Cisco Switching/Routing :: 3560 BGP With 6 Digit AS Number
Sep 23, 2012
On a Cisco 3560 with IP services ver. 12.2(35)SE5 I have tried to config BGP with a 6-digit AS number, and it is not possible. What software is needed for 6 digit AS number for PI IP addresses, and do I need to buy a new switch also.
View 5 Replies
ADVERTISEMENT
Nov 24, 2010
I understand on older IOS codes If the same hsrp group number is assigned to multiple standby groups, it creates a non-unique MAC address. Is this true on newer codes like 12.2(52)SE for 3750 & 3560?
View 4 Replies
View Related
Jul 21, 2012
I was trying to upgrade my 3560 in the lab and I think I might have bricked it. I tried to load up IOS image c3560-ipservicesk9-mz.122-55.SE5.bin so I would have SSH support. I originally was running c3560-advipservicesk9-mz.122-25.SEE2.bin and now I can't get either to load, I get the error message 'magic number mismatch: bad mzip file'.I've formatted the switch and attempted to load the 122-55.SE5.bin image and got the error message above. In hope I could revert back to my old IOS I tried to load up the 122-25.SEE2.bin image but got the same error message! I've verified that the image was indeed on the flash. I'm at a loss here because I know both images are valid. I've tested them both on my other 3560's.
View 11 Replies
View Related
Oct 18, 2012
how I go about find my 4 digit code to reset the network settings?
View 1 Replies
View Related
Jun 13, 2012
Our organization currently has a Cisco 4507 acting as our core switch and 2 ASA525 firewalls.
Our existing ISP runs into our 4507. Here is the port config.
interface GigabitEthernet7/1
description ISP-DSL
switchport access vlan 10
[Code].....
We have recently purchased a 5Mbit line with a second ISP and will have the line activated tomorrow. In addition, we recently obtained our AS number through ARIN. How would I configure the second ISP to be used for load balancing/failover?
View 8 Replies
View Related
Dec 10, 2011
How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 Replies
View Related
Apr 19, 2012
I am configuring my first 2911 using a SFP card but I dont know the interface name for this module.
show inv shows the card..
What is the interface number for this card or if it needs some config before it will recognize the interface?
View 6 Replies
View Related
Mar 18, 2012
We have the need to create a large number of VLANs on one of our networks. We're talking about 60! These will all terminate on a pair of 6509-E switches (building core). We use MSTP as a standard on our network so I'm going to stick with that so that we can dramatically reduce the number of STP instances needed. However, regarding the SVIs (default gateways) is there any reason why creating 60 of these guys would be considerd a big no-no? Or would you expect the 6509s to deal with them like a boss?
View 4 Replies
View Related
Feb 17, 2007
Whether Cisco has part number for the large fan in 2811. I know p/n for small fan is already there, but I can't find any for large one( I think it s fan 3).
View 10 Replies
View Related
Oct 16, 2011
I have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !
View 3 Replies
View Related
Jan 5, 2012
If multilayer switch has routing capabilities then why we can go for dedicated router?
Why we cannot use a number for VLAN ID other than 1 to 4094 ?
View 2 Replies
View Related
Oct 30, 2012
We have IP device on the farm switch(cat6500, which is an access layer siwtch), with the gateway on the core switches (Nexus7000), on the core when I do show ip arp, I found the mac.But when I do sh mac add add of that mac there is no port attached to that mac.
Since that particular vlan only resides on the cat 6500 and two cores, so I logged in to the 6500, and when I show mac- in that vlan, I didn’t find that mac addresss. Instead, I found another mac address with last 8bit are the same of that mac.
Is it some kind VIP of the mac? How so, if no port, how can the switch forward the frame? [code]
View 1 Replies
View Related
Mar 21, 2012
Is there a CLI-command to see the serial number of the flexstack module installed in a C2960S.
View 13 Replies
View Related
Apr 30, 2013
We currently have a stack of 5 x 3750 switches and i want to remove switch number 3 (it has the least number of things plugged in). What will happen to switch 4 and 5 will they be renumbered 3 and 4, and will the config automatically update this if it does?
View 2 Replies
View Related
Jan 11, 2012
Is there a maximum number of licenses for connections to a 877?The reason I ask is that our routers are managed by a datacentre and when I asked for the login details I was told that I couldnt have them due to licensing reasons with no other explanation.
View 1 Replies
View Related
Aug 28, 2012
I have a 6509-E chassis that was prevoius in a VSS configuration. Due to some VSL failures I had to cobvert it to a standalone chassis but would like to bring it back to a virtual system.
Whenever I try to convert it by using the command "switch convert mode virtual" I get the msg %Please configure local switch number first". After doing so by entering the CLI cmd "switch set switch_num 1 local" I still get the same message.
