Setting Up 2 Linksys E1000 Router(s)?
Dec 8, 2011
A friend of a friend has a business with 8 computers (3 lap tops) and then desktops. He uses Verizon. I have no idea about how to set this up correctly but, would like to try.He got 2 Linksys routers and asked if I could get them to work on his network. I said I'd try.
There are NO INSTRUCTIONS -
do they go to the "boss computer" and then? I just don't know and feel too stupid to say I'm not sure.It's probably very easy but, it's been years since I've worked on Networks.
View 7 Replies
ADVERTISEMENT
Feb 15, 2013
I am a powerbook G4 user, Mac's wireless is good so far.OSX 10.4.11 and when I am using E1000 extender, often the admin page shows up automatically like 192.168.1.1 and asks me to log in and once I log into the admin page, of corse show up the admin page.So, all my other internet pages are gone every time.Only shows the admin page.It does not happen with windows PCs.
View 1 Replies
View Related
Apr 25, 2011
Does the E1000 router come with a default security setting upon installation using the supplied CD?
View 9 Replies
View Related
May 15, 2011
I had to do a total recovery on my Toshiba laptop after getting a bad virus. Now I can't get my router to recognize itHow can I reinstall it? I've worked on this computer for several days trying to get rid of the virus (windows recovery) and it was so bad that's when I decided to just do a recovery on it, and I am worn out and would love to be able to just get this last thing fixed
View 10 Replies
View Related
Nov 6, 2012
I'm trying to setup my linksys e1000 router as an access point and I cant figure out how to log in to it to change its settings. I've done every reset procedure I can think of but when I power it up it still shows up as a "security enables network".
View 5 Replies
View Related
Jun 10, 2011
My modem CAN connect to the Internet but my router CANNOT. I've called my ISP (Brighthouse) and went through a whole process of bypassing the router, restarting the modem for 2 minutes, and restarting the router for 30 seconds. Then I even got assistance from the router's maker (Linksys) by switching the IP address of the router, they said this could be the issue if my modem had the same IP address. I switched it to 192.168.2.1, but still no luck. I do not know what to do now. The new router is a Linksys E1000. I haven't got the specs of my modem yet.
View 3 Replies
View Related
May 2, 2012
I have a Comcast Router pushing out IP's in the 10.1.10.X range. I want to hookup a Linksys E1000 Router so I can use its wireless & Guest access features. The Linksys is using the 192.168.1.x range. I have a cable from the comcast router running into the Internet port of the Linksys. I have tried changing the Linksys router IP to 10.1.10.x and turning off DHCP. It will not allow me to the internet nor allow the PC connected to it to connect to the PC that is attached to the Comcast Router. I cannot replace the Comcast as it is a combi router/modem.
View 2 Replies
View Related
Mar 26, 2012
I own a E1000 router that I use with several wireless machines. Unfortunately, I cannot connect to the configuration of the router by typing url...in a browser, be it wireless or weirdly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router". I tried to switch my router off and on, but that doesn't work. Totally resetting the router solves the problem, but not definitely.Is there a solution that does not require resetting my router?
View 2 Replies
View Related
Dec 20, 2011
My guest can't use my wireless network and I can not add more devices like a ipad2. Got a new ipad2 for my son for Christmas been trying to set it up for Christmas, so on Christmas day I am not trying to do the set up. My problem is I can not get it to log on to the network. I have been putting in the same pass word all my other computers in the house use but it will not work...
View 2 Replies
View Related
Feb 10, 2013
My wireless router (E1000) was accidentally unplugged. Since then the wireless LED light doesnt come on and the router cannot be detected. All the other lights are on. I tried to reset it but I dont think it worked, since the power LED didnt blink as its supposed to do after holding reset for 10-15 seconds (or more!!).
View 5 Replies
View Related
Aug 9, 2011
I've been using the E1000 for months. I have 2 iphones, an ipod, a windows 7 netbook and a macbook connected wirelessly to it. It's been set at wpa2/wpa mixed mode all this time without a problem. Out of the blue: no wireless connection on any device. I restarted the modem, router, PC's, phones, etc. I've updated the firmware. The only way I can get a wireless connection is to use wep. How can I get the better security and speed of wpa2 back?
