Home Network :: Connecting Cisco 2611 To Linksys E1000?
Aug 3, 2011
I'm trying to connect my Cisco lab to the internet. I've configured my 2611 to accept DHCP. I can ping the Linksys E1000 router but can't ping the modem on the other side, and cannot get out to the internet with the PC that's connected to the lab. When I look at the DHCP table in the E1000 the 2611 shows up in the table. I can ping all other computers on the lan, just not the modem to get out to the net.I have the configuration for the 2611. Did I miss something. Is the modem blocking ICMP traffic?
Router#sh run
Building configuration...
Current configuration : 931 bytes
!
version 12.3
service timestamps debug datetime msec
[code].....
View 3 Replies
ADVERTISEMENT
Mar 11, 2012
My home lab is in a different room than the cable modem. I have a wireless N router in the room with the cable modem. I have a wireless access point that is connected to a Cisco 2611XM routers fa0/0 interface. The 2611 accepts the DHCP address from the wireless router. However, I can't ping past the wireless LAN 192.168.10.0 network. I know with the wireless router it's two layers of DHCP. Should remove the DHCP settings from the wireless router? The wireless router is a TrendNet TEW-651BR. I can ping my iphone or any device conntected to the wireless router. And my laptop can ping default gateway of the wireless router, which I assume is the cable modem, however the 2611 cannot. So I'm assuming that's why the hosts behind the 2611 can't get to the internet. I followed the below instructions. I know the instructions don't assume your using a wirelss router between 2611 and the cable modem. But, I really don't want to run a cable to the cable modem.
[URL]
View 5 Replies
View Related
Dec 25, 2011
Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 2 Replies
View Related
Aug 3, 2011
Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 3 Replies
View Related
Dec 27, 2012
I am trying to determine the best option for extending my home network. I am currently running an E2000 as my router and am considering the purchase of a Valet Plus to use as only an Access Point. Alternatively I have a used E1000 in good condition. Which would be best for use as an Access Point only?
View 1 Replies
View Related
Jan 17, 2013
I have an AirPort Express set up as my router, and that works fine and is the main network that I use. I also have a Linksys WRT54GL that is wired to a printer.Currently, when I want to print from my computer, I have to manually connect to the Linksys network, which is a pain. I would like to wirelessly connect the Linksys to my main network, so I can print even when connected to my Airport Express.Does that mean that I have to configure the Linksys as an access point? A bridge? Something else? How do I do that?
View 8 Replies
View Related
May 2, 2012
I have a Comcast Router pushing out IP's in the 10.1.10.X range. I want to hookup a Linksys E1000 Router so I can use its wireless & Guest access features. The Linksys is using the 192.168.1.x range. I have a cable from the comcast router running into the Internet port of the Linksys. I have tried changing the Linksys router IP to 10.1.10.x and turning off DHCP. It will not allow me to the internet nor allow the PC connected to it to connect to the PC that is attached to the Comcast Router. I cannot replace the Comcast as it is a combi router/modem.
View 2 Replies
View Related
Feb 16, 2011
i need to connect a linksys e1000 to an existing dlink router. i have tried several solutions that i have found on the internet, but none have worked. i need DETAILED instruction tailored to e1000 specifically because i am having trouble with dhcp definitions as i have not done this in years. i can get it to work, but i have to maintain security and everything i have done still allows me through to dlink router.
View 6 Replies
View Related
Aug 23, 2011
why I am only able to connect at 39Mbps (often 5.5Mbps) to my Linksys E1000 Router? Residential. Wood Frame/Stick home construction. No other devices connected to router. <10 feet from E1000 Router. Line of sight (nothing in between router/laptop). New Dell Inspiron DW 1501 Wireless-N WLAN Half-Mini Card.
E1000 Network Mode: Mixed
Channel Width: Auto (20MHz or 40MHz)
Firmware: 2.0.01 build 08
At times I have seen it flash to 52Mbps but immediately drops to 39Mbps or lower (26, 5.5, etc.).Sales prop indicates up to 300Mbps. Where is the other 90% of the connection speed they’re talking about? OR is 39Mbps expected?
View 1 Replies
View Related
Mar 30, 2012
Is it possible to connect my Cisco E1000 to a Linksys Wireless G Router?
View 8 Replies
View Related
Dec 27, 2011
I'm trying to connect my Nook Tablet to my wireless E-1000 router. I'm using a cable connnection for internet service. THe nook will find the network indicating "excellent" signal , but when it goes to authenticate it disconnects. After reading about WEP security, I switchedecurity setting of the Cisco router to "WPA Personal". Results are the same.
View 1 Replies
View Related
Jan 24, 2013
I have a 2wire wireless router and I would like to connect the e1000 in another room as a AP(access point).