View 1 Replies
View Related
May 12, 2012
I have configured the following access-list on routers fa0 interface (i am using 1801)
access-list 111 permit ip any any log
and applied it in "in" direction on Fa0 interface.
Now when i am sending ssh packets to this interface its showing below
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
why its not showing any port number ?
View 1 Replies
View Related
Jun 6, 2013
we have inserted into a network with VTP a Cisco Switch 2960-S, not knowing that had installed IOS LAN lite.Now I discovered that it can handle up to 64 vlan. In the network there are currently configured 62 VLAN: what happens when we exceeded the max number (64) of VLAN for that switch?
View 6 Replies
View Related
Aug 12, 2012
I found increasing number of overrun in the tengigabit interface. The hardware is 6509 with sup720-3B and the overrun output is shown in WS-X6716-10GE module. The connected device to WS-X6716-10GE is EMC Islion S200. I think the capability of WS-X6716-10GE can handle EMC NAS device and the load is not so busy. So I have no idea of handling this and the reason why this overrun packet is shown.
[Code]...
View 3 Replies
View Related
Apr 19, 2013
what is the maximum number of etherchannels i can build on a Cisco 2960S stack. We hoping to connected 15 servers using 2 port channels between two stacked 2960 for redunancey. So what is the max number of channels can i build using the 2960S? Is the max 6 or is it more?
View 4 Replies
View Related
May 15, 2012
Although I am quite used to using the WLC 4402 and the attached APs, I have no knowledge about licensing and I'm wondering if it has a limited number of AP's that can be controlled by the WLC? I'm not planning on adding 1000's but at the moment we have 21 and will probably be adding an additional 30 in the near future.
View 1 Replies
View Related
Apr 19, 2012
Cisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop" do not do the same job.
View 8 Replies
View Related
Dec 8, 2011
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
View 4 Replies
View Related
May 8, 2012
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
View 9 Replies
View Related
Apr 17, 2012
I have tried to make policy based routing on Cisco 3560. I use ipservices ios (SW version 12.2.(50)SE3 and SW-IMAGE C3560-IPSERVICESK9-M) For below configuration there is no problem and pbr is working.
“Access-list 100 permit ip host 1.1.1.1 host 2.2.2.2
Access-list 101 permit ip host 1.1.1.1 host 3.3.3.3
Route-map pbr1 permit 10
Match ip address 100
Set ip next-hop verify-availability 1.1.1.2 1 track 11
interface fasthethernet 0/1
ip policy route-map pbr1”
But when i add another sequence to the "pbr1" with another sequence number like that.
“Route-map pbr1 permit 11
Match ip address 101
Set ip next-hop verify-availability 1.1.1.3 1 track 12”
pbr is not working. Switch gives message "PLATFORM_PBR-3-UNSUPPORTTED_RMP:Route-map pbr1 not supported for Policy Based Routing”"ip policy route-map pbr1" command not shown in the running config. And "show ip policy" output is blank.Configuration guide says you have insert many sequence to the route-map with the same name. And also this command is not in the unsupported command list.
View 16 Replies
View Related
Jun 4, 2013
I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
View 3 Replies
View Related
Dec 11, 2012
I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
The configuration is
interface Vlan1
description Data VLAN
[Code].....
View 14 Replies
View Related
Apr 28, 2012
We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
View 17 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Oct 21, 2012
I have a 2504 WLC connected to a Catalyst 3560 which has multiple vlans and is connected to a 2800 series router. I know the catalyst is L3 but I am needing nat functions to get outside to the internet. From my 2800 series router I am able to ping out to the internet, also I am able to ping the vlan interfaces on the catalyst switch. Problem is from the catalyst switch I can ping the inside and outside address of the 2800 but I cannot get any further then that. I cannot ping the 2800 router gateway. Not sure what I am doing wrong as far as routing.
I've attached my 2800 and 3560 configs.
View 3 Replies
View Related
Nov 15, 2011
a number of vlan on trunk is 4096, can I limit this number? I need trunk pass only 10 vlans.
View 1 Replies
View Related
Jan 1, 2012
Clarifying whats the correct # of port asic in WS-X6704-LC?According to the following link (Catalyst 6500 Architectural white paper): [URL]
"In the WS-X6704-10GE line card, there are two port ASICs each supporting 2 x 10 Gigabit Ethernet ports"
While in the document: Understanding Quality of Service on the Catalyst 6500 Switch: [URL]
Table 10.
WS-X6704
Number of 10 GE Ports 4
- QoS on 10-Gigabit Ethernet Line Cards (WS-X6704-10GE)
So whats correct? 4 port asic or 2 port asic?
# Port ASIC’s on the linecard 4
# Physical Ports per Port ASIC 1
View 1 Replies
View Related
Jun 5, 2013
Where on the case is the serial number located? I have a dead one that needs RMA.
View 1 Replies
View Related