View 4 Replies
View Related
Feb 21, 2012
I am trying to access the internet with my ipod and it is picking up my wireless connection but it is asking for a password, how do I get my password. I don't remember seeing a password when I hooked up my router several months ago. I called Cisco for some technical support but they wanted money to get me and I am not paying them a dime.
View 1 Replies
View Related
Jul 3, 2012
I can setup my router with the cd
View 1 Replies
View Related
Jul 26, 2010
I have a PS3, and i play allot of video games such as all COD game especially MW2. It says i have a strict or moderate NAT. My router is in the same room as the PS3, so i should have a Open Nat.Also i have another question, i bought this Epson printer from Best Buy, i was wondering if I can connect to it Wireless, but i think i cant connect to it wireless cause i dont see the WiFi Certification on the printer or anything hints that it can connect wireless
View 9 Replies
View Related
Sep 3, 2011
With the E1000 tthe wireless devices they seem to work just fine, I can access the internet just fine.
For my desktop PC in oder to use the router to get on the internet or to even use the Cisco Connect to check the router, the E1000 needs to be rebooted. I am unable to access the router otherwise. I have tried 3 different LAN cards all with the same results.
The latest firmware notes do not look like upgrading the firmware will work. My Router info from Cisco connect
Model name: Linksys E1000
Model number: E1000
Serial number: CVN21L422937
Firmware version: 2.1.01 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): unknown
View 1 Replies
View Related
Jan 24, 2013
Things seem to slow down significantly to the point of loosing connectiviety. When I check, my mips are 150 or so. Tried disconnecting and connecting again but didn't work. When I power down the router and power it up, I get 300 mps again but doesn't last too long
View 2 Replies
View Related
Dec 30, 2011
A lady gave me E1000 along with an IMB Thinkpad because her husband was the main user on the internet. I have an intel iMac 10.4.11, DSL. I have not yet connected to either device via the router. I am new to wireless routers. I have been to the configuration page
View 2 Replies
View Related
Apr 7, 2013
I have a Linksys E1000 router which was working fine. My hard drive crashed; I replaced the hard drive and now my router is not recognized. I have reset it and tried to reinstall it with the CD. Nothing works.
View 1 Replies
View Related
Jun 23, 2011
I had an E1000 for a couple of years that worked OK. Then it went nuts--sporadically dropped the signal, wouldn't show its web page, etc.--maybe a power surge, who knows? So I tossed it and got a new one on the theory that it would be a plug in replacement .The new unit had a good signal, but also wouldn't show its web page, so I couldn't configure security. I removed Network Magic and everything else I could see pertaining to the old unit. However, the CD for the new unit still gives me: " Your router has already been set up. You need to use an Easy Setup Key that you can use to get other computers connected." Needless to say, I don't have such a thing. Cisco Connect is not installed at this point, so I can't go into it to create one.How can I purge the remains of the old unit so the new one will install properly?
View 6 Replies
View Related
Jul 14, 2011
I have E4200 connected to Internet. It is configured with NAT. My side of the router is set to 10.10.10.0 and DFG is set to 10.10.10.254. Server is connected at 10.10.10.1 and is DHCP host.I now have E1000 that I want to connect downstream side of the E4200 (located on the other side of the building). I want the E1000 to be an extension of the existing network so the whole building looks like one network. I'm not sure how to configure the E1000. I assume I need to disable NAT but I'm not sure how to configure the Internet IP addresses of the router and nro am I sure how to configure the local network side of the router.As I write this, I wonder if I connect one of the Ethernet ports of the E1000 to the E4200 and just leave the Internet side unplugged?
View 2 Replies
View Related
Jun 10, 2010
I'm trying to set up my E1000 router and when I run the Cisco Connect software that came with the router I get a message that says that it can't find the router, I've tried running it with my computer connected to the router and not connected. I've looked through the FAQ section and didn't really find anything. I'm trying to set it up on a laptop, it's a Vaio running Windows 7, I don't if that makes any difference.
View 7 Replies
View Related
Nov 12, 2011
I am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 2 Replies
View Related
Feb 16, 2011
I've been searching off and on for the past couple months trying to figure out what we could do to our router to open our NAT, after having both the PS3 and Xbox 360 tell me I've got moderate NAT. I tried a DMZ with my PS3 having a static IP, I tried UPnP. I messed with firewall settings, to no avail.
I recently found something that did work however, on Google. Basically what happened was, I needed to reset the router and change a few settings on top of enabling UPnP I didn't know about(CTS Protection, remote management) how they could have anything to do with translation of data.