View 2 Replies
View Related
Jan 24, 2013
I have a Linksys E1000 router just upgrade to the latest 2.1.0.2 firmware...I have a PPPoE connection which used to run smoothly on the router..however off late...suddenly the router stopped connecting..it always shows "connecting" in the status tab of the router page...and eventually says failed to obtain IP address...however when I attach the cable directly into my PC it works just fine.I also had a word with my internet provider...he's kept the MAC open (or something like that) so he said that isn't the issue and he keeps saying there must be some issue with the router. However, occasionally the router DOES connect for half hour or so and then just refuses to connect again !..
View 2 Replies
View Related
Feb 8, 2012
I've got an issue with my router. The Linksys E1000.In my opinion it supports the Wireless-N mode, so does my wireless lan card which is the Atheros AR5B93 (also known as the Acer Nplify 802.11 b/g/n). When I connect to the router, it only connects in normal wireles mode, so no b,g or n mode. But when I look at the Client Tabel of the router all other devices connected to the router are in Wireless-G mode. Even my laptop doesn't connect in Wireless-G mode.I want to have my laptop connected in Wireless-N mode. What do I have to do, to make this working?
View 7 Replies
View Related
Apr 17, 2011
Connecting PS3 to Playon in a difficult structured network?
View 1 Replies
View Related
Jul 1, 2012
I'm running into an issue with allowing all the PCs to use the one printer connected to devpc. I have a westell 7500 from CenturyLink and a Belkin Wireless G router. This is the layout:
View 6 Replies
View Related
Feb 15, 2013
Is there any way to disable router devices from connecting to your network? For example I want people to connect ethernet cables to their laptops, ps3s, pcs, etc but not to routers. How would one go about doing that?
View 1 Replies
View Related
Jun 20, 2012
I've got a 2600 that I am wanting to connect to my cable modem. However I don't have the knowledge to get it running. My ISP uses a dynamic IP and I am unable to get it to connect.
ROUTER#show run
Building configuration...
Current configuration : 685 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
[code].....
View 7 Replies
View Related
Jul 18, 2012
How two PC's can be connected directly for sharing data and resources? What should i use to connect two or more PC's(switch or hub)? Are patch cord and crossover cable the same thing?
View 3 Replies
View Related
Apr 17, 2011
I recently set up a VPN on my home computer. I am wondering if it is possible for me to connect to the internet via the VPN without also being connected to the internet via my home wireless network? Right now, whenever I disconnect from my home wireless network, my connection to the VPN will also cut off. This is a problem because should my connection via the VPN ever be interrupted, my home wireless connection would then "take over" the connection, and the eb sites I'm visiting would then be able to see my real IP address, which makes having a VPN pointless. I'd like to have it so that if my VPN connection is interrupted, I will simply not have internet until the VPN connection comes back.
I am running Windows 7.
View 8 Replies
View Related
Oct 9, 2012
I have a desktop connected to internet broadband provider by a ADSL router with one extra connection to a landline phone.I have a samsung stv LA46D550 with lan port. i woulike to connect TV to the internet provide so that I can browse in TV.what extra hardware and cables do I require(with specifications).also a diagram how to connect these
my desktop has windows 7
TV LCD TV
of coursse I have connected TV to my desktop through an HDMI connector and can use TV screen as either a CLONE monitor to desktoop lor additional monitor to desktop.is this enoiugh or should I connect broadband ADSL router to TV through a router.I prefere wired connections rather wireless.
View 7 Replies
View Related
Apr 15, 2011
How the password is correct, the firmware is updated, it finds the home network but when I press connect it tries a few seconds then says unsuccessful
the unit itself is Pandigital Novel 7"
the router is a Dynex Wireless router with : WPA/WPA2Personel(PSK)
Encryption is : TKIP +AES
802.11e QoS is on
Wireless mode is both g and b
Wifi protection has been both on and off trying to connect
SSID is correct and broadcasting.
We got the thing so her ha;f blind mom can play a few games, but I need to connect to download then, either that or know how to download them to the computer then transfer them to the Pandigital?
View 8 Replies
View Related
Dec 14, 2012
I have 6 computers connected in LAN network. In one of the machines(client_1) i have installed the VMWARE.VMWare and Clinet_1 are talking to each other whereas VMWare and other clients are not getting connected. I tried various solutions from the internet but all in vain...i would like to have vmware as another machine in my LAN with incoming and outgoing connections to access files.
View 9 Replies
View Related
Nov 27, 2011
I just installed my new TV by Samsung UA55D6400. it's great. I understand that it can be connected to local home net. it has Wireless LAN Built-in BU no Wireless LAN Adapter Support. What I have to buy and install in order to connect it to the local net and also stream movies to it?
