask255.255.254.0
Department router address127.158.129.254
Suppose that the network address of the departmental network is 127.158.128.0 (calculated by AND between Dep network mask and Dep router address)I know that 60 machines would use 6 bits for the staff subnet.the netmask of staff would be 255.255.255.192.how can I figure out the the IP network address of the staff subnet.I have worked out the range for the staff subnetwork.
127.158.128.0 - 127.158.128.63
127.158.128.1 = Gateway address
127.158.128.63 = Broadcast address
Now how can I calculate the IP network address of the staff subnet?
Trying to upgrade a pair of ACS servers from 5.2.0.26 base to patch 4. I have tried creating different repositiories that are SFTP, FTP, and Local. The secondary unit(ROTACS2) upgraded fine with no problems the primary(ROTACS) will not, see below.
Cisco Application Deployment Engine OS Release: 1.2ADE-OS Build Version: 1.2.0.182ADE-OS System Architecture: i386
Copyright (c) 2005-2009 by Cisco Systems, Inc.All rights reserved.Hostname: ROTACS
Version information of installed applications---------------------------------------------
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.2.0.26Internal Build ID : B.3075
ROTACS/mpartain#
[code]....
It appears that the GPG key is not vaild on this primary server. The patches are in the repositories and I used the acsrepo repo to install on the ROTACS2 secondary server.I have looked through articles and the only mention is to not use TFTP, which I am not. I have also tried to apply patches 1-3 with the same results.
I built a new Win2k8 server meeting all prereq's. This is a new install of LMS. Right at the beginning of the install process, i get this error and the install halts.
View 2 Replies View RelatedI want to install a windows operating system in my machine but my machine dont have a CD-ROM. so i want to install an OS from using my another PC(Laptop)'s CD-ROM. So is it possible to install OS into my one machine from another different machine(windows-7) via sharing the drive .
View 4 Replies View RelatedI am installing Cisco blank CF upgrades (double the capacity of the CF that came with the router) in Cisco 3845 routers and I cannot get the IOS to load.
Network security requires tftp be disabled, so I am limited to xmodem. Slow, but it works. I know the IOS download is good, because I can load it on the CF that came with the router.
I can install, format and read the new flash. But the download locks up and bombs about 1/3 of the way through.
Note: CF that came with the router was "C" so I used the format flash: command. The new flash reads the same as the old, except that there is no file IOS loaded.
I've never had an issue upgrading an IOS, but this is my first shot at installing on a new CF.
im trying to install Cisco prime LMS 4.2.3 for Windows 2008 R2 standard x64.however i have received this error message.
----- end of Dependency Handler Log File
-----Dependency Handler Errors
ERROR: csjre not found
ERROR: Component csjre is not found.
cdone : depends on :csjre
----- end of Dependency Handler Errors
[code]....
Our customer is having problems with installing Anyconnect with CSD on MAC. Here is log file:
libcsd.log:
[Mon Jan 28 11:09:13.433 2013][libcsd][debug][hs_download_file_to_buffer] attempting to download file: /CACHE/sdesktop/hostscan/darwin_i386/manifest
[Mon Jan 28 11:09:13.433 2013][libcsd][debug][hs_transport_setpeer] setting peer
[Mon Jan 28 11:09:13.433 2013][libcsd][debug][hs_transport_setpeer] setting l2 peer: (https://yyy.xxx.si)
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_setpeer] setting peer done. peer = https://yyy.xxx.si, referrer = https://yyy.xxx.si
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_setredircount] setting redirects
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_setredircount] setting redirects: (10)
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_setredircount] setting redirects done
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_get] sending get request
[Mon Jan 28 11:09:13.473 2013][libcsd][debug][hs_transport_curl_get] libcurl error: Error
It looks like there should be an redirection for downloading file and it cannot be done.
ASA version:
IOS: 8.4(2)
CSD: 3.6.6228
Anyconnect: 3.1.02026
MAC:
MAC OSX: 10.8.2 with latest updates
Kernel: Darwin 12.2.0
Kernel boot: x86_64
AnyConnect on MAC:
Anyconnect client: 3.1.02026
Components: VPN, DART and Posture
I was trying to install a SPA-IPSEC-2G on 7606-S chassis. I installed the SPI/SPA cards in slot 3, after that I checked with "sh module" and we could see the module "OK". After this we tried to configure a VPN tunnel but we received messages in the other router about "no ipsec package".
