Cisco Firewall :: Routing Between VLans On ASA 5505?
Dec 5, 2012
I have an ASA 5505 and I have the three regular vlans, outside, inside and dmz. The best would be only have outside and inside and skip dmz, but without explenation there is not possible to have more then two clients in whats now dmz because of a mac filter on third party device.
So as security is concerned dmz and inside is equal, one to one and there should be full access between them. I ran the wizard and said that the only way traffic not should be possible to flow is from dmz to outside.
In the NAT rules the onle rule is
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
But traffic from one way or the other dmz to inside, og inside to dmz it says in log
3Dec 06 201215:38:39305006172.17.6.1053portmap translation creation failed for udp src inside:192.168.6.102/49358 dst dmz:172.17.6.10/53 From documentation I have an image with network drawing from documentation. What do I have to do allow traffic btween inside and dmz, both ways.
I have a 5505 with Base license running ASA software v8.4(2) that has been working happily for a while with an inside and an outside VLAN.
The outside has a single statically configured public IP, and I have a number of static NAT rules to expose a few internal servers as well as Dynamic-NAT for all devices on inside to gain access to the Internet... the main bits of the config are below:
I now have a requirement to add a "dmz" VLAN for guests to have access to the Internet using a dedicated wireless AP, but not to any of the inside resources. As the ASA has a base license I have configured "no forward interface" to the inside vlan, which suits the purpose fine
interface Vlan12 description Used only for guests access to the Internet - no access to the corporate resources no forward interface Vlan1 nameif guests security-level 20 ip address 192.168.2.1 255.255.255.0
My problem is that when I try to add NATing from the dmz to the outside I get a:
ERROR: Address a.b.c.d overlaps with outside interface address. ERROR: NAT Policy is not downloaded
Having had a look at the ASA Configuration guides, all the examples I can see with several "internal" VLAN's being NAT'ed use one external IP per VLAN - is this a feature/restriction of the ASA software? Are there any workarounds? Or is the overlap in the error message really about the current NATing to the inside VLAN which is done on the "any" 0.0.0.0 subnet - would the following then work:
so I look up ASA5505 licensing and for VLAN support see: 3 (no trunking support)/20 (with trunking support)*
I need 3 VLANs...inside, outside, and DMZ..but when it is creating the third (DMZ) it says I am only allowed to have 2 VLANs and can only create the third if its set to not forward traffic. ?
I planned to create 5 vlans in my cisco 3560 switch. these 5 vlans needs to have internet and needs to access Site-B.
I will write on dafault route to firewall in my cisco 3560 switch. Is ASA 5505 supports this scenario??? If it is then how to configure ASA 5505 firewall.
I've got an ASA 5505 with the Security Plus license that I'm trying to configure.
So far I have setup NATing on two VLANs, one called 16jda (VLAN 16 - 10.16.2.0/24) and one called 16jdc (VLAN 11 - 10.105.11.0/24).
From each subnet I am able to connect to the internet, but I need these subnets to also be able to talk to each other.
I have each VLAN interface at security level 100 and enabled "same-security-traffic permit inter-interface", and I have setup static NAT mappings between the two subnets, but they still can't communicate.
When I try to ping there is no reply and the only log message is: 6 Aug 21 2012 09:00:54 302020 10.16.2.10 23336 10.105.11.6 0 Built inbound ICMP connection for faddr 10.16.2.10/23336 gaddr 10.105.11.6/0 laddr 10.105.11.6/0
I have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1 nameif inside Security level 100 Ip address 172.16.100.1 255.255.255.0 [Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I am buying ASA 5505 with security license. It says it can support 20 vlans does it support 20 vlans by allowing to create subinterfaces? As it has 8 physical ports only?
I have a ASA 5505 with the security plus license. I have 7 vlans, 2 are guest vlans for wireless and wired connections. I am allowing traffic from the guest vlans to any with the http & https protocols I have ACL's in place before the allow all rule that do not allowed traffic from the guest vlans to the other vlans. Is there any way to have all traffic from the guest vlans to always go to the outside interface for the http & https traffic in stead of trying to go to the other vlans first, I know I have the ACL's in place to prevent the traffic but if I would feel better if I had this in place as well.
