I have a problem with ASA5510 CSC10 license renewing. Initially, we had CSC license with 500 seats, and renewed it to 250 seats. After that every time it shows that license expires day before today.(for example if today is 4 April it show that license expires on 3 April).
Clicking on "Check Status Online" didn't work. What can correct this problem ?
I am quite new to firewall, in my company one asa 5510 firewall is there.I configured inside, outside, dns, dhcp and nating.I need to config bandwidth limit (1Mbps) for inside port and I restruct like facebook, youtube and pornsites..And I heard that some subscription is required, really is it required?
I have a two ASA HA and I'd like to upgrade the license to ASA5500-SSL-250. I need to know if i have to purchase one license (ASA5500-SSL-250) for the Active unit and one license (ASA5500-SSL-250) for the standby unit.
We have purchased an ASA 5510 with CSC module. Unfortunatelly, white envelope with PAK for activation a Base License was lost before we managed to register it.
1) Will I be able to update firmware (from 8.2 to 8.3 or higher for example) without smarnet for ASA 5510? And what can not I do without smartnet? 2) I have only AIP-SSM-10 module to this asa 5510. is there a smartnet for it, too? And when I buy only module is there build in a 1 year subscription for IPS signatures? 3) If I have Cisco ASA 5510 base license, will my IPS on AIP-SSM-10 work? 4) Also I'm planning in a year buy one more 5510 with same module and put ther in failover. Will I really need Security Plus license for failover (Active/Standby)? For Active/Active I know that I need one, yes?
I am looking for redundant asa deployment for fail over set up . however both units have csc cards. does this product ASA5510-CSC10-K9 has license for fail over ? what's the part no for asa failover license ?
I have Asa 5510 with base license and no 3des free license installed on to it.Will it be required for both the licenses to be installed on it for site to site tunnels to establish.This firewall is not taking the below commands to give and the tunnel is not getting through.tunnel-group x.x.x.x type ipsec-l2ltunnel-group x.x.x.x ipsec-attributes.
I used to have this situation where I need to replace faulty ASA5510 (this FW did not failover to standby FW) with the new one.
But the problem is the new ASA5510 came with Base License only not with Security Plus License which is needed to allow this brand new device to be configure failover.
how do I pull out Security Plus License from old FW and switch it to new FW (Base License) and activate to Security Plus License.
I would like to order module card CSC-SSM with premium plus license but i don't know which part number with have : Plus license: Adds anti-spam, anti-phishing, URL blocking/filtering and content control
i saw part number ASA5510-CSC10-K9 but it standard license and it dont'have adds anti-spam, anti-phishing, URL Blocking/frltering and content.
I have a ASA 5510 with Security Plus License and when I looked at the devices a few days ago I had 2 contexts, however after configuring the Mgm port as a regular port the contexts show 0, why? I can not find any post on the internet where this issue has happen: here is the output from show ver:
Cisco Adaptive Security Appliance Software Version 7.0(8) Compiled on Sat 31-May-08 23:48 by builders System image file is "disk0:/asa708-k8.bin"
I have to upgrade to an ASA 5510 CSC, and the new license is generated, the file you sent me licensing, only seen this:Activation Code not required for this renewal. Please go to "Administration> Product License" in the CSC SSM console and click "Check Status Online" to get the latest expiration date (BASE: 09/04/2014, PLUS: 09/04/2014).This means that what I have not make any upgrades or license charge in the ASA? Does the automatic update is made?
What's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
we have ASA 5510 with IPS and base license. Now we need Anyconnect support for more than 2 users.
Is for Anyconnect (tunnel-mode) only the Anyconnect Essentials license enough? Do I need a license for SSL VPN peers? What about Anyconnect clientless, I see that I need a premium license? Is this one enough ASA5510-SSL50-K9? It is really expensive in comparison with Anyconnect Essentials.
Here is my sh ver output:
Licensed features for this platform:Maximum Physical Interfaces : Unlimited Maximum VLANs : 50 Inside Hosts : Unlimited Failover : DisabledVPN-DES : Enabled
We’ve ordered ASA 5510 with security plus license as below description:
ASA5510-K8 ASA 5510 Appliance with SW, 5FE, DES L-ASA5510-SEC-PL= ASA 5510 Security Plus License w/ HA, GE, more VLANs + conns
The license details on the appliance shows as the below, Fail over : Enabled Encryption-DES : Enabled Encryption-3DES-AES : Disabled Security Contexts : Default GTP/GPRS : Disabled Any Connect Premium Peers : Default Other VPN Peers : Default Advanced Endpoint Assessment : Disabled Any Connect for Mobile : Disabled Any Connect for Cisco VPN Phone : Disabled Shared License : Disabled UC Phone Proxy Sessions : Default Total UC Proxy Sessions : Default Any Connect Essentials : Disabled Bot net Traffic Filter : Disabled Inter company Media Engine : Disabled
I’ve noticed that the 3DES is disabled, do I need to order another license to use 3DES or not ?Also, I need 2 ~ 5 branches to connect simultaneously and have VPN access on their laptops to the main branch via vpn software, which VPN software I should use and is our license enough or I should order another license.
I recently picked up two ASA5510s (ASA5510-SSL50-K9 & ASA5510-SEC-BUN-K) with intentions of creating an Active/Standy configuration. I'm receiving the error message "Mates' license (2 SSL VPN Peers) is not compatible with my license (50 SSL VPN Peers)", but I was under the impression that I didn't have to buy idential SSL VPN licenses post 8.2 in an Active/Standby configuration. am I missing a step that enables the license transfer(sharing?) feature to work correctly before the failover will build correctly?