But like I said, after doing a huge step by step walk through, I was able to get open NAT in the network tests of both PS3 and 360(even though the PS3 obviously still says Type 2. It used to say Type 2, but it also used to have an error code at the bottom of the page). I've checked in games on each console, and they tell me I've got open NAT.
Now I still have one tiny problem. Red Dead Redemption. I play Red Dead Redemption online with two friends(who, incidentally, have the same router as me), and we haven't been able to communicate if we were using routers. We still can't, but I'm thinking that it's not my router anymore. I'm thinking his router has incorrect settings. Am I correct?
View 8 Replies
View Related
Dec 28, 2012
I have two mac laptops and am trying to copy a directory with a number of PDFs in it. The files aren't particularly large, but there are many of them. At some point in the process the router stops and must be turned off and on before it will respond again either wirelessly or wired. I have tried the same experiment with both devices wired and the router works fine. I have tried changing the MTU, channel, beacon setting, etc. as other forum posts have tried. I tried reflashing the firmware, resetting to factory defaults and reconfiguring. So far no success. Cisco support wants me to return the router. Frankly I'm at the point of considering the former Linksys/Cisco products complete rubbish. I am going to have to buy a new router even if I return this one since I can't be without a router for any length of time.
View 8 Replies
View Related
Mar 5, 2013
The router had firmware 2.0.x(?) and I tried to update to the latest FW, according to the webpage that's
FW_E1000_2.1.02.006_US_20130115.bin
Hardware is E1000 v2 according to sticker on back.The firmware update failed (no reason given) and the router now hangs in limbo where all it does is flashing the power LED.I set my PC to 19?2.168.1.2 and TFTP'd the firmware over to 192.168.1.1 - no errors reported and 192.168.1.1 is pingable. Held reset for 30s, then powered down the router for another 30s. On power-up the router still flashes the power LED.
View 3 Replies
View Related
Jun 26, 2012
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
View 4 Replies
View Related
Jun 20, 2010
I just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies
View Related
Aug 17, 2011
I have a linksys e1000 modem router as the wireless internet connection in my home, now I bought a new one linksys e1000 to use it as an access point to cover the uncovered area, How can I do that?
View 1 Replies
View Related
Sep 21, 2011
So here is the issue:
When I connect my modem directly to my computer (modem > computer) it works just fine, internet connects and everything through the direct ethernet connection.But when I connect the modem to the router and then try to connect wireless with any other computer (modem > router > wireless) nothing works. Not even when I have it connected directly from the router to the ethernet on the main computer. (Which has ALWAYS worked until now.
View 1 Replies
View Related
Feb 16, 2011
i need to connect a linksys e1000 to an existing dlink router. i have tried several solutions that i have found on the internet, but none have worked. i need DETAILED instruction tailored to e1000 specifically because i am having trouble with dhcp definitions as i have not done this in years. i can get it to work, but i have to maintain security and everything i have done still allows me through to dlink router.
View 6 Replies
View Related
Jun 30, 2011
my brand new Linksys E1000 wireless router. I am really struggling and cannot figure out what I am doing wrong.
I live in The Netherlands, have a modem (DSL I think...) and can connect wired through the modem with no problems.
I installed the E1000 with the CD, followed all the steps and my laptop is finding the network. However, it's only local, no internet and I don't understand why. Have tried to connect (wired) my computer to the E1000 and the E1000 to the modem but that doesn't work either.
View 2 Replies
View Related
Jan 28, 2012
However, my 13" Macbook (running Lion) sometimes finds if hard to connect after I turn it on. I will have to continously turn off and on the wifi of the macbook to have it force to look at wifi networks. It will not be able to see also other wifi networks which are present in my neighbors which my windows 7 and other machines can see. After playing around with it I found that the macbook will connect to wifi only after I connect it momentarily via cable. I do this everytime I turn on my macbook.I just upgraded to a Macbook Pro running on Lion and the same thing happened. I tried the same solution of connecting first via cable but to my disappointment, would not see any wifi network including my neighbor's which again the other machines can see. So I am stuck with using cable for now.
View 5 Replies
View Related
Jul 29, 2011
is there a way i can block a website from being viewed.i would like to do this from the setup page of my e1000 under website restrictions.
View 1 Replies
View Related
