Cisco WAN :: 2611 / D-Link 321 - PPPOE Dial Up Link Dead
Mar 6, 2012
I'm in an issue w/ on of our ISPs. We're using an ADSL line as a secondary light load line ( 16 MBit, /w PBR in place to separate the 80 and 443 from the business-critical applications running via a SDSL link. ).
I am on a 2611 XM with IOS 12.2, mated to a D-Link 321B modem running in transparent mode. After running smoothly for weeks, for a few days now, every night some time between 2 AM and 4 AM the link would die with the dialer showing:
Virtual-Access1 is up, line protocol is down Hardware is Virtual Access interface [code]....
To my knowledge, the only option to bring it up again is to reload the box . Taking into account that the router is our DHCP server and the date gets reset to 1994, interesting effects are the outcome of resetting the box.
Well, the ISP have checked their gear and keep saying that these report a "port error" ( quite unspecific ) and blame me that I have a wrong. config in place - which is here:
interface Dialer2
description ecotel Bridge
ip address negotiated
no ip proxy-arp
[code]...
Just for no reason that I know of the wireless stopped working. I can can connect to the SSID fine and there seems to be good signal strength, but no wireless internet access.
I have up to date February 15, 2011 firmware, 205NA, hardware version = B1.I have done a reset with no luck.I have done a 30/30/30 factory reset = no luck
So let me start by saying that i'm stupid, as i did not 1st read the manual properly and thus upgraded my camera WIRELESS.. (when manual clearly states by cable ONLY).
Camera is now DEAD. Only red led light is flashing.
Hardreboot not working (pushing reset, then switching on camera & hold reset for 30 secs)
Is there anything else that i can do myself or is this gonna be a repair job?
I just recently bought this router (DIR-615 rev E3) to act as a Access Point for the dead wifi spot in my room downstairs. I set up everything properly (Turned off DCHP, set ports and gateway..subnet blah blah) and it was working fine. My wireless speeds were perfect, and had no issues with that. However, my wired speed was significantly slowed down. I have Verizon Fios and have the wire from that plugged in to LAN port 1 on my DIR-615. I have another wire going from Port 2 to the back of my PC. My normal speeds are about 30mbps down and 25mbps up. When I connect my internet through the second router (DIR-615) I get a maximum of about 3.0mbps up and down, doesn't go much higher than that. The wireless however, gives me about 11mbps both ways, which is fine.
I thought it might have been a firmware issue so I flashed to DD-WRT (build 15778), but the problem persists. I've tried most everything and am getting desperate. There's absolutely no logical reasoning for the slowdown. I have confirmed it's a router issue because I also turned off wireless on my laptop and plugged that directly into the router instead of my desktop and get the same 3mbps.
My daughter is on an Army Base in the South Pacific. They have Dial up internet on their home telephone not DSL. They have high speed wireless at the base community center/coffee shop. I will be going there in 9 days to install the dir-615. She has a Dell Desktop with Vista Basic SP1, laptop with XP, IPAD2 and a NOOK Tablet. The dir-615 HVE1 with firmware 5.00na on the bottom sticker. She said she was able to go to web address, login, change the user name and password, started on the wireless configuration and she paniced. My question is basically this. by using a cat5 cable from the desktop to the dir-615 with dialup internet connected can the router be setup using the automatic method as opposed to manual. Our first priority is to be able transfer files to the 2 tablets without being connected to the internet like a switch and secondly If possible go on to the internet from a Tablet or the Laptop. I assume the second option would reuire internet sharing option when setting up the network and performance would be ugly.
Can get I get this router to work this way with just dialup to set it up
I just got a dir-655 revb, and it does not connect to the internet. I have DSL, and the old router works fine with PPPoE, when I configure my dir-655b router, it can not connect to the internet. I get the flowing error:
info Mar 23 22:31:11 rp_pppoe =' read pppoe_conn_session error or first time dial notice Mar 23 22:31:10 pppd 2.4.3 started by root, uid 0 info Mar 23 22:31:10 RP-PPPoE plugin inform wantimer to reset auth, discovery variable info Mar 23 22:31:10 RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3 info Mar 23 22:31:10 Plugin /lib/pppd/2.4.3/rp-pppoe.so loaded. info Mar 23 22:31:05 Exit.
