D-Link DIR-825 :: USR219001 With PPPoE Not Working?
Nov 18, 2011
I recently purchased a DIR-825 (Hardware Version: B1, Firmware Version: 2.02NA) to replace my WRT54GS v2. I hooked it on my cable modem, configure it and everything went fine until I decided to change my ISP from cable to DSL.They connected my DSL line on Friday. Today I connected an old USRobotics SureConnect ADSL Ethernet Modem 219001 (it is a bridge only model) to the telephone jack and started to configure my DIR-825.Basically I changed WAN settings from DHCP to PPPoE, entered username and password and connected.
Unfortunately, what happened was:
- DIR-825 connected and then - nearly after 2 minutes - the connection was dropped
- testing with only my computer and the modem, everything went fine and fast
- sometimes, DIR-825 rebooted without notice
- sometimes, after saving Internet settings, it would connect only to disconnect a couple of minutes later
- most of the time it remained disconnected, after clicking on Connect (STATUS page), some lights flashed, but internet icon remained orange
Well, after more than 4 hours trying to figure out what was happening, I gave up. Then, after considering buying an ADSL router, I thought about testing my old WRT54GS.Took it from the box, hooked it on the USR modem, reset to factory configuration, configured PPPoE and at the first try it connected. No disconnects, no errors, no problems.So, I have to assume that something is wrong with PPPoE on the DIR-825 in this firmware.
Then it comes to firmware. clicking on Check Now with no internet connection says: "This firmware is the latest version". Talk of misleading!!!. I then downloaded the latest firmware (v 02.06) hoping for a solution. And, watch this! "The uploaded firmware file may not be correct..." So I downloaded another file, same error message. I disconnected the WAN cable because it says also "...it is possible that the gateway may be too busy..", tried to upgrade, same error message. Reset to factory setting, tried to upgrade, same error message.
Maybe the message could say "it is possible that this is a ****py router".I'm giving up and sticking with my old WRT54GS. Maybe someday I can upgrade the firmware and "it is possible" that PPPoE comes to work with my modem and ISP.
View 2 Replies
ADVERTISEMENT
Aug 23, 2011
I am trying to get a Cisco ASA5505 to get onto the internet using PPPOE through a Netgear DG384 ADSL router. I have the Netgear in Modem only mode - if you put it in Router mode internet access works fine. When I change it to Modem mode, the error I get on the ASA is PADI timeout. Looking through the config I think I am missing a Global NAT??Also not 100% on the best way to set the IP - we have a static IP from the ISP. Do you set the interface to use DHCP and get this address or set it statically? Then do you put the setroute option or put in a static? [code]
View 5 Replies
View Related
Oct 15, 2012
My RV180 does not route properly between LAN and WAN through my PPPoE account. I am able to ping public IPs directly from the RV180 (through the diagnose section) but can not do it from any PC on LAN. The exact same configuration works perfectly well with a Linksys WTR610N. I upgraded formware from 1.0.0.30 to 1.0.1.9 but that did not make any difference.
The only time the RV180 will route is right after I reset to factory defaults and re-enter PPPoE account name and password. If I then reset my modem or the RV180, the RV180 does not route anymore between WAN and LAN even after several minutes and even though I can ping public IPs from the RV180.
View 18 Replies
View Related
Mar 6, 2012
I'm in an issue w/ on of our ISPs. We're using an ADSL line as a secondary light load line ( 16 MBit, /w PBR in place to separate the 80 and 443 from the business-critical applications running via a SDSL link. ).
I am on a 2611 XM with IOS 12.2, mated to a D-Link 321B modem running in transparent mode. After running smoothly for weeks, for a few days now, every night some time between 2 AM and 4 AM the link would die with the dialer showing:
Virtual-Access1 is up, line protocol is down Hardware is Virtual Access interface [code]....
To my knowledge, the only option to bring it up again is to reload the box . Taking into account that the router is our DHCP server and the date gets reset to 1994, interesting effects are the outcome of resetting the box.
Well, the ISP have checked their gear and keep saying that these report a "port error" ( quite unspecific ) and blame me that I have a wrong. config in place - which is here:
interface Dialer2
description ecotel Bridge
ip address negotiated
no ip proxy-arp
[code]...
View 10 Replies
View Related
Nov 29, 2012
I recently buyed a Linksys EA6500 wireless router. I accessed [URL] to access the settings interface of the router. Went to "Connectivity Internet Settings" and chose type of the internet connection as PPPoE. Entered the username and password, clicked ok.
