Cisco WAN :: Does 1841 Supports 10MB ILL Link
Feb 13, 2011
We have a 10 MB Internet Link coming from our ISP through there MUX.The link is connected to our Router 1841.Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)From past few weeks we are facing link speed issues. It gives not more then 1-2 MB.The ISP is telling there is no Problem in there network. We have kept Default Routing pointing towards there IP.We want to know whether our router will support 10MB Internet Link or Not.
View 9 Replies
ADVERTISEMENT
Jul 18, 2011
We have a MWR2941 (running 12.4(20)MR) router on site A and one in site B which will be connected over a Service provider L2VPN Ethernet over MPLS (EoMPLS) Network, with 10Mb Bandwidth allocated by the ISP. I have simulated this in the lab by directly connecting the two MWR's back-to-back via the Gig0/0 interface with configurable bandwidth of 10Mb on the Trunk interface.
The E1 TDM pseudowire end to end is working fine, with PTP configured for E1 timing/clocking. In addition I have a 2960-24PC-L switch connected on G0/2 of the MWR (on each end) configured with dot1q trunking. The switch will be used to connect two user groups in two seperate vlans (VlanA and vlanb) and transported across the same 10MB wan Link. Below are the requirements
1) Classify and mark Psuedowire packets E1-DATA coming from a E1/CEM interface and give it priority treatment over the WAN Link with reserved bandwidth of at least 4MB
2) Classify and mark Signalling/Timing PTP packets coming from PTP Vlan and give it strict bandwidth reservation over the WAN Link of 1MB
3) Classify and mark vlan A traffic coming from the 2960 Switch Trunk port (Connected to G0/2 on MWR) and give it bandwidth reservation over the WAN Link of 2MB
4) Classify and mark vlan B traffic coming from the 2960 Switch Trunk port (Connected to G0/2 on MWR) and give it bandwidth reservation over the WAN Link of 2MB
It is important that the E1 Traffic and the Signalling/Timing PTP packets are given priority and strict reservation so that it is not dropped in times of congestion. At the same time Vlan A and Vlan B need bandwidth reservation to give them their guaranteed bandwidth.
Currently I have tried applying policy map to the CEM interface. However, I am having trouble matching anything on the CEM input. Also I am having trouble applying a service-policy outbound on the gig0/0 (WAN Link). Also I can’t apply a service-policy inbound on the Gig0/2 interface with match statement. I have tried configuring input policy map to classify and mark PTP traffic (Vlan 902), but the MWR does not also allow me to attach a service-policy to the vlan interface. how to configure the MWR and have a workable QOS solution.
View 2 Replies
View Related
May 28, 2011
Today I read a comment on a review of DIR-615 [URL], saying it supports only 32 concurrent connections where as other routers support more than 200
View 6 Replies
View Related
May 29, 2012
Originally I owned an Aztec router which supports a DSL Cable which my internet provider gave us but now that I bought a new router I didn't know that the MR3420 only support WAN cable what should I do? like find a dsl to wan cable (doubt it exist) or ask from my internet provider or return the router?
View 1 Replies
View Related
Mar 31, 2013
Region : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version :
ISP :
The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.
View 4 Replies
View Related
Oct 29, 2012
Region : UnitedKingdom
Model : TL-WR841N
Hardware Version : V8
Firmware Version :
ISP :
I'm interested in purchasing this router but I need to know how many clients it supports. We currently have a normal adsl wireless router but after about 20 clients it stops accepting anyone new.
View 3 Replies
View Related
Jan 29, 2013
Region : UnitedKingdom
Model : TL-WR841N
Hardware Version : V8
Firmware Version :
ISP :
I'm interested in purchasing this router but I need to know how many clients it supports. We currently have a normal adsl wireless router but after about 20 clients it stops accepting anyone new.
View 1 Replies
View Related
Apr 9, 2013
how many users supports the 2600 series ap air voice, video, and data average any document or link
View 3 Replies
View Related
May 20, 2013
If IAD 2432 can support a 10Mb Internet Connection?
View 6 Replies
View Related
Mar 13, 2012
We have a new 100MB internet service, but we only pay for 10MB and above that is a per/MB fee and not cheap. I want to limit all traffic inbound and outbound only to use up to 10MB on the outside interface of our Cisco 3825.
View 9 Replies
View Related
Feb 1, 2011
I was unsure whether to post this in networking or the XP forum. I am fairly computer literate, but have hit a stumbling block.
For over the last month I have been getting download speeds of 1-2mb on my 10mb connection via speedtest and other speed checkers. However, if I use safe mode, I get 10mb straight away. Virgin Media (my ISP) have been out and plugged a laptop into my connection and they get 10mb straight away.
I have tried both IExplore and Firefox. I have zonealarm firewall and avast antivirus. I have ran a boot-time AV check. I have also ran spybot and malwarebytes which all found nothing.