I'm trying to find out what platforms support Multilink PPP with Link Fragmentation and Interleaving over a single link, when that single link is PPPoE. In searching the documentation, the best information I can find is that it seems to be supported in one direction on the ASR1000 url...Many platforms appear to support PPPoE and also MLPPP w/LFI, but it's not clear that both features are supported on the same link.
The application is a radio that has an Ethernet interface on its terrestrial link, and acts as an Ethernet bridge. Would like to use Multilink PPPoE with LFI in order to provide LFI in order to run VoIP over lower speed links (e.g 256kb). For what it's worth, the radio also supports RFC 5578 PPPoE Extensions for Credit Flow and Link Metrics. It was fairly easy to find what platforms support RFC 5578. But RFC 5578 would be used to support variation in the capacity of the link. If the link speed is fixed, RFC 5578 is not needed. I was trying to find if the set of platforms supported increase if the need for RFC 5578 is taken off the table.
In particular, I'd be interested in the whether the ASR 9000 series supports MLPPP bundles with LFI when the links are PPPoE.
I have a static IP at home and i have setup my Westell DSL modem to bridge - like the ISP told me too. Then i change my 655 to PPPoE username and password, but when i give it the static IP, it won't connect. But when i change it to DHCP, it connects. Is this a Router issue, or a ISP issue. I am leaning toward ISP, but i wanted to check with DLink first.
I've had a DIR-615 rev b for a while and have had it set up with PPPoE sign on. The DSL modem I am using is a Motorola 2210 setup in bridge mode. All was working well. I recently switched over to dry loop AT&T dsl from AT&T dsl over a voice line.After the switch, I am unable to sign on via PPPoE using the dir-615. If I bypass the router, I am able to gain internet access via modem PPPoE sign on. I've also switched modems (Actiontec DT701D) with the same results. What has changed that would prevent the router from PPPoE sign on? I've verified that all settings on the router were the same before and after the dry loop change (including password).
I recently purchased a DIR-825 (Hardware Version: B1, Firmware Version: 2.02NA) to replace my WRT54GS v2. I hooked it on my cable modem, configure it and everything went fine until I decided to change my ISP from cable to DSL.They connected my DSL line on Friday. Today I connected an old USRobotics SureConnect ADSL Ethernet Modem 219001 (it is a bridge only model) to the telephone jack and started to configure my DIR-825.Basically I changed WAN settings from DHCP to PPPoE, entered username and password and connected.
Unfortunately, what happened was:
- DIR-825 connected and then - nearly after 2 minutes - the connection was dropped - testing with only my computer and the modem, everything went fine and fast - sometimes, DIR-825 rebooted without notice - sometimes, after saving Internet settings, it would connect only to disconnect a couple of minutes later - most of the time it remained disconnected, after clicking on Connect (STATUS page), some lights flashed, but internet icon remained orange
Well, after more than 4 hours trying to figure out what was happening, I gave up. Then, after considering buying an ADSL router, I thought about testing my old WRT54GS.Took it from the box, hooked it on the USR modem, reset to factory configuration, configured PPPoE and at the first try it connected. No disconnects, no errors, no problems.So, I have to assume that something is wrong with PPPoE on the DIR-825 in this firmware.
Then it comes to firmware. clicking on Check Now with no internet connection says: "This firmware is the latest version". Talk of misleading!!!. I then downloaded the latest firmware (v 02.06) hoping for a solution. And, watch this! "The uploaded firmware file may not be correct..." So I downloaded another file, same error message. I disconnected the WAN cable because it says also "...it is possible that the gateway may be too busy..", tried to upgrade, same error message. Reset to factory setting, tried to upgrade, same error message.