I was checking and I tried "sh crypto engine accelerator statistic" and we got the message: " There is no crypto device".
I don't know about installation commands in references and I don't know about restrictions or configuration modes.
I am wondering if i can install the LMS in two servers using one license not two?
Also i want to know if i can manage the same set of devices in both servers if they are using the same license or this will not work?
Should i select specific ranges of IP's for both server and in this case, i can use two servers with the same license?
I have a question relating to installing lines underground in a conduit.
We've had several lines get hit by lighting which leads to the line being bad, equipment being damaged and so on. We've then installed a new cat6e cable WITH lightning arrestors which were blown almost instantly on the first storm. This is obviously a bad ground issue, and a risk to the equipment.
This being said, I would like very much to run fiber optic cable in this conduit and then convert it to ethernet, but I don't know if fiber is susceptible to lighting like ethernet cable is, OR if there are other methods to prevent this freak of nature crap!
Is it possible to install the above alfa card on mac os x 10.7.4?
View 2 Replies View RelatedI would like to learn how to install an OS like XP or linux over the network.
View 2 Replies View RelatedI am looking for the appropriate procedure for connecting an external HDD to a D-Link router with a USB 2.0 port. I am told I need to create a TCP/UDP 19540 port on my system.
View 1 Replies View RelatedI have had my new computer up and running for 2 days amd have installed 2 games but i couldnt connect to the internet because my driver installation cd says "D: is not a valid win32 application" when i try to run it and i dont know what to do i have tried resetting cd to defaults, installing manually by going in to cd files and have tried running in safe mode but nothing works .i have windows 7 home premium 64 bit OS
View 3 Replies View RelatedI'm installing WIFI for my personal business, and want to make sure my server and modem are unaccessable by WIFI users. I have the modem set to 192.168.1.1 and router(wifi) to 10.0.0.1. The problem is i can still type in 192.168.1.10 (server's ip address) or 192.168.1.1 while on WIFI and i get can still get to both.
View 2 Replies View Relatedall the drivers required to connect to the Internet wireless,,
View 1 Replies View RelatedWe have cisco 1941 as router in office, it's dhcp server, it has only vlan 1 192.168.4.0/24?I've set up 1142 ap for wireless clients How can i make it give clients ips from dhcp server from vlan 1 ?
View 11 Replies View RelatedI am trying to configure SDM 2.5 on a cisco 2600.I have access via telnet to the router and was able to change the enable password - which i think is level 15 (right?) and setup (and bring up) the ip on the ethernet interface. I can ping - and get response from - the router Trying to install SDM on the router i need to provide the default username i tried both admin/administrator but SDM can't communicate with the router?
View 21 Replies View RelatedI have a new deployment I am working on. I am unclear on the Inline setup. One location is configured as a trunk between the router and the switch, with voice and data traffic going through it. We will be installing a 294 inline at this site.What impact will it have on voice traffic? We are using G0/0 for management, not the Inline interfaces. Is that any additional configuraiton needed to inline if done this way? I didn't get prompted for vlan ID, or anything like that during the setup as an accelerator.Are these setup with default optimizations out of the box, or is there additional programming needed once they are online? I found where to build custom applications, but wonder if there is anything needed to be done once they are online for default traffic.
View 1 Replies View Relatedwe have installed an evaluation version of Cisco Works LMS 4.0.1. Now we have purchased a license, but the evaluation period is over and I can't start the application anymore. Is there any possibility to install the license file after the evaluation period?
View 2 Replies View RelatedI've got an MSE 3310 that came with four-post rails for rack mounting. These came without instructions and we are having a hard time figuring out exactly how they work. They say General Devices C-300-S-124-RC-MOD
View 4 Replies View Relatedim trying to install a ios 12.2v on my switch. when the screen prompt it does not show me the user move symbol " SW1> ". all i see is " SW:" and from there i can not enter the commands to download from tftp server !
View 7 Replies View Related