I have an ASA 5505 with the security plus software and I'm trying to find out how to assign 2 public IPs to the outside interface and have each IP routed to a separate internal VLAN. For example, IP 1 = X.X.X.1 routed to 192.168.1.0 and IP 2 X.X.X.2 routed to 192.168.2.0. I was told this was possible and I've been trying to find configuration examples, but I can't seem to get anywhere and now I'm getting desperate because I'm scheduled to install it this weekend.
I have 2 Vlans with seperate networks and want to create a route between one server in vlan 465 to another server in vlan 436 via port 80.Vlan 465 has a ASA 5505 inside that IP address 89.254.12.35 will be initiating the connection to address 10.200.1.213.
-Vlan 465: server address 10.200.1.213 -Vlan 436: server address 89.254.12.35
However for extended security I would like to restrict the firewall opening to an IP to IP opening.
I have set up a scenario for a small business and have some questions about how to manage the access between the VLANs. Is there is a better / another way to do it. See the attached picture for the topology / info.
My question is: My switches is set up with x numbers of VLANs and a routed port (no switch port) to the ASA for internet connectivity. How is the best (or only??) way to manage the access between the VLANs? Is it ACL's on the switch?
And by "managing access" I mean VLAN 50 (public WiFi) only have access to the internet, only management servers have access to management VLAN, Client VLAN only have RDP access to server VLAN and so on. Is there any way to do this in the ASA (or add another (gigabit) router to the topology)) or it the only way to have lots of ACL's on the switch itself? I have thought about "router on a stick", but then I imagine there will be a bottleneck between the switch and the ASA?
(Equipment is 2 x 3650G, ASA5505, AP1252 - see attached file).
WE have to deploy ASA5585 in between User vlans & server vlans. we have to find all the ports that needs to be opened on firewall. any tools to do same.
I have to put an ACL Firewall in front of a public IP range.There's no routing so I want to do it with a transparent layer 2 Firewall. I found this document which descibes exactly that feature I need: [URL]
It seems to be a feature introduced in IOS 12.3.
My Questions:
1.) is it possible use this transparent firewall feature with the 3750 Switch instead of a "normal" IOS-Based router?
2.) I've seen there is no IOS 12.3 for the 3750 but rather 12.2 (currently installed) or 15.0.1. Is this Feature included in 15.0.1?
If the feature described above is not available, is there any other way to achieve my goal?
We currently have a HP blade platform which has two Cisco CBS30X0 switches built into it running Version 12.2(55)SE. These are connected to two Cisco C2960 aggregation switches running Version 12.2(44)SE6. According to this article I need to upgrade these to 12.2(25)FX: url...
1.)This will according to that article only allow me to create edge ports on them, is this a hardware limitation or am I just not finding what firmware I need to upgrade them to, in order to allow the creation of community VLANs? We have these aggregation switches conncted directly to multiple types of firewalls which take care of each of our clients networks including internet access etc. We are wasting many VLANs and IP addresses with our current setup so I am hoping to move over to using private VLANs. The setup of the private VLANs looks simple enough.
2.)When the private VLAN's try to communicate, all info will be sent directly to the layer 3 device I gather, which will not need to know anything about the private VLANs?
routing between VLANs on my ASA 5505. I am very technical system wise, but my knowledge of routing and switching is very shallow.
What I am trying to accomplish: Small lab environment with basic services split onto two seperate VLANs (such that DHCP would need a relay on the second VLAN to deliver leases). No external network connection as of right now (so no Internet).
My current configuration: Cisco Catalyst 2960 As you can see below, the two VLANs I am trying to set up are vlan101 (10.100.100.1) and vlan102 (10.100.101.1) Code:
i have asa 5505 adaptive security plus. and i have only 3 vlans . outside , inside , DMZ restricted.so it's working fine but i want to connect to my inside another private network, or do i need to buy License.and how i can activate the license key.
