I am wondering if i can install the LMS in two servers using one license not two?
Also i want to know if i can manage the same set of devices in both servers if they are using the same license or this will not work?
Should i select specific ranges of IP's for both server and in this case, i can use two servers with the same license?
we have installed an evaluation version of Cisco Works LMS 4.0.1. Now we have purchased a license, but the evaluation period is over and I can't start the application anymore. Is there any possibility to install the license file after the evaluation period?
View 2 Replies View RelatedI am planning on installing Clean Air Wireless network, using WLC 5508, WCS(with plus license) and MSE.
Which MSE license i need to get this to work ?
I'm trying to install performance license on ACE 4710 appliance and it was failed. [code]
View 11 Replies View Related i installed Data license(Evalutation) initally it took the license after reload, when i enter sh lic command the out put shows that Data license is installed and valid for...
But when i run sh ver command it only shws ipbase license and not the data license
I recieved my IPS module license for my ASA 5525 . I enetered the key via the ADSM and it prompted me to restart the firewall .. After that i cannot get into the firewall via the ASDM .
View 3 Replies View Relatedwe recently purchased L3 daughter cards (N55-D160L3-V2) for our 5548UPs along with the LAN Enterprise Services licenses (N55-LAN1K9).
I installed the cards and Ent Svcs lic this past weekend and everything went well excep that I couldn't enable the EIGRP feature .. apparently EIGRP requires the LAN Base (N55-BAS1K9-BUN) license even when you have the Enterprise lic installed, so I was able to dig up that license eventually (which comes with the L3 daughter card, incidentally). Another side effect of not installing the Lan Base lic is that the L3 card/module will be in an "offline" state until the Lan Base lic is installed. Either way, everything was working normally in L2 mode at this time.
So, here I was thinking I was ready to proceed with enabling L3 - this morning I installed the LAN Base license on one of the 5548s which apparently triggered the L3 Daughter card module to go active and triggered a switch reboot. Ok, not that big of a deal, knew that was probably coming. I expected the switch to come back up normally .. NOPE. The switch went into a continual reboot cycle where the console prompt would appear, then about 30 seconds later, would reboot again.
I finally ended up re-installing the original L2 card and the switch came right up. I see that LAN Base and LAN Enterprise are both still installed as well.
What have I done wrong here? Why did the switch go into a continuous reboot cycle once I installed the LAN Base license?
Here are more details :
Software
BIOS: version 3.5.0
loader: version N/A
[Code]....
What's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedI’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
We are planning to split the Private servers from the DMZ Servers and configure an additional Interface and segment for this purpose.
Private Servers Segment: 192.168.4.0/24 (there is no DHCP all servers' IPs are statically configured)
DMZ Segment: 192.168.3.0/24 (This is a future deployment)
LAN Segment: 172.17.0.0/16
Both, Private Servers and DMZ Servers are in a collocation as well as the ASA5520. There are multiple Branch offices that uses subnets within the 172.17.0.0/16 Network and they are connected to the ASA5520 via Metro-E.
I do not know if this is possible but what I want to do is this:
In order to avoid the change of internal DNS records I want to mask the DMZ servers with a Private Server IP when a Private server or LAN host wants to access it like this:
The FTP server in the DMZ has the IP address: 192.168.3.100. But when a PC from the LAN wants to reach the FTP server it should points to its old IP: 192.168.4.100. This way the PC sends a packet to the ftp.corporate.net (192.168.4.100) the ASA recieves the packet and translate it to the (192.168.3.100) and send it out through the DMZ Interface.
Also if the Private Servers wants to reach the same FTP the ASA will act like a proxy-ARP and send the paquet to the DMZ by means of the translation of the IP.
I Have exented vlan 120,121 from DC-1 to DC-2,the DC-1 and DC-2 are connected using L2 Trunk over fiber terminated on Cisco 6513 on both site ,the distance around 40 Km ,on the DC-2 i just assigned server-1 TO VLAN 120 while server-2 in vlan 121 ,but these servers unable to communicate neither with DC-1 Servers or betwen them locally on DC-2 ,pls note that the servers at dc-2 rely on DC-1 for routing.
View 7 Replies View Relatedi'm trying to connect 5 servers together to create a private network.Each server has a network of it's own and i'm trying to make all 5 servers communicate with each other to share and search data simultaneously..