I have tried completely disabling my anti virus & firewall and running speed tests - still the same. I have tried using msconfig and disabling all but core components - still the same.
My pingtest just came up with this:-
Packet loss test: FAILED (I do have java installed), fails on IExplore and Firefox.
Ping: 895ms
Jitter: 1413ms
View 5 Replies
View Related
May 18, 2012
Second laptop attached to cisco 10mb port with an IP address of 10.18.158.200 and the cisco interface 10.18.158.254.Okay, here is what is happening and I cannot work it out.If I ping, from Laptop 1 to the cisco subinterface on 192.168.94.253 it is succesful. If I ping from the 1721 to Laptop 1 it is successful. I see the VPN come up and the rulebase on the junipers show the traffic flowing across (ICMP).If I ping, from the 10.18.158.254 interface via telnet on the 1721, I can ping all the way through to 192.168.194.254, which is the gateway for Laptop 1.
View 1 Replies
View Related
Jul 29, 2012
I am using Cisco ASA5510 Firewall in my network. Upgraded the Memory and Flash to 1GB and 512MB.But the 5 interfaces ports are 10mbps.Can it possible to upgrade the module of Interfaceses from 10mb to 1gb?
View 2 Replies
View Related
Dec 27, 2011
I'm using E4200 (fw 1.0.03) as AP and EDIMAX 6675nD as a client. I can't get over ca 10MB/s data througput even there aren't any other communication loads. Test conditions are: 5GHz band, no other networks in the band, distance 2m without any obstacles, no other data transfers (except the test), data source is NTB on GLAN port of Linksys, data sink is NAS at GLAN port of Edimax, test file is 0.5GB file. The NTB and NAS doesn't seems to be a bottleneck, because NTB connected directly to the Edimax does over 50MB/s. Both the E4200 and 6675nD are (should be) capable of 450Mbit/s @ MCS23. Strange thing is that none of them allows setting of MCS23 in their manual settings. It ends with MCS15. While forcing the E4200 to a specific MCS (in the hidden wireless_advanced menu) the MCS15, 14, 13 and auto give very similar results. The throughput drops by MCS 12 and lower indexed MCSs.The 10 MB/s seems to be a low number.... and (based on internet forums) I'm not the only one fighting the magic number 10MB/s. What is the reason of the ca 10MB/s bottleneck? And the resons why both of the routers are quiet about the MCS16 to 23 schemes in their menus, while their labels aren't?
View 4 Replies
View Related
Jun 26, 2012
We are upgrading our incoming Internet service from 30 Mb 10/100 to 100Mb 10/1,000.Will my 2600 series router support the 10Mb 10/1,000 traffic from my new modem?Do I need to change my interface speed from 100 to 1,000? I to be sure my router will support the upgrade. [code]
View 8 Replies
View Related
May 28, 2012
I am now having trouble to buil a vpn ipsec on an adsl link, my architecture is as follow:
[code]...
whith this output, debbuging seems very difficult. see attached my configuration on router 1841
View 3 Replies
View Related
Apr 2, 2012
It is required to monitor newly placed WAN link performance . How can I configure my cisco 1841 router to obtain the following information.
1) Errors
2) Jitter
View 5 Replies
View Related
Feb 19, 2012
is there any known issue in configuring multilink ppp using an old WIC-1T and a newer HWIC-1T on the same Cisco 1841 router ?
View 2 Replies
View Related
Sep 19, 2011
I am having some trouble configuring dual NAT on a Cisco 1841.
The 1841 has three interfaces.
Fa0/0 - LAN
Fa0/1- Different private network
Fa0/1/0 - Connection to DSL modem
NAT overloading is configured on Fa0/1 and we have traffic that must be router there. We would like to have all internet access go through the DSL modem. Currently internet access is obtained through fa0/1 but is not ideal. I have floating static routes configured if the DSL link goes down. (Which is currently unplugged) I do not have physical access to the router at this moment. We would like to keep the config a simple as possible. It seems like route-maps may be one of our only options.
View 1 Replies
View Related
Dec 19, 2010
We want to terminate new 10M link via Ethernet interface on Cisco 1841 router. We have free Gig port on the router. We also have HWIC-FE module inserted in the router. However, our implementation team said that Cisco 1841 doesn't support 10M link. It is not designed to cater to such high Bandwidth.
View 14 Replies
View Related
May 19, 2011
Cable modem into cisco-linksys E4200. 2 of the ports going out from the router plug into the wall, where one goes to the master bedroom and one goes to the living room. Once it gets to the wall jack in each of those rooms it goes out to a gigabit switch. Each of those two rooms has a computer and a TV connected, and the living room as a blu-ray also connected to the switch.The third port going out from the E4200 router goes to another gigabit switch, which is connected to a couple more computers in that room.All of the cables are either cat5e or cat6. The long cables running through the wall from the server room to the living room and master bedroom is 24gauge 4pair cat5e, it was run by a general contractor.
