Connecting Linksys E1000 To Comcast Router?
May 2, 2012
I have a Comcast Router pushing out IP's in the 10.1.10.X range. I want to hookup a Linksys E1000 Router so I can use its wireless & Guest access features. The Linksys is using the 192.168.1.x range. I have a cable from the comcast router running into the Internet port of the Linksys. I have tried changing the Linksys router IP to 10.1.10.x and turning off DHCP. It will not allow me to the internet nor allow the PC connected to it to connect to the PC that is attached to the Comcast Router. I cannot replace the Comcast as it is a combi router/modem.
View 2 Replies
ADVERTISEMENT
Feb 16, 2011
i need to connect a linksys e1000 to an existing dlink router. i have tried several solutions that i have found on the internet, but none have worked. i need DETAILED instruction tailored to e1000 specifically because i am having trouble with dhcp definitions as i have not done this in years. i can get it to work, but i have to maintain security and everything i have done still allows me through to dlink router.
View 6 Replies
View Related
Aug 23, 2011
why I am only able to connect at 39Mbps (often 5.5Mbps) to my Linksys E1000 Router? Residential. Wood Frame/Stick home construction. No other devices connected to router. <10 feet from E1000 Router. Line of sight (nothing in between router/laptop). New Dell Inspiron DW 1501 Wireless-N WLAN Half-Mini Card.
E1000 Network Mode: Mixed
Channel Width: Auto (20MHz or 40MHz)
Firmware: 2.0.01 build 08
At times I have seen it flash to 52Mbps but immediately drops to 39Mbps or lower (26, 5.5, etc.).Sales prop indicates up to 300Mbps. Where is the other 90% of the connection speed they’re talking about? OR is 39Mbps expected?
View 1 Replies
View Related
Dec 27, 2011
I'm trying to connect my Nook Tablet to my wireless E-1000 router. I'm using a cable connnection for internet service. THe nook will find the network indicating "excellent" signal , but when it goes to authenticate it disconnects. After reading about WEP security, I switchedecurity setting of the Cisco router to "WPA Personal". Results are the same.
View 1 Replies
View Related
Jan 24, 2013
I have a 2wire wireless router and I would like to connect the e1000 in another room as a AP(access point).
View 2 Replies
View Related
Mar 30, 2012
Is it possible to connect my Cisco E1000 to a Linksys Wireless G Router?
View 8 Replies
View Related
Jan 24, 2013
I have a Linksys E1000 router just upgrade to the latest 2.1.0.2 firmware...I have a PPPoE connection which used to run smoothly on the router..however off late...suddenly the router stopped connecting..it always shows "connecting" in the status tab of the router page...and eventually says failed to obtain IP address...however when I attach the cable directly into my PC it works just fine.I also had a word with my internet provider...he's kept the MAC open (or something like that) so he said that isn't the issue and he keeps saying there must be some issue with the router. However, occasionally the router DOES connect for half hour or so and then just refuses to connect again !..
View 2 Replies
View Related
Feb 8, 2012
I've got an issue with my router. The Linksys E1000.In my opinion it supports the Wireless-N mode, so does my wireless lan card which is the Atheros AR5B93 (also known as the Acer Nplify 802.11 b/g/n). When I connect to the router, it only connects in normal wireles mode, so no b,g or n mode. But when I look at the Client Tabel of the router all other devices connected to the router are in Wireless-G mode. Even my laptop doesn't connect in Wireless-G mode.I want to have my laptop connected in Wireless-N mode. What do I have to do, to make this working?
View 7 Replies
View Related
Aug 3, 2011
I'm trying to connect my Cisco lab to the internet. I've configured my 2611 to accept DHCP. I can ping the Linksys E1000 router but can't ping the modem on the other side, and cannot get out to the internet with the PC that's connected to the lab. When I look at the DHCP table in the E1000 the 2611 shows up in the table. I can ping all other computers on the lan, just not the modem to get out to the net.I have the configuration for the 2611. Did I miss something. Is the modem blocking ICMP traffic?
Router#sh run
Building configuration...
Current configuration : 931 bytes
!
version 12.3
service timestamps debug datetime msec
[code].....