No internet access.
View 9 Replies
View Related
Feb 7, 2013
Have a v2 E1200. Connect with PPPoE to ISP. IPv4 works fine. With firmware included on router, 2.0.01, it would receive a /64 of IPv6 from the ISP. This /64 would show up under 'status' / 'local network'. Although it did not seem to advertise this space to PC's on my network so I was unable to use it. I updated firmware to 2.0.04. Now it does not even pick up the IPv6 /64 at all.
Anyone have PPPoE and IPv6 working? Anywhere I can download 2.0.01 to try it again?
Is there a model of router that actually works with IPv6?
View 2 Replies
View Related
Oct 24, 2012
We have an RV082 (firmware 2.0.2.01-tm),with an ADSL connection over PPPoE. It connects fine, and I can ping anything, and I can also access websites with HTTPS, but when trying to access any website with HTTP, it doesn't work.There's no load balancing going on, and it's the same whether we have the Firewall turned on or off, and everything else is pretty much as default.
View 4 Replies
View Related
Apr 23, 2011
I have a static IP at home and i have setup my Westell DSL modem to bridge - like the ISP told me too. Then i change my 655 to PPPoE username and password, but when i give it the static IP, it won't connect. But when i change it to DHCP, it connects. Is this a Router issue, or a ISP issue. I am leaning toward ISP, but i wanted to check with DLink first.
View 12 Replies
View Related
May 3, 2011
I've had a DIR-615 rev b for a while and have had it set up with PPPoE sign on. The DSL modem I am using is a Motorola 2210 setup in bridge mode. All was working well. I recently switched over to dry loop AT&T dsl from AT&T dsl over a voice line.After the switch, I am unable to sign on via PPPoE using the dir-615. If I bypass the router, I am able to gain internet access via modem PPPoE sign on. I've also switched modems (Actiontec DT701D) with the same results. What has changed that would prevent the router from PPPoE sign on? I've verified that all settings on the router were the same before and after the dry loop change (including password).
View 11 Replies
View Related
Jul 10, 2011
After I am on with Tech Support for 2 hours, they say the router is defective and will not work for Port Forwarding....!!
I have installed these in many locations and have not had a problem. ALL sites had a DHCP WAN.
I have PPPoE here on FIOS, with a great connection, no issues for 4 years. But lately my Intellinet Router has had to be reset 2-3 times a day, so I replaced it with the DIR-655 RevB.
Well, only for a little bit. The Dlink will NOT Port Forward... I need it to look at cameras, Remote Desktop, etc. Tech Support and I tried PF, and Virtual and DMZ with no luck. we tried many ports, with several internal IPs.
I have another DIR-655 in stock and it has the same results...
If I plug the Intellinet back in, all Port Forwarding works fine... no problem at all to any port. BUT it still has reset issues (not related to PF...)
Anyone else have PPPoE out there, with Port Forwarding issues?
I wrote Tech Support to notify me if they ever fix this glitch, and they sent back the instructions for Port Forwarding! Do they even read what we type?
View 2 Replies
View Related
Mar 26, 2013
I'm trying to find out what platforms support Multilink PPP with Link Fragmentation and Interleaving over a single link, when that single link is PPPoE. In searching the documentation, the best information I can find is that it seems to be supported in one direction on the ASR1000 url...Many platforms appear to support PPPoE and also MLPPP w/LFI, but it's not clear that both features are supported on the same link.
The application is a radio that has an Ethernet interface on its terrestrial link, and acts as an Ethernet bridge. Would like to use Multilink PPPoE with LFI in order to provide LFI in order to run VoIP over lower speed links (e.g 256kb). For what it's worth, the radio also supports RFC 5578 PPPoE Extensions for Credit Flow and Link Metrics. It was fairly easy to find what platforms support RFC 5578. But RFC 5578 would be used to support variation in the capacity of the link. If the link speed is fixed, RFC 5578 is not needed. I was trying to find if the set of platforms supported increase if the need for RFC 5578 is taken off the table.
In particular, I'd be interested in the whether the ASR 9000 series supports MLPPP bundles with LFI when the links are PPPoE.