View 16 Replies View RelatedTrying to upgrade a pair of ACS servers from 5.2.0.26 base to patch 4. I have tried creating different repositiories that are SFTP, FTP, and Local. The secondary unit(ROTACS2) upgraded fine with no problems the primary(ROTACS) will not, see below.
Cisco Application Deployment Engine OS Release: 1.2ADE-OS Build Version: 1.2.0.182ADE-OS System Architecture: i386
Copyright (c) 2005-2009 by Cisco Systems, Inc.All rights reserved.Hostname: ROTACS
Version information of installed applications---------------------------------------------
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.2.0.26Internal Build ID : B.3075
ROTACS/mpartain#
[code]....
It appears that the GPG key is not vaild on this primary server. The patches are in the repositories and I used the acsrepo repo to install on the ROTACS2 secondary server.I have looked through articles and the only mention is to not use TFTP, which I am not. I have also tried to apply patches 1-3 with the same results.
I'm having problems installing LMS 4.2 in other partition. I have two operating system. One on C: Windows 7 Pro and One on D:Windows Server 2008,after installing it on Windows Server 2008, i'm able to access the server using the command net start crmdmgtd; but if i restart my machine it gets and error (blue screen) and says: Could not find ntdll.dll in the dynamic library. NTSerializeboot.
View 1 Replies View RelatedI built a new Win2k8 server meeting all prereq's. This is a new install of LMS. Right at the beginning of the install process, i get this error and the install halts.
View 2 Replies View RelatedI want to install a windows operating system in my machine but my machine dont have a CD-ROM. so i want to install an OS from using my another PC(Laptop)'s CD-ROM. So is it possible to install OS into my one machine from another different machine(windows-7) via sharing the drive .
View 4 Replies View RelatedI am installing Cisco blank CF upgrades (double the capacity of the CF that came with the router) in Cisco 3845 routers and I cannot get the IOS to load.
Network security requires tftp be disabled, so I am limited to xmodem. Slow, but it works. I know the IOS download is good, because I can load it on the CF that came with the router.
I can install, format and read the new flash. But the download locks up and bombs about 1/3 of the way through.
Note: CF that came with the router was "C" so I used the format flash: command. The new flash reads the same as the old, except that there is no file IOS loaded.
I've never had an issue upgrading an IOS, but this is my first shot at installing on a new CF.
im trying to install Cisco prime LMS 4.2.3 for Windows 2008 R2 standard x64.however i have received this error message.
----- end of Dependency Handler Log File
-----Dependency Handler Errors
ERROR: csjre not found
ERROR: Component csjre is not found.
cdone : depends on :csjre
----- end of Dependency Handler Errors
[code]....
Our customer is having problems with installing Anyconnect with CSD on MAC. Here is log file:
libcsd.log:
[Mon Jan 28 11:09:13.433 2013][libcsd][debug][hs_download_file_to_buffer] attempting to download file: /CACHE/sdesktop/hostscan/darwin_i386/manifest
[Mon Jan 28 11:09:13.433 2013][libcsd][debug][hs_transport_setpeer] setting peer
[Mon Jan 28 11:09:13.433 2013][libcsd][debug][hs_transport_setpeer] setting l2 peer: (https://yyy.xxx.si)
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_setpeer] setting peer done. peer = https://yyy.xxx.si, referrer = https://yyy.xxx.si
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_setredircount] setting redirects
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_setredircount] setting redirects: (10)
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_setredircount] setting redirects done
[Mon Jan 28 11:09:13.434 2013][libcsd][debug][hs_transport_get] sending get request
[Mon Jan 28 11:09:13.473 2013][libcsd][debug][hs_transport_curl_get] libcurl error: Error
It looks like there should be an redirection for downloading file and it cannot be done.
ASA version:
IOS: 8.4(2)
CSD: 3.6.6228
Anyconnect: 3.1.02026
MAC:
MAC OSX: 10.8.2 with latest updates
Kernel: Darwin 12.2.0
Kernel boot: x86_64
AnyConnect on MAC:
Anyconnect client: 3.1.02026
Components: VPN, DART and Posture
I was trying to install a SPA-IPSEC-2G on 7606-S chassis. I installed the SPI/SPA cards in slot 3, after that I checked with "sh module" and we could see the module "OK". After this we tried to configure a VPN tunnel but we received messages in the other router about "no ipsec package".
