I have 2611xm router with 2 fastethernet ports. Now I want to install NM-1FX-TX module. I just want to conform that does 2611 supports NM-1FX-TX module. I am using this device for lab purpose. I am using latest IOS"
View 2 RepliesI was given an old Cisco 2611 to screw around with, no idea if it's working or not and no idea if the configs and passwords were wiped. Now my problem is that when I turn it on I don't see any console output at all.
Using 9600 baud, 1 stop bit, 8 data bits, no parity or flow control.
The power LED comes on and the activity light blinks for ~1 - 2 minutes before stopping. If I plug something into one of the Ethernet ports on the back the link light comes on for the port and the activity light occasionally flashes, from DHCP probes or something from my netbook I assume.
i was just wondering if its possible to use a WIC-4ESW with a 2611 non-XM router?
with any IOS versions, i just want to know if its possibly or not.
A broadband speed test take before the Cisco 2611 shows 25+ Mbps. After the 2611, it drops to under 6. Consistently. The router routes between the local LAN (10.80.0.3) and a remote building across (10.13.0.2) a T1. The ADSL internet connection enters this router and leaves to a Cisco 3550 switch.
View 13 Replies View Relatednow currently i am working in networking academy. here we are using cisco 2611 and 1761 routers, i want to setup these two routers, i know the all configuring commands,
View 1 Replies View RelatedWe have an aging 2611 router that that we need to replace due to the fact that its 10Mb/s Ethernet ports are limiting our internet connectivity throughput (we have a 20Mb/s circuit).
The purpose of the 2611 router was to route traffic from multiple devices connected to a 2950 switch's VLAN X to the internet. Can we achieve this same functionality with only a 3750C-48TS-S switch? Could a static route statement on the 3750 replace the need for the router?
my cisco 2611 series router is showing garbage value at start up and not allowing me to enter in Romon mode I check the bitrate in console .it is 9600/8N till then i am unable to start the router Can you tell me how to change configuration register value without entering in rommon mode
View 6 Replies View RelatedPhase1 is complete, Phase2 isn't coming up...everything has been verified on both sides but we're getting unknown errors.
Aug 17 11:33:15.609 CDT: ISAKMP (0:2): Old State = IKE_QM_READY New State = IKE_QM_I_QM1
Aug 17 11:33:15.609 CDT: ISAKMP (0:2): Input = IKE_MESG_INTERNAL,
[Code].....
i have Cisco 2611 series router it is showing garbage value while start up as 00000000000000000000000200000000000000 and i am unable to log in it Roman mode.
View 1 Replies View RelatedI'm trying to connect my Cisco lab to the internet. I've configured my 2611 to accept DHCP. I can ping the Linksys E1000 router but can't ping the modem on the other side, and cannot get out to the internet with the PC that's connected to the lab. When I look at the DHCP table in the E1000 the 2611 shows up in the table. I can ping all other computers on the lan, just not the modem to get out to the net.I have the configuration for the 2611. Did I miss something. Is the modem blocking ICMP traffic?
Router#sh run
Building configuration...
Current configuration : 931 bytes
!
version 12.3
service timestamps debug datetime msec
[code].....
I have a wireless access point, I want to be able to hand out addresses via the Cisco router through DHCP on the interface eth0/1. The wireless users that get an IP I want then route out the eth0/0 interface to my statically assigned default gateway. Right now Im not concerned with setting up security measures once this works I'll go back in and add that. Here is my running-config. Right now nothing from the 10.0.0.0 is being routed out to the internet.
View 6 Replies View RelatedI got some unexpected System crash, and this happens to 2 different routers on the same network.. (We suffer a Crash and change the router, happens the same to the new router after some time, maybe 40 minutes!!)
Here is the last console report for the new router....
%Software-forced reload
Preparing to dump core...
4w1d: %SYS-2-WATCHDOG: Process aborted on watchdog timeout, process = IP NAT Age
[Code]....
I have one Cisco ASA 5510 with 2611 router two 2960 switch how to configure.
View 1 Replies View RelatedI am with Virgin media and have a home lab (2611 routers, 3550 switches, 2950s etc) which i usually just use for testing things on and practicing.
Now I tried to connect it to the internet and got some weird things happening.
I got NAT and DHCP client all setup correctly on the router (or so I think!) along with DNS settings but I still can't get Internet access.
My network is all setup right so that through using OSPF the router is the gateway (0.0.0.0 route) for all devices. Doing a traceroute confirms this.
Yet I never get any further than the router? I see IP nat translations ticking up as I send more requests but never get a webpage or a reply from any of the machines in my network.
HOWEVER... The router itself does get some replies from Google.co.uk and bbc.co.uk but doesn't seem to want to give anything else on the "inside" a response?
Here is a dump of config:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
My home lab is in a different room than the cable modem. I have a wireless N router in the room with the cable modem. I have a wireless access point that is connected to a Cisco 2611XM routers fa0/0 interface. The 2611 accepts the DHCP address from the wireless router. However, I can't ping past the wireless LAN 192.168.10.0 network. I know with the wireless router it's two layers of DHCP. Should remove the DHCP settings from the wireless router? The wireless router is a TrendNet TEW-651BR. I can ping my iphone or any device conntected to the wireless router. And my laptop can ping default gateway of the wireless router, which I assume is the cable modem, however the 2611 cannot. So I'm assuming that's why the hosts behind the 2611 can't get to the internet. I followed the below instructions. I know the instructions don't assume your using a wirelss router between 2611 and the cable modem. But, I really don't want to run a cable to the cable modem.