View 3 Replies
View Related
Jul 26, 2010
I have tried to connect Comcast to my new E2000 router, with negative results. I did perform the firmware upgrade on the router (to 1.001). My old Netgear WiFi router works fine, so I know the configuration works.For testing purposes I have the following:
MacBook Pro > E2000
Comcast > E2000
Both via Ethernet cable.
I do have access to the E2000 via web based interface. I have tried a variety of configurations, including the use of the "static" configuration using the current Comcast ip, gateway, subnet and DNS that currently exists. I am unable to get the Auto DHCP to work - Comcast ip's do not appear (in the "status" window.)
View 9 Replies
View Related
Sep 21, 2012
I bought this wonderful voice gateway off the internet from someone. So not sure if they ever used it with Comcast.So far I hatve had no internet once I plug it to the cable. I have asked Comcast tech for activating this device. However they say it is not supported and they have tried sending it the Activation signal but they say it fails. I can see all lights lit up and go green when I connect this device to the cable, is there a firmware upgrade for DPQ3925 ?
View 2 Replies
View Related
Oct 16, 2009
My router worked fine. Comcast did updates and now it wont work. If I connect the cable modem to the laptop the internet works fine.It's the router. She said I need to reconfigure it. I tried looking on the site, typing in the 192.168.1.1 thing and the password "admin" is not correct.
My cable modem is Motorola SB5120. My linksys is WRT54G2 V1. how to reconfigure this to work! We work from home and this is a huge obstacle for us to not have wireless internet
View 9 Replies
View Related
Jan 24, 2012
I have a problem with my E3200 that has happened at least 4 times since I first purchased, installed and configured it. Initially I thought it might be something with Comcast, but a) I never had the problem with my Linksys WRT54G router and b) It seems I can now duplicate the issue by saving a config file and restoring it.The specific issue appears to be somewhat random. At some point the connection to the Internet simply stops for no apparent reason. I am able to ping the router and connect to it. I am also able to drop and renew connections to the cable modem successfully. Furthermore, I can ping my network side of the router, as well as the external address handed to my router by the cable modem, and the cable modem gateway address, but still no connection to the Internet.The only solution to my problem has been to restore the factory defaults to the router and reconfigure it from scratch, which does seem to fix the issue for a time until it occurs again. FYI, I do not use the Cisco connect software because I have several custom port and QOS configs that are necessary for an IP Phone and other hardware on my network.
View 1 Replies
View Related
Jan 12, 2010
I have a need to have 2 seperate networks from my comcast cable modem.I was hoping to plug a 5 port hub into the cable modem and then plug both the wrt610n and the wrt54g into the hub. Seem that only one of the routers will get an ip assigned from Comcast.Is there a way to have one ISP cable modem and create two different home networks with the two linksys routers, thus two separate independent networks?
-Network 1: public household use and family (Jane's wireless laptop, household PC's etc).
-Network 2: private household/company use and separate from the public family network (company wireless laptop/company PC, un-secure media server).
View 7 Replies
View Related
Apr 18, 2012
I just recently purchased comcast internet today and self installation kit that came with the modem and all..... got it all set up no problems activated did speed test directly from cable modem to laptop computer wired and was getting 10mbps down and 3mbps up well went out and bought a linksys e900 wireless router.... connected it no problems... however my laptop wireless and phones connected to the router with speedtest is only getting 300kbps down average!!! but the upload is still 3mbps.
View 9 Replies
View Related
Jul 23, 2011
I am setting up a e4200 wireless router on a Comcast business account that uses a gateway (SMC8014).I have fixed public IP [x.x.x.x/30] and the gateway sets up a subnet 10.1.10.0 (255.255.255.0). I have mail server and DNS server at 10.1.10.20 and I use port forwarding in the SMC gateway.
The setup of the e4200 using the software sets up a network (192.168.1.1). I can connect devices to the router and browse the external Internet. However, when my android phone connects to the e4200 it gets an IP such as 192.168.1.101. However, I cannot download my mail which is at 10.1.10.20. When I try to browse that IP from the android phone I get the SMC gateway at 10.1.10.1 and not the computer at 10.1.10.20. If was coming in from the external Internet port forwarding would take over but it does not work for the android phone connected to the e4200.