When I transfer between any of the computers on the network as it sits I get 11MB/sec. I get that number by clicking more details on the file transfer. In the network tab of task manager it sits pretty consistently at 10%.If I move any of the computers to be connected to the SAME switch (i tested all 3) i can transfer around 60MB/sec.Based on this testing my initial instinct is to say that the cable running between the rooms is limiting the transfer speed. However the cable is cat5e and rated for gigabit. Neither of the runs are anywhere near 300ft long. Plus the consistency of the transfer speeds at 11MB/sec makes me think it's being clearly capped at 100base-T speeds as opposed to just slowing down due to interference of the cable.As a side note there is a place in the router that tells you the speed of each port. For some reason it has one of my ports listed as gigabit and the others listed as 10/100Mbps. The yellow 3 foot cable i have is listing as gigabit, when i swap it with another cable in the router it changes the gigabit port to the one this yellow cable is on, very odd, however regardless of whether the router says its gigabit it only transfers at 11MB/sec anyway.What I'm wondering is what could be causing this limitation besides the two cables running through the wall? Is that the only thing that could be doing it? What is the best way to really test it out? Do I need to buy some kind of network testing device that tests throughput?
View 4 Replies
View Related
Jan 6, 2013
i have a Netgear N600 Wireless ADSL2+ router on wireless a/b/g/n dual band and all that but what i want to know is will i get better performance if i use a WirelessN card over G on a 10 - 15mb/s connection gaming wise and will it b a great increase over the G causeif its not a HUGE increase then i wont waste my money on a newer card?
View 3 Replies
View Related
Aug 9, 2011
Is Ciscoworks LMS 3.2 supports WISM 2?
View 3 Replies
View Related
May 20, 2013
I am getting error message in my cisco 1841.I am using E1 card and next end is terminated to modem(e1 to V.35) and its connected to router serial port.
i have configured at both end but status in not comming up in E1 interface.Also geeting this message %CONTROLLER-2-FIRMWARE: Controller E1 0/0/0, firmware is not running".
View 4 Replies
View Related
Sep 4, 2012
Which version of IOS for the 2621 supports NAT?
View 1 Replies
View Related
Apr 11, 2011
the max amount of AP's one 5508 WLC can support ?
View 4 Replies
View Related
Jan 6, 2011
Imagine on a 3845 router, I need to bond 2xDS1 circuits (for a Metro Private Line, point-to-point circuit). I have done that multiple times for NxT1s with MLPPP - OK.So my question is, is the card below and MLPPP valid for 2xDS1? I read all the product specification and it always mention "T1", but it does not officially say I can configure DS1.VWIC-2MFT-T1-DI#Two-port RJ-48 multiflex trunk - T1 with drop and insert
View 1 Replies
View Related
Apr 29, 2011
I have 2611xm router with 2 fastethernet ports. Now I want to install NM-1FX-TX module. I just want to conform that does 2611 supports NM-1FX-TX module. I am using this device for lab purpose. I am using latest IOS"
View 2 Replies
View Related
Aug 30, 2011
I am interesting is ESW-520-24-K9 switch supports GLC-LH-SM SFP? In official data sheet there is no information about that. it is supported and I am interesting if it is true ?
View 5 Replies
View Related
Oct 19, 2012
any 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.
View 4 Replies
View Related
Feb 8, 2013
We are using Cisco 1941 Router as CPE where we wanted to trap CPU, Memory & ISYSTEM MIB. The same we are achiveing using SNMPV2 but when we tried using SNMPV3, there is no response for these MIBs.
We tried to configure SNMPV3 using below Link but still there was issue. There was response fr [URL]
Wanetd to know SNMPV3 MIB are supported for Cisco 1941 Router IOS Code universalk 15.2(3)T1 & Data License. When we tried using Cisco IOS MIB Locator, we are not able to see any MIB for SNMPV3. whats is that mean. Does this Platform + IOS Support SNMPV3 or not.
Below is the Snapshot from Cisco IOS MIB Locator for said image.
[Code]......
View 3 Replies
View Related
Jan 22, 2013
I have a small network of about 12 Mac's running OS X, about 20 or so iOS devices and a OS X Server. Currently i have a Cisco SRP547W which works fine when we're all wired in, however we have connection issues when trying to access the server over Wi-Fi. I'm lead to believe that this could be a result of the lack of support for Bonjour within the router. What might be a solid alternative?
View 1 Replies
View Related
Jun 28, 2011
We are using the Cisco ACS 5.2 for AAA to manage our network devices. We plan to migrate all our edge's devices to IPv6 soon. Can or when the Cisco ACS 5 support IPv6 address?
View 1 Replies
View Related