[URL]
I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies View RelatedI'm in an issue w/ on of our ISPs. We're using an ADSL line as a secondary light load line ( 16 MBit, /w PBR in place to separate the 80 and 443 from the business-critical applications running via a SDSL link. ).
I am on a 2611 XM with IOS 12.2, mated to a D-Link 321B modem running in transparent mode. After running smoothly for weeks, for a few days now, every night some time between 2 AM and 4 AM the link would die with the dialer showing:
Virtual-Access1 is up, line protocol is down Hardware is Virtual Access interface [code]....
To my knowledge, the only option to bring it up again is to reload the box . Taking into account that the router is our DHCP server and the date gets reset to 1994, interesting effects are the outcome of resetting the box.
Well, the ISP have checked their gear and keep saying that these report a "port error" ( quite unspecific ) and blame me that I have a wrong. config in place - which is here:
interface Dialer2
description ecotel Bridge
ip address negotiated
no ip proxy-arp
[code]...
Is Ciscoworks LMS 3.2 supports WISM 2?
View 3 Replies View RelatedWhich version of IOS for the 2621 supports NAT?
View 1 Replies View Relatedthe max amount of AP's one 5508 WLC can support ?
View 4 Replies View RelatedImagine on a 3845 router, I need to bond 2xDS1 circuits (for a Metro Private Line, point-to-point circuit). I have done that multiple times for NxT1s with MLPPP - OK.So my question is, is the card below and MLPPP valid for 2xDS1? I read all the product specification and it always mention "T1", but it does not officially say I can configure DS1.VWIC-2MFT-T1-DI#Two-port RJ-48 multiflex trunk - T1 with drop and insert
View 1 Replies View RelatedI am interesting is ESW-520-24-K9 switch supports GLC-LH-SM SFP? In official data sheet there is no information about that. it is supported and I am interesting if it is true ?
View 5 Replies View Relatedany 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.
View 4 Replies View RelatedWe are using Cisco 1941 Router as CPE where we wanted to trap CPU, Memory & ISYSTEM MIB. The same we are achiveing using SNMPV2 but when we tried using SNMPV3, there is no response for these MIBs.
We tried to configure SNMPV3 using below Link but still there was issue. There was response fr [URL]
Wanetd to know SNMPV3 MIB are supported for Cisco 1941 Router IOS Code universalk 15.2(3)T1 & Data License. When we tried using Cisco IOS MIB Locator, we are not able to see any MIB for SNMPV3. whats is that mean. Does this Platform + IOS Support SNMPV3 or not.
Below is the Snapshot from Cisco IOS MIB Locator for said image.
[Code]......
I have a small network of about 12 Mac's running OS X, about 20 or so iOS devices and a OS X Server. Currently i have a Cisco SRP547W which works fine when we're all wired in, however we have connection issues when trying to access the server over Wi-Fi. I'm lead to believe that this could be a result of the lack of support for Bonjour within the router. What might be a solid alternative?
View 1 Replies View RelatedWe have a 10 MB Internet Link coming from our ISP through there MUX.The link is connected to our Router 1841.Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2)From past few weeks we are facing link speed issues. It gives not more then 1-2 MB.The ISP is telling there is no Problem in there network. We have kept Default Routing pointing towards there IP.We want to know whether our router will support 10MB Internet Link or Not.
View 9 Replies View RelatedWe are using the Cisco ACS 5.2 for AAA to manage our network devices. We plan to migrate all our edge's devices to IPv6 soon. Can or when the Cisco ACS 5 support IPv6 address?
View 1 Replies View Relatedi have two cisco 2800 routers , and i have three different networks , so can cisco routers supports more than one private network example,My First location i have one public connection of 200.100.100. 1 and private network of 192.168.1.x network and the second router i have one public connection of 200.100.100.10 and two private networks of 192.168.50.x and 192.168.60.x , So can i route my first location to this two different networks , because my router have only two FastEthernet connection , so how it's possible or not.
View 3 Replies View RelatedI have some questions about the size of the certifcates in ACE module (ACE20). Reading the following link: [URL]
I can verify this text: 4096 (high security, level 4) - For software release A2(2.4) and later in the ACE module and software release A3(2.6) and later in the ACE appliance, you can use 4096-bit SSL certificates in chaingroups and authgroups. You can also import public certificates and keys that are 4096 bits in length.
We intend to use a certificate (CA) with keys of 4096 bits and according to the text of wiki, it's possible.
But if I check the guide [URL]
Somebody that already use certificates with 4096 bits in ACE20 module?
whether Cisco GSS 4492R supports NTP authentication. GSS Software version : 4.1.0.0.28
View 1 Replies View RelatedWhen we say that ASA 5505 supports 10k connections does it mean that we can have 10k connections to the different websites?
View 5 Replies View Relatedi have VWIC2-2MFT-T1/E1 card installed in 2821 ISR router, ios (C2800NM-SPSERVICESK9-M), Version 12.4(25d).does this IOS supports unframed G.703 and also does this card VWIC2-2MFT-T1/E1 supports unframed????
View 9 Replies View RelatedIf one has internet and phone service through Cable, I know you can buy your own modems and routers, but is there a particular kind of modem you'd need to get to support VOIP for the phone?
A friend of mine has phone through Cable and her internet and phone suddenly stopped working, although her TV service is fine. We are thinking that maybe the cable company's modem is bad, so she wants to buy her own modem, but we're not sure if it needs to be a particular type of modem. I've looked around for her, but haven't found anything in modem specs stating they support VOIP. Does it matter? Or can you buy any cable modem?
We already looked at the cable providers website to see their supported modems, but they are all the same brand as the one she has that doesn't work. She already has a wireless router, which she will plug into the modem she buys, so we're only looking for answers regaring a modem.