Maybe the message could say "it is possible that this is a ****py router".I'm giving up and sticking with my old WRT54GS. Maybe someday I can upgrade the firmware and "it is possible" that PPPoE comes to work with my modem and ISP.
After I am on with Tech Support for 2 hours, they say the router is defective and will not work for Port Forwarding....!!
I have installed these in many locations and have not had a problem. ALL sites had a DHCP WAN.
I have PPPoE here on FIOS, with a great connection, no issues for 4 years. But lately my Intellinet Router has had to be reset 2-3 times a day, so I replaced it with the DIR-655 RevB.
Well, only for a little bit. The Dlink will NOT Port Forward... I need it to look at cameras, Remote Desktop, etc. Tech Support and I tried PF, and Virtual and DMZ with no luck. we tried many ports, with several internal IPs.
I have another DIR-655 in stock and it has the same results...
If I plug the Intellinet back in, all Port Forwarding works fine... no problem at all to any port. BUT it still has reset issues (not related to PF...)
Anyone else have PPPoE out there, with Port Forwarding issues?
I wrote Tech Support to notify me if they ever fix this glitch, and they sent back the instructions for Port Forwarding! Do they even read what we type?
I have COX cable so DHCP would be the right way. My D-Link 655 wireless router is set for DHCP. I have a choice between PPPoE or DHCP so I pick DHCP. My wireless laptop is trying to connect to the Internet using PPPoE and won't connect. It will connect using Ethernet. How can I get my laptop on the Internet because it shouldn't be using PPPoE for wirerless?
I have TP-LINK TL-WR740N router and I am trying to configure it to work with my Broadband cable over PPPOE.The router once configured show status as connected with a proper IP and DNS servers. When I use the routers inbuilt ping utility to ping Google or any other site I get a reply.But when I connect my computer to the router on the LAN port I see no internet on my computer. I am able to ping the router address but not google.I tried disabling all Firewalls and Antivirus I have but problem still the same.Also I tried connecting over WIFI but still no internet.I also called up TP-LINK helpline several time and got my router replaced. They also tried a few settings on my machine but no success.
Region : Others Model : TL-WR740N Hardware Version : V4 Firmware Version : 3.12.11 Build 120320 Rel.51047n ISP : Blic.net (Banja Luka, Bosnia)
I'm having issues with PPPoE connection. On a daily level, my connection breaks 1-5 times. In the past, it was related to signal problems, but ISP Tech. team fixed this some 10 days ago. Now, whenever I call them they say connection was broken on user request and ask me if I'm running services like torrents.
I don't run torrents and all I have is standard windows update services, nod 32, as well as steam client.
Here's router log from today when last error occured (I "blanked" some user-specific data like my username or MAC address).
773/31/2013 17:04PPPINFOrcvd [proto=0x8057] xxxxxxxxxxxxxxxxxxxxxxxx 783/31/2013 17:04PPPINFOsent [LCP ProtRej] 793/31/2013 17:04PPPWARNINGPPPoE link down
Region : Iraq Model : TL-WDR4300 Hardware Version : V1 Firmware Version : LATEST VERSION UPGRADED ISP : Newroz Telecom
I purchased TP-link, i want to connect with ADSL modem, i connected successfully through pppoe it shows every ip through lan and wan connected, but it doesn't receive packets / bytes from internet, this is the first problem.the second problem is: i use UPS with TP-Link sometimes my electric power is low just with this tp-link it has problem and refreshing the tp-link
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
Region : Portugal Model : TD-W8970 Hardware Version : V1 Firmware Version : ISP :
Two week ago I bought the TD-W8970 ADSL router model. Im using a canon pixma IP4700 printer connected to the router USB print server port and everything is working without any issues if I just look to the router functionalities.
However since that Ive installed TP-LINK USB Printer Controller, my both computers (desktop with windows 7 and laptop with windows 8) are getting very often some BSOD.