I am new to the ASA so I am not completely familiar with it's ins and outs but here is the situation.I have a VPN connection that my company uses regularly. I have the VPN Pool on 192.168.18.0/25 and my Internal network at 192.168.16.0/24. My problem is that I have my phone system on 192.168.16. 254 and the only way to see it is if I change the pool to be within the same IP range as my internal network. The catch is that if I do this then that is the ONLY IP that is available to that VPN connection. Is there a way to make the 192.168.16.254 available to 192.168.18.0/25?
I am just about to buy ASA 5505. I need outside interface with Public interface that can NAT to two internal (priv)( networks. Can I have two inside interfaces, like192.168.1.0 and 10.2.0.0 that can talk to each other? Can I do it without vlans? Reason why, I would need to reconfog my current switches. On cisco web they saying that: "With the Base license, the third VLAN can only be configured to initiate traffic to one other VLAN" - but I need two inside netwroks be able talk to each other.
I have Cisco ASA 5505 Firewall with security plus license. I want to Configure 3 different subnet for inside network 10.1.x.x, 10.2.x.x and 10.3.x.x So any PC from 10.1.x.x should be able to ping 10.2.x.x So my question is that possible with ASA?? If yes than how can i configure on ASA 5505, as i know on 5510 we can configure sub interface and do intervlan routing.
I have a Cisco ASA 5505 that has been configured to act as a router as well. I have configured 3 VLANS that have access to the internet. For some reason the "InsideWifi" and the "Guest" VLANS have very slow internet speeds and sometime web pages wont finish loading properly. The "Inside" VLAN gets the speeds that are expected. The DNS server does reside on the "Inside" VLAN. Is there anything wrong with my configuration that would cause the internet speeds on the other VLANS to be slow? My config is attached.
I need to create a firewalled segment that not only separates hosts from general population, but also from each other. The solitary confinement of firewalled segments.I know that I could create a bunch of sub-interfaces, one for each host or group that needs to be isolated, but I'd really rather not have to do that if possible. 1) It could become a management nightmare between ACLs and sub-interfaces and 2) it's a waste of IP addresses.s there any way that I can create a bunch of separate VLANs behind the firewall and have them all terminate at the firewall, using a single firewall IP address for the gateway?
I am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside 2. DMZ 3. ServerNet1 4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it. [code]
Now, if I want to ping from the DMZ to INSIDE, I get an error message "no translation group found for icmp src DMZ: ...... dst: INSIDE...."
I fixed is by adding "NAT 0" onto the INSIDE interface so that packets originating from "INSIDE" that are destined for "DMZ" do not get NAT'd.
Now my question is, becasue these are all directly connected networks, how come the firewall does not route the packets, but tries to NAT them instead.
Ive been readin all over the internet (including this site) trying to figure out if the asa can handle intervlan routing. Im not sure what I am missing on my config to get this to work. Ive read that it can work and Ive read that it cant work. How to get this to work on my asa 5505.
Here is my setup
Cable Modem ---> ASA (eth0/0) (eth0/2) -->unmanaged switch for LAN connectivity (eth0/3) --> Access point for wireless LAN connectivty
My config is attached
What I would like to do is be able to communicate between vlan3(LAN) and vlan4(Wireless LAN)
Whats strange is I can RDP between the two vlans but I cant ping or anything else.
How to secure vlans on Catalyst 6500 by using Cisco ASA Firewalls?There are no free modules on Catalyst 6500 to install a FWSM module.What is the best configuration to secure vlans (~80 vlans) by using cisco ASA firewalls (context, hairpining...)?
upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
I have purchased these two switches from ebay as a test lab, I plan to connect them up via a gigastack modulecable and enable ip routing on the c3550 and vlans to talk to each other.
I'm very much a procurve person and really need to get into the cisco switching.I will want to trunklacp between the switches - whats the process is setting that up on cisco switches?
I have a 3560E with 2 vlans that I want to route between. one device with 2 vlans and route between.Interfaces are configured as such:
int g0/11 switchport mode access switchport access vlan 10 int g0/12 switchport mode access switchport access vlan 11
[code]...
Laptops on each port with 10.10.10.2 and 10.10.11.2 configured on them. I can ping from 10.10.10.2 to 10.10.11.1, but not to 10.10.11.2.What do I have to configure to be able to get the 2 laptops to talk to each other?