I'm currently reconfiguring an ASA5510 installation to a HA setup with a second 5510. The old 5510 has an "AnyConnect for Mobile" license which isn't being used. So we upgrade that one to a SecPlus License to enable failover posibilities and we bought a new 5510 also with a SecPlus license. When I'm trying to enable failover I get the message that my mate hasn't got the "AnyConnect for Mobile" license. I know for failover both devices must be exactly the same (at first i thougth that the AnyConnect license would be lost when upgrading to SecPlus). So now I'm wondering and searching for solutions to remove the AnyConnect license (because we don't use it).
I have a windows vista SP2 laptop, with an Intel wifi link 5100 adapter and a Realtek PCIe Family LAN adapter. From some time ago, I'm having this issue: each time I want to change network (from my job's to my home's, for example) I have to disable/enable the adaptors. This was not needed for over a year and so I own this machine, and I think It might have something to do with a network drive some IT guy in my new job installed
I've been running a cisco asa 5505 for quite some time and it has been running fine, now all of a sudden it starts to renew it's outside dhcp adress like every 2 hours. I dont think it's the ISP since I have another device connected also using dhcp to the same ISP and it doesnt renew itself, it's just the ASA. Rebooting it, makes it pick up an adress straight away. The interface seems to be up, the GUI just reports "no ip adress" and then the ASA get's a new IP after about 10-15 min without one. Pressing the renew IP adress button in the GUI throws an error.
I have a Toshiba Laptop L10 which was running a bit slow, so I downloaded the AVG PCT Tuneup 2011 package and carried out the various recommended changes including de-fragmenting disc. Now I cannot access the internet via my router and Windows cannot repair the problem as it cannot complete "Renewing your IP address". I have followed advice on this site and implemented CMD re Winsock OK, but the second step "netsh int ip reset reset.log" is not accepted; it simply returns the cursor.
my RVS4000 is not renewing DHCP lease in Auto mode. Connection lost after 24 hours.
WAN Internet interface is physically connected to cable modem - Motorola SBV6120E. Setup as DHCP server. Cisco RVS4000 is obtaining DHCP public IP without any issue, the problem is that the connection drop every 24 hours and I need to release/renew DHCP each day to be able to communicate after 24 hours. After I loose connection I need to release DHCP, the WAN interface goes down and I need to renew DHCP then. I receive the same IP address and connection is againg UP and working.
tried to load new firmware and also setup the router with default configuration, but without any change. as there is no auto-reboot function, it is really annoying to log into managment interface each day. I also loose remote access after 24 hours, so I am not able to access the rotuer from outside. My local provider do not support static public IP on WAN, therefore I have to use DHCP.
I purchased the license P/N: ASA-CSC20-250U-1Y with Description: ASA 5500 CSC-SSM-20 250-User License Only Renewal (1-year)
But I had a mistake because I need support to 500 users. Now, to solve my mistake I want to know Do I can purchase another ASA-CSC20-250U-1Y to provide the 500 users suppor?
I mean, ¿are two (2) ASA-CSC20-250U-1Y equivalent to the 500 user license listed below?P/N, ASA-CSC20-500U-1Y with Description: ASA 5500 CSC-SSM-20 500-User License Only Renewal (1-year)
Started this morning woke up checked my phone no wifi hmm weird checked my hp tpuchsmart connected but jo internet access checked my router(netgear wireless N 300) made sure my modem and all wires are connectedNext went to my router ip 192.168.1.1 after reading some forrums i thought maybe if i changed the ip or sum i would have worked i know dumb though.. any way i believe i disabled my dhcp.. and one of the ip ad on the same page to 192.168.1.3 thats when it got worst i tried ipconfig/release saysNo operation can be performed on bluetooth network connection 2 while it has media disconnected.No operation can be performed on local area connection while it has its media disconnected(Its a wireless connection from my touchsmart to my router) I have tried goin back to the routers page but i can no longer find itI have also tried ipconfig/renew but i get this...No operation can be performed on bluetooth network connection 2 while it has its media disconnectdAn error occured while renewing interface wireless network connection : unable to contact your dhcp server. Request has timed out.No opration can be performed on local area connection while it has its media disconnected
I’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other. - I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit. - So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
i have CSC-SSM-20 i want to renew the license to support 750 users for 3 years if i have base license only and if i have base and plus as bundle?i want to know the steps and also the part numbers and what is the difference between these two part numbers
ASA-CSC20-750UP-1YASA 5500 CSC-SSM-20 750-User w/ Plus Lic. Renewal (1-year) ASA-CSC20-750P-1YASA 5500 CSC-SSM-20 750-User Plus Lic. Only Renewal (1-yr)
My customer is asking to see the license for the SSM-10 card how do i access the card to show this information. the Firewall unit has a base licence installed.
I'm new to ASA and bought a used one from ebay but I cannot connect to the ASDM - I get an error in all the browsers.
Cannot communicate securely with peer: no common encryption algorithm(s).
(Error code: ssl_error_no_cypher_overlap)
Having browsed the support forums and Google - it seems I need the 3DES license. I have obtained an activation key from Cisco and applied it to my ASA 5505 however I get a warning about the device is licensed for a higher software level. the license on the ASA is Security plus. When I apply the activation key from Cisco most of the features are disabled.
I have 10 user license for Cisco ASA, i have to use this ASA for client connectivity. Can i do NAT of more than 10 users with this license? What i understand is NO.
But as per Below explaination looks like, i can if i am not doing default routing? Actually i just need to add a specific Route towards client DMZ interface on my ASA, no default route, so can i use more than 10 concurrent sessions with this license?
Do I need the security plus license to do HA with two 5520's?I was told by our purchasing department that the 5520 was supposed to be able to do HA out of the box, but when I look I see only the VPN + license. Does that mean I can download the security plus license? Or do I even need it on the 5520.