I was checking and I tried "sh crypto engine accelerator statistic" and we got the message: " There is no crypto device".
I don't know about installation commands in references and I don't know about restrictions or configuration modes.
I have a question relating to installing lines underground in a conduit.
We've had several lines get hit by lighting which leads to the line being bad, equipment being damaged and so on. We've then installed a new cat6e cable WITH lightning arrestors which were blown almost instantly on the first storm. This is obviously a bad ground issue, and a risk to the equipment.
This being said, I would like very much to run fiber optic cable in this conduit and then convert it to ethernet, but I don't know if fiber is susceptible to lighting like ethernet cable is, OR if there are other methods to prevent this freak of nature crap!
Is it possible to install the above alfa card on mac os x 10.7.4?
View 2 Replies View RelatedI would like to learn how to install an OS like XP or linux over the network.
View 2 Replies View RelatedI am looking for the appropriate procedure for connecting an external HDD to a D-Link router with a USB 2.0 port. I am told I need to create a TCP/UDP 19540 port on my system.
View 1 Replies View RelatedI have had my new computer up and running for 2 days amd have installed 2 games but i couldnt connect to the internet because my driver installation cd says "D: is not a valid win32 application" when i try to run it and i dont know what to do i have tried resetting cd to defaults, installing manually by going in to cd files and have tried running in safe mode but nothing works .i have windows 7 home premium 64 bit OS
View 3 Replies View RelatedI'm installing WIFI for my personal business, and want to make sure my server and modem are unaccessable by WIFI users. I have the modem set to 192.168.1.1 and router(wifi) to 10.0.0.1. The problem is i can still type in 192.168.1.10 (server's ip address) or 192.168.1.1 while on WIFI and i get can still get to both.
View 2 Replies View Relatedall the drivers required to connect to the Internet wireless,,
View 1 Replies View RelatedWe have cisco 1941 as router in office, it's dhcp server, it has only vlan 1 192.168.4.0/24?I've set up 1142 ap for wireless clients How can i make it give clients ips from dhcp server from vlan 1 ?
View 11 Replies View RelatedI am trying to configure SDM 2.5 on a cisco 2600.I have access via telnet to the router and was able to change the enable password - which i think is level 15 (right?) and setup (and bring up) the ip on the ethernet interface. I can ping - and get response from - the router Trying to install SDM on the router i need to provide the default username i tried both admin/administrator but SDM can't communicate with the router?
View 21 Replies View RelatedI have a new deployment I am working on. I am unclear on the Inline setup. One location is configured as a trunk between the router and the switch, with voice and data traffic going through it. We will be installing a 294 inline at this site.What impact will it have on voice traffic? We are using G0/0 for management, not the Inline interfaces. Is that any additional configuraiton needed to inline if done this way? I didn't get prompted for vlan ID, or anything like that during the setup as an accelerator.Are these setup with default optimizations out of the box, or is there additional programming needed once they are online? I found where to build custom applications, but wonder if there is anything needed to be done once they are online for default traffic.
View 1 Replies View RelatedI've got an MSE 3310 that came with four-post rails for rack mounting. These came without instructions and we are having a hard time figuring out exactly how they work. They say General Devices C-300-S-124-RC-MOD
View 4 Replies View Relatedim trying to install a ios 12.2v on my switch. when the screen prompt it does not show me the user move symbol " SW1> ". all i see is " SW:" and from there i can not enter the commands to download from tftp server !
View 7 Replies View RelatedWe have purchased "True BusinessID certificate" from Geotrust for our SSL VPN. Geotrust issued 2 certificates such as Web Server CERTIFICATE & INTERMEDIATE CA.
SSL vpn is being configured in Cisco ASA 5510 software version 7.2(3). Now we could successfully install INTERMEDIATE CA successfully to ASA but Web Server CERTIFICATE cannot install and gives the following error
*Failed to parse or verify imported certificate*
We followed this link to install the certificatesURL
We contacted geotrust regarding this errror and they suggest to install GeoTrust Root along with the Primary & Secondary Intermediate CA certificates for True BusinessID certificate. URL
1. How to install Root along with the Primary & Secondary Intermediate CA certificates on our Cisco ASA 5510 version 7.2(3) . is there any proper way to install certificate i mean ROOT--intermediate--identify ?
2. Have we seleted the exact SSL certificate from Geotrust for our SSL VPN? is there any other certificate we should get it from Geotrust?