View 1 Replies
View Related
Feb 17, 2012
I have COX cable so DHCP would be the right way. My D-Link 655 wireless router is set for DHCP. I have a choice between PPPoE or DHCP so I pick DHCP. My wireless laptop is trying to connect to the Internet using PPPoE and won't connect. It will connect using Ethernet. How can I get my laptop on the Internet because it shouldn't be using PPPoE for wirerless?
View 1 Replies
View Related
Nov 20, 2011
I have two DIR-615 devices, I want use first device for main AP and DHCP server and PPPoE . And use second device for Repeater.
How to work WPS and Push button on this device.
View 6 Replies
View Related
Jul 4, 2012
I have TP-LINK TL-WR740N router and I am trying to configure it to work with my Broadband cable over PPPOE.The router once configured show status as connected with a proper IP and DNS servers. When I use the routers inbuilt ping utility to ping Google or any other site I get a reply.But when I connect my computer to the router on the LAN port I see no internet on my computer. I am able to ping the router address but not google.I tried disabling all Firewalls and Antivirus I have but problem still the same.Also I tried connecting over WIFI but still no internet.I also called up TP-LINK helpline several time and got my router replaced. They also tried a few settings on my machine but no success.
View 1 Replies
View Related
Mar 31, 2013
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : Blic.net (Banja Luka, Bosnia)
I'm having issues with PPPoE connection. On a daily level, my connection breaks 1-5 times. In the past, it was related to signal problems, but ISP Tech. team fixed this some 10 days ago. Now, whenever I call them they say connection was broken on user request and ask me if I'm running services like torrents.
I don't run torrents and all I have is standard windows update services, nod 32, as well as steam client.
Here's router log from today when last error occured (I "blanked" some user-specific data like my username or MAC address).
773/31/2013 17:04PPPINFOrcvd [proto=0x8057] xxxxxxxxxxxxxxxxxxxxxxxx
783/31/2013 17:04PPPINFOsent [LCP ProtRej]
793/31/2013 17:04PPPWARNINGPPPoE link down
[Code].....
View 3 Replies
View Related
Jan 9, 2013
Region : Iraq
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : LATEST VERSION UPGRADED
ISP : Newroz Telecom
I purchased TP-link, i want to connect with ADSL modem, i connected successfully through pppoe it shows every ip through lan and wan connected, but it doesn't receive packets / bytes from internet, this is the first problem.the second problem is: i use UPS with TP-Link sometimes my electric power is low just with this tp-link it has problem and refreshing the tp-link
View 1 Replies
View Related
Sep 27, 2012
i have a d-link wireless router model DIR-601 and all the lights keep turning on and off besides the power
View 1 Replies
View Related
May 16, 2008
How to unblock limewire cuz its not working after i installed a DIR-655 at home.
View 3 Replies
View Related
Jun 6, 2012
I have bricked my DIR-825 when performing an upgrade of DD-WRT. Now I am not able to go on to the Recovery Web page. ( 192.168.0.1 ) after performing the 30/30/30 rule, wich always worked before.
I had done an update of dd-wrt and lost all of my wireless adapters, they said to load open-wrt, find the caldata and write this. This all worked. But after a reboot, the deviced bricked on me .
View 3 Replies
View Related
Jul 18, 2012
I just upgraded from DIR 615 to DIR 655. I used the installation CD but I have no wifi signal detected. Wired connection with 655 works though. If I go back to 615, wifi works.
View 1 Replies
View Related
May 4, 2011
I'm having problems connecting my ip phone with DIR-615.I got a plug and use ip phone from vocalocity, it's actually from the office where we also had the same problem and a the end we just changed to a different router coz we didn't have time to look for solutions, anyways i brought one of the phones to my house and plugged it to the d-link but it's not working.
View 12 Replies
View Related
Oct 15, 2010
I tried to find an answer to my issue however came up short. Did find,url... but that for a 600 not 601. I have "Mac filtering on and to only ALLOW the addresses below" however, it allows any computer, even if i do not have them listed.
View 3 Replies
View Related
May 19, 2011
Recently, something weird occurred. My Motorola Surfboard cable modem (on PenTeleData/Service Electric) and my D-Link DIR-655 don't seem to be getting along.If I plug a network cable directly from the modem into a computer, it works fine. However, if I go from the modem to the router's WAN port, it doesn't seem to want to connect to the router at all (no matter what DNS settings I change on the router (including spoofing the MAC address of a working computer) or which network cables I use; the "activity" light on both the router and the modem remain off).Also, if I take a network cable and plug one end in one of the LAN ports on the router and the other end in the WAN port, it works (well, the "internet" activity light on the front of the router comes on and the status page at http://192.168.0.1/Status/Device_Info.shtml says "Cable Status: Connected; Network Status: Incorrectly configured - check logs" instead of "Cable Status: Disconnected; Network Status: Disconnected").