Also, i noticed that when I set up the default setup for the e4200 the "Cisco Connect" says the WAN address is 10.1.10.155 and the LAN address is 192.168.1.1. However, when I go to the SMC Gateway and list the connected computers it doesn't see the e4200 at 10.1.10.155. If I set up the e4200 within 10.1.10.0 then the SMC sees it (but the computer name always says "unknown"). It I set the DHCP in either the SMC or the e4200 within the 10.1.10.0 subnet I can see the phone connection in the SMC when I list the connections but any requests to 10,1,10.0 computers goes to the SMC gateway.
View 5 Replies
View Related
Apr 25, 2013
Currently have a linksys wrt54gs connected to an Arris TG852G/CT. Currently getting poor speed via WIFI for Comcast Xfinity service. The Arris modem is connected directly to the Linksys Wireless Broadband Router via Ethernet. It lists the linksys broadband router as unknown device and does need utilize the 54 mb/s g standard available on this device. I have updated the firmware to 1.52, reseted the Arris gateway to factory defaults, and reset the linksys to factory defaults as well. The IP address is 192.168.1.1 for the linksys/ 10.0.0.1 for the Arris gateway.How do I improve connectivity between the Arris Gateway and the LinkSys broadband router (model WRT54GS ver 6.0)
View 8 Replies
View Related
Jan 5, 2011
Hard wired network (15 workstations.) I had a dsl modem connected to my network switch and linksys wrt54gs router connected to that modem. All hard wired workstations had internet access AND there was a wireless internet connection. With any wifi device I could access the internet.I switched from dsl to comcast. All hard wired work stations still have internet. but when I plug my wireless router into the modem (comcast business IP gateway) there is no wireless internet connection. The hard wired workstations can still get online and there IS a wireless network, but it does not allow internet access (page cannot be found etc.)
Comcast says it absolutely should work. Linksys says it requires simple reconfig of router settings (reset router, clone mac address.) I have read knowledge base articles from linksys and followed each step. The lan ports of the modem are all working if I connect to them directly with a laptop and cable. I have reset router multiple times, cloned mac address, dhcp release/renew.
My physical connections are correct. In the router set up utility, I can see the mac adrdress and ip address but can't tell if the IP is from the modem or the router. Default gateway is always 192.168.1.1 in the router AND in any workstation ipconfig screen. Ip addresses are 192.168.1.xx in ipconfig at any workstation AND in the router set up status.
I cannot access internet via router even if plugged directly into it. It is as if the router is not getting the correct information from the modem. However, it worked perfectly with the DSL modem the day before we changed.My workstations are all hard wired and work. I simply want to have Wi-Fi also... for phones and laptops w wireless etc.
View 8 Replies
View Related
Nov 8, 2011
I am swapping my AT&T DSL and Comcast cable for U-verse. In the basement, I have a Netopia DSL modem connected to a Linksys BEFRS81 v. 3 ethernet Cable/DSL router/8-port switch. Cat 5 cables are attached to the router, then run throughout the house so we are "networked" to the DSL modem and use a patch cord from laptop or desktop into the wall to get to the Internet.
View 1 Replies
View Related
Feb 7, 2013
Comcast installed a new fiber 10M EDI internet connection in our facility the other day and found out it is our responsibility to provide a layer 3 gateway to map the internet connection to the 14 public IP addresses they assigned to us. We are using RV042 for our existing networks with a T1 we had.
Will the RV042 provide the gateway function to route the single IP address comcast provided to the 15 public IP addresses? If so , can you provide the configuration example on this process?
Comcast EDI Connection ---> ???????? ----> 14 Static External Addresses
Interconnect Block 51.235.227.60 / 255.255.255.252.Comcast Gateway is 51.235.227.61Clear Layer 3 device WAN interface: 51.235.227.62Usable IP Block 51.235.227.96/28Mask: 255.255.255.240Usable Addresses: 51.235.227.97 - 51.235.227.110
View 1 Replies
View Related
Aug 9, 2011
Comcast had us unplug our modem in order to upgrade to their new faster speed. now our wireless router won't work. We've reset the router twice. we can set up the wireless network but we cannot connect to it. The connection last for about 5 minutes and then we get an error, cannot read IP address. Comcast says it is not their problem and linksys says they can't assist either.