View 3 Replies
View Related
Jan 7, 2012
I have a cable wireless router in the ground floor lounge and have set up a home wireless network. In the upstairs study we have two desktop computers connected to the router via the wireless network. I have a laptop computer used around the house and garden which also uses the wireless network.A laser printer and an inkjet printer are both connected to one of the computers in the study via USB and are shared with all computers.This means that the computer with the printers connected must by running if anyone requires prints. Both printers have USB and Ethernet ports – but running a network cable to the router downstairs is impractical.Is there a way of connecting the printers directly to the network and leave them powered up so they can be used by any of the computers. I am hoping that there is some extra hardware that will enable me to do this perhaps via wireless.Or – would it be possible to use mains Powerline Network adaptors – with one adapter connected by Ethernet cable to the router and other adaptors connected by cable to each printer.
View 4 Replies
View Related
Jul 20, 2011
My Linksys Wireless-N Home Router, having a model no: WRT120N keeps disconnecting and connecting.. what is the best thing I could do to eliminate that?
View 5 Replies
View Related
Feb 18, 2012
I'm in university halls, using the university wireless network. The network seems to be a large number of routers all with the same SSID on the same network.Usually my connection is great; but sometimes my computer decides to switch to the router from another flat. A few minutes ago my wireless config utility told me I was connected to the flat 24 router. I am now connection to the flat 26 router. It wouldn't be much of a problem, only it's give or take, around 140 times slower because of how far away it is. Heres a quick comparison of the speeds:ad Connection: (The ping here is very mis-leading, it took several minutes to calculate the ping and several more minutes simply to start the download whereas on the previous test it was instant)Here is one I took in December which shows how bad the ping can get:How do I tell my computer to ignore those other routers with the same SSID? They have different MAC addresses, is there something I can do with that? Windows can't tell the difference, I have to do it through the driver software that came with my Edimax wireless card, it recognises each router seperately but ultimately it always recognises it primarily by it's SSID. Sometimes it sticks to the good one, sometimes it changes every few minutes and I have to manually change it back and it is very frustrating, can't it just ignore the bad connection completely?
I can't login to change any of the router settings and the router doesn't have any ethernet ports for students to use, so I need a solution from the PC end (If I could i'd simply change the SSID to something slightly different so it didn't clash, then there would be no problem). The router is literally right outside my door, but my computer insists on switching to the one 50 metres away instead
View 2 Replies
View Related
Feb 8, 2011
What I learned was it was bad to connect directly to the modem because you are left open to the internet. Currently my friend just got the internet and I told them to buy a router but they did not, and just have it directly connected to the modem. Is this fine, because they only have one computer, and it works fine for now, but wouldn't this be prone for attack?
View 3 Replies
View Related
Apr 12, 2012
I have a home network. There are a total of 3 PCs. Each runs Server 2008 32 bit. One PC - Lets say Server A has 2 NICs with Ip addresses, 10.0.0.10/30, 10.0.0.2/30.Other two computers Server B and Server C have single NIC with addresses 10.0.0.1/30 and 10.0.0.9/30 resp. So as you can see that there are two subnets 10.0.0.2 - 1 and 10.0.0.9 - 10. I can ping B and C from A. I want that B and C can also ping each other and if I run tracert on B or C, it should give me the route to the destination via A. All this without any other hardware. Like using route add... etc eg. if I write tracert 10.0.0.9 on B, it should return a route like 10.0.0.1-----10.0.0.10------10.0.0.9. Refer to the image that I have Attached
View 7 Replies
View Related
Jul 16, 2012
Unlike most DVR's, this particular model has a 4-Channel RJ-45 input (others normally have analog BNC video inputs) this is achieved since the cameras come with video baluns which make use of ethernet (RJ-45) wire.can I have such a set-up without using a DVR, instead I would channel 4 cameras to a wireless router with 4 RJ-45 inputs? From there maybe I could connect it to the internet for remote viewing or to a home network for better streaming / saving video recorded into hard disk?
View 6 Replies
View Related
Oct 29, 2011
I'm having issues connecting a HP 9000dn printer to my home network. I have windows 7 x64 with a Belkin wireless router. I have the printer (via a jetdriect 615n driver) connected to my router and the computer will not see the printer. I'm a newbie to networking
View 3 Replies
View Related
Feb 7, 2012
I have a computer that was previously connected on-site (hard wired) to a corporate network. I am now attempting to connect it on-site to my home network. While I have a live Internet connection going into the computer, I cannot connect to the Internet. Is there soem sort of setting adjustment that i need to make?
View 5 Replies
View Related
Apr 9, 2013
I split my network into 2 to make it more accessible during peak time and to minimize internet traffic. However by doing this only the first network can access our Network Access Storage, the other network can access it because the two are separated by different router and switch also the supervisor need to see both network at the same time for monitoring purposes..
View 6 Replies
View Related