View 11 Replies
View Related
Apr 3, 2011
how to get web logging working? I set up an Access Control policy for web logging only for one machine on my network. I also turned Syslog on and have Kiwi syslogd running on my desktop. However, it's not logging web traffic. how to get web logging working correctly?
View 4 Replies
View Related
Oct 17, 2011
I have Ver E3, with firmware 5.10. Like it says above, Wireless N is not working. I've already going into Manual Wireless set up and selected Mixed G and N. All of my devices will connect, but only as G devices.I'm reluctant to set it to "N only" for fear that none of my devices will be able to connect.
View 14 Replies
View Related
Mar 14, 2013
The 5 GHz has been working for 2 months but now, no longer available. No visible 5GHz wireless network. Reset to factory setting and reinstalled but still no 5 Ghz. The 2.4Ghz is working fine.
Location Australia
fcc id: KA2IR835A1
IC: 4216A-IR835A1
P/N: IIR835NAU...A1E
S/N: QBKA1C5001387
WPS PIN: 24784784023
H/W Ver: A1 F/W Ver: 1.01
View 1 Replies
View Related
Feb 19, 2013
I have a D-Link DIR-615 router and can't get the internet working and have done everything possible to get it working. the globe light which is the internet light will not turn from amber to green. I have done a factory reset which is why this occurred in the first place. After the reset the globe stayed orange and the internet refused to work now everything is up but the wireless will not work nor the internet I have gone through both the manual set up and set up wizard and tried all options.
View 8 Replies
View Related
Nov 11, 2011
I have been using a d-link router for some time now and since yesterday it has stopped working ( I have an orange 'world' light on all the time) After looking around this site I have tried resetting etc and nothing works. If I plug the ethernet cable into the modem I can get on the internet if I plug the cable into the router then nothing. These are the details I got from the config all when I plugged the ethernet into the router.
View 3 Replies
View Related
Mar 3, 2011
I have a D-Link wireless adapter (DWL-G122) that I have been trying to install on a Windows XP computer. After various uninstalls and reinstalls of the drivers and programs that come with it, I have found currently the best way to get it to work is leave the D-Link programs uninstalled and have Windows install the driver itself.The problem is, it doesn't seem to keep the drivers on restarting, so every time the computer is restarted, it must be installed again. This is not ideal.It occasionally worked when I installed from the CD, but the D-Link programs that would install with the drivers created problems of their own.
View 2 Replies
View Related
Jul 10, 2011
My router suddenly stopped working yesterday and I've tried everything I can think of to fix it. I have one computer wired directly in to it and a few laptops that use wireless connections.The power LED and the internet LED light up, but the status LED and the WLAN LED do nothing. Pushing the factory reset button on the back doesn't seem to do anything.Can't connect to the router site (192.168.0.1) The internet works fine when I plug in to it directly, so its definitely the router.
View 3 Replies
View Related
Jan 29, 2012
I bought a TP-Link TL-WR841N which i have managed to setup up properly, i am able to connect to the wireless and get internet access. However the minute i walk out of the room or a few meters away i am disconnected and i can't re-connect, i get the "windows cannot connect to TP-LINK" message. The signal strength in on excellent and i know it works because when i stand near it, it works perfect.I phoned TP-LINK technical support who were pretty useless and couldn't fix the problem.
View 3 Replies
View Related
Jul 20, 2012
im deployment and we have hardwire internet in my room. wanting to use all other devices eg. iphone and what not i bought a router to plug the hardwire in to and run the wifi off the router for all devices. its made by TP-LINK the model is TL-WR940N. it worked great for a while but then kept giving me DNS server is not responding but i could plug the hard cable in my computer and the internet would work fine? so i reset the router and set it all up again like before. Now i cant get it to run wifi off it anymore it recognizes and connect through wifi but no internet and its telling me i need to plud the hardwire in to my internet but my computer is recognizing it and saying i have internet access, but no internet i mean its not even thinking if there is internet.
View 1 Replies
View Related
May 7, 2011
I have a Dir 655 router how can I know if one of the antennas is working right?
View 5 Replies
View Related