View 1 Replies
View Related
Feb 28, 2012
I was able to install the RV042 router to my ATT DSL line (WAN1 port-INTERNET) and it gets an external IP address automatically and the Internet works. When I connect my Comcast Internet to WAN2 port INTERNTE/DMZ) it doesn't get an IP address. and the Internet goes down and the WAN2 port ip address says 0.0.0.0.I've tried releasing/ renewing and it still says 0.0.0.0.Everything else is set as the default.
View 1 Replies
View Related
May 15, 2011
I had to do a total recovery on my Toshiba laptop after getting a bad virus. Now I can't get my router to recognize itHow can I reinstall it? I've worked on this computer for several days trying to get rid of the virus (windows recovery) and it was so bad that's when I decided to just do a recovery on it, and I am worn out and would love to be able to just get this last thing fixed
View 10 Replies
View Related
Dec 8, 2011
A friend of a friend has a business with 8 computers (3 lap tops) and then desktops. He uses Verizon. I have no idea about how to set this up correctly but, would like to try.He got 2 Linksys routers and asked if I could get them to work on his network. I said I'd try.
There are NO INSTRUCTIONS -
do they go to the "boss computer" and then? I just don't know and feel too stupid to say I'm not sure.It's probably very easy but, it's been years since I've worked on Networks.
View 7 Replies
View Related
Nov 6, 2012
I'm trying to setup my linksys e1000 router as an access point and I cant figure out how to log in to it to change its settings. I've done every reset procedure I can think of but when I power it up it still shows up as a "security enables network".
View 5 Replies
View Related
Jun 10, 2011
My modem CAN connect to the Internet but my router CANNOT. I've called my ISP (Brighthouse) and went through a whole process of bypassing the router, restarting the modem for 2 minutes, and restarting the router for 30 seconds. Then I even got assistance from the router's maker (Linksys) by switching the IP address of the router, they said this could be the issue if my modem had the same IP address. I switched it to 192.168.2.1, but still no luck. I do not know what to do now. The new router is a Linksys E1000. I haven't got the specs of my modem yet.
View 3 Replies
View Related
Mar 26, 2012
I own a E1000 router that I use with several wireless machines. Unfortunately, I cannot connect to the configuration of the router by typing url...in a browser, be it wireless or weirdly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router". I tried to switch my router off and on, but that doesn't work. Totally resetting the router solves the problem, but not definitely.Is there a solution that does not require resetting my router?
View 2 Replies
View Related
Dec 20, 2011
My guest can't use my wireless network and I can not add more devices like a ipad2. Got a new ipad2 for my son for Christmas been trying to set it up for Christmas, so on Christmas day I am not trying to do the set up. My problem is I can not get it to log on to the network. I have been putting in the same pass word all my other computers in the house use but it will not work...
View 2 Replies
View Related
Feb 10, 2013
My wireless router (E1000) was accidentally unplugged. Since then the wireless LED light doesnt come on and the router cannot be detected. All the other lights are on. I tried to reset it but I dont think it worked, since the power LED didnt blink as its supposed to do after holding reset for 10-15 seconds (or more!!).
View 5 Replies
View Related
Aug 9, 2011
I've been using the E1000 for months. I have 2 iphones, an ipod, a windows 7 netbook and a macbook connected wirelessly to it. It's been set at wpa2/wpa mixed mode all this time without a problem. Out of the blue: no wireless connection on any device. I restarted the modem, router, PC's, phones, etc. I've updated the firmware. The only way I can get a wireless connection is to use wep. How can I get the better security and speed of wpa2 back?
View 4 Replies
View Related
Feb 21, 2012
I am trying to access the internet with my ipod and it is picking up my wireless connection but it is asking for a password, how do I get my password. I don't remember seeing a password when I hooked up my router several months ago. I called Cisco for some technical support but they wanted money to get me and I am not paying them a dime.
View 1 Replies
View Related
Jul 3, 2012
I can setup my router with the cd
View 1 Replies
View Related
Jul 26, 2010
I have a PS3, and i play allot of video games such as all COD game especially MW2. It says i have a strict or moderate NAT. My router is in the same room as the PS3, so i should have a Open Nat.Also i have another question, i bought this Epson printer from Best Buy, i was wondering if I can connect to it Wireless, but i think i cant connect to it wireless cause i dont see the WiFi Certification on the printer or anything hints that it can connect wireless
View 9 Replies
View Related