I was editing all files automatically generated by windows on this cases and if seems that the cause of this issue is the file TplinkUDSMBus.sys (installed by USB Printer Controller).
To check the impact of this, Ive uninstalled the TP-LINK USB Printer Controller software from my laptop and I dont have any BSOD since 5 days ago. In the desktop Im still have the same issue.
The router print server is a nice functionality and I really want to use it.
Region : Argentina Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP : Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 121225 Rel.37950n ISP : Comcast
I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.
Region : UnitedKingdom Model : TD-W8968 Hardware Version : V1 Firmware Version : latest ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
when I connect my DIR-655 to the Motorola SB6141 cable modem I notice that the link speed LED on the cable modem never glows blue indicating a gigabit connection, it only glows amber indicating a lower negotiated speed. I am using a Cat6 cable between the two devices and have also tried a Cat5e cable.
When I try and force the WAN port speed to 1000Mpbs in the router interface the cable modem link speed will not light at all with no connectivity. Only resetting to Auto WAN port speed restores functionality albeit at the lower negotiated speed setting.
I'm running the DIR-655 rev B1 at 2.03NA firmware level.
I did connect the modem directly to my PC that uses an Intel Gigabit ethernet card and still had the lower connection indication (Amber) so it seems that the modem might be faulty.
Region : Others Model : TL-MR3020 Hardware Version : V1 Firmware Version : ISP :
After I configure the WAN setting on TL-MR3020, my laptop unable to connect to my TL-MR3020 anymore, the message says "windows was unable to connect to TP-LINK_POCKET_3020_B5F9AD".
Region : UnitedStates Model : TL-WR740N Hardware Version : V4 Firmware Version : 3.1 ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
Region : India Model : TL-WR740N Hardware Version : Not Clear ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
I was given an old Cisco 2611 to screw around with, no idea if it's working or not and no idea if the configs and passwords were wiped. Now my problem is that when I turn it on I don't see any console output at all.
Using 9600 baud, 1 stop bit, 8 data bits, no parity or flow control.
The power LED comes on and the activity light blinks for ~1 - 2 minutes before stopping. If I plug something into one of the Ethernet ports on the back the link light comes on for the port and the activity light occasionally flashes, from DHCP probes or something from my netbook I assume.
I have 2611xm router with 2 fastethernet ports. Now I want to install NM-1FX-TX module. I just want to conform that does 2611 supports NM-1FX-TX module. I am using this device for lab purpose. I am using latest IOS"
I have a DIR-655 that I have been using for a while (b1 revision). and suddenly I noticed my wifi speed fluctuates constantly. My lenovo Y580 sees speed drop to 130 immediately and then it can slowly progress to 1 Mbps until the hardware is all rebooted. Same happens to my Nexus 7, Dell XPS M1530 and to my roku. I have updated to 2.07 (since 2.10 is advised to avoid). And I have attempted changing channels or factory refresh.What Firmware version is currently loaded? 2.07What region are you located?
What ISP Service do you have? Cable or DSL? Cable (link speed independent of internet speed)What ISP Modem do you have? Stand Alone or built in router? Separate Motorola ((link speed independent of modem)What ISP Modem make and model do you have? Does not matter, router issue.If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. Not bridged
Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic. Independent of issue, not a factor
Turn off all devices accept for one wired PC while testing. Wired works perfect.Check cable between Modem and Router, swap out to be sure. Cat6 is recommended. Wireless issue.
A broadband speed test take before the Cisco 2611 shows 25+ Mbps. After the 2611, it drops to under 6. Consistently. The router routes between the local LAN (10.80.0.3) and a remote building across (10.13.0.2) a T1. The ADSL internet connection enters this router and leaves to a Cisco 3550 switch.
now currently i am working in networking academy. here we are using cisco 2611 and 1761 routers, i want to setup these two routers, i know the all configuring commands,
