The 5 GHz has been working for 2 months but now, no longer available. No visible 5GHz wireless network. Reset to factory setting and reinstalled but still no 5 Ghz. The 2.4Ghz is working fine.
Location Australia
fcc id: KA2IR835A1
IC: 4216A-IR835A1
P/N: IIR835NAU...A1E
S/N: QBKA1C5001387
WPS PIN: 24784784023
H/W Ver: A1 F/W Ver: 1.01
I have a DIR-825 router connected to my cable modem. The 2.4ghz constantly goes down but not the 5.0ghz. Our wireless devices will see the connection but we are unable to connect.We only have one device that uses the 5.0 and multiple devices that use the 2.4 and none of them can connect.I am currently running firmware 2.02. I also notice that the time changes and I have to reset the time/date.I have tried rebooting the device, resetting the router, changing the network key, updated the time/date, renewed the DHCP...I don't know why it keeps going down, why the time/date keeps changing, and why I cannot get the 2.4 working.
View 13 Replies View RelatedI have a dir-825 and wireless clients connected on the 5ghz ssid can see clients on 2.4 ssid and also out to the WAN (internet) but can't see any clients (my NAS ) connected to the dir-825 wired lan.2.4 ghz clients see everything fine. same with clients connected through the wired lan. I've tried DHCP and static ips. no idea what to do next.I was originally on 2.02 fw and have tried 2.03, 2.05 and now 2.06I'd really like to keep the 5ghz on because I have an AP by my tv and several devices connect from there to stream from the NAS.
View 2 Replies View RelatedHow come my 2.4GHz client can't see my 5GHz client? Shouldn't they be visible through the DIR-825 router?
View 1 Replies View RelatedI just bought the D-link router DIR-815. I set both bands on but when I connected the blue-ray disk for streaming Netflix movies it connected on the 2.4 Ghz. How do I set up the 5Ghz band?
View 3 Replies View RelatedWe've been using an 655 in an NGO office that has grown to 20+ computers in two buildings (next to each other). The 655 doesn't seem to be handling that many clients very well so I want to get another one (perhaps a more powerful unit). We will stay operating on 2.5Ghz, have one of the units act as an AP in the other building (too bad we can't bridge with these). Most of the router activity is LAN based (server, etc). Our Internet connection is only 256kbps satellite (and is proxied first through the server). But the LAN performance is not good when many clients are active and some services on the router will freeze and require reboot several times a week, assuming b/c it's overtaxed.
1. know if the 825 will perform better in in 2.5ghz only mode than the 655? Seems that it has more RAM. Newer processor too? The tests I saw online showed that the 655 outperformed the 825 in simultaneously connections, but I assume that was probably in dual mode. I want to know if the 825 will be better in 2.5ghz only mode. We won't need 5ghz mode.
2. Is there another newer DLink I should consider that would provide better capacity and throughput on 2.5ghz only? However, it is ciritical that we keep the same feature set for security (IP based access control rules to various IP ranges on the Internet).
3. It would be awesome if some DLink supported even more sources and/or destinations per access control rule. We use these extensively and the 655 B1 2.01 build has several bugs for access control rules. Is there any DLink that has more robust access control or is it about the same for all?
I installed my 1522 today with a Direct TV receiver and made a connection using AP mode.
How do I know what band is being used and how to switch between the bads.
How i can connect to my 5ghz wifi through my xbox ?
View 5 Replies View Relatedi have a d-link Dir-825 (Hardware Ver. B1/Firmware 2.02NA) and i wanna connect my ps3 to the 5ghz for online gaming but i cannot find the option for it. also when scanning on my iPod Touch and PS3 for a wireless connection i cannot find the SSID that i named for 5ghz and the only one that shows up is the other SSID i named for 2.4ghz.(both SSID are not the same name). is it really worth switching from 2.4ghz to 5ghz?
View 4 Replies View RelatedHave hooked up a DIR-825 to an iMac and it works well on 2.4GHz band. Having issues seeing 5GHz band as it comes and goes. Just today bought a DWA-160 USB adapter hoping it would connect the kid's PS3 to the 5GHz band but the PS3 wont accept or recognize either the DWA-160 or the 5GHz band.
Can't find any solutions in the manuals.Desperate for a fix as the wife and I want to be able to work on the 2.4GHz without being constantly kicked off by the kids on the PS3.
What is the 5GHz antenna orientation in the DAP-1522? If I want to get the best signal for streaming to a DSM-750 how should I orient the the DAP-1522? Horizontal? Vertical? and which edge towards the media player?
It's working but the access point only reports about 50% signal strength over 20 feet (and only 1 wall) so I would have expected better. I've tried turning the box a couple of different ways but didn't see any big difference in the reported signal strength.
Hardware Version: C1
Firmware Version: 3.00
Wired works normally, and wireless is otherwise stable, except when under heavy load. E.g. if I initiate a large TimeMachine backup over wifi to my NAS, it will fail and the wifi will drop requiring a power cycle.I have tried a similar transfer over ethernet (~1.7Tb) and although the transfer speed wasn't great (~10MBs, likely due to NAS drive bottleneck), it completed without a problem.
If I try copying ~150Gb over wifi, however, it barely lasts 30 minutes without dropping out.Once the wifi drops, it still connects, but nothing works (I am unable to even connect to the web interface using the local IP). Other devices connected already via ethernet or 2.5Ghz still function normally, but the 5Ghz just fails, and if I try initiating a new connection to the 2.5Ghz it doesn't work until I power-cycle the router.As far as overheating goes, I'm not sure it is an environmental issue... I have the router standing upright in an open space so there is good airflow around it.
I Recently purchased the DAP1522 to use as an entertainment bridge for my xbox 360, BR player and dish network receiver I also upgraded my router a WRT5GS running tomato to a Linksys E4200 going from G to N while i had my Xbox and BR connected wireless I didn't have the Dish receiver hooked up so i thought by using the DAP i would be upgrading my network and connecting my Dish receiver no brainier right and everything works so far.But here's the question with all the hype of the benefits of the 5ghz channel , well it's not hype it certainly makes sense but from what I see the products have to be compatible shouldn't what I'm connecting be compatible they say your gaming console specifically and streaming movies i would think . Any configuration tips I read somewhere that with an E3200 router they had to set the 5ghz channel to like 37 for the DAP to see that channel its all getting a little overwhelming here's whats in the house A Mac Power PC pre Intel using a Asus NB13 USB 2.4ghz its the only thing i could find with speeds over 100Mbps A windows 7 machine hardwired gig connection another windows 7 pc downstairs hardwired a netbook with a wireless connection and lastly a DECT 6.0 phone system who knows what interference these produce.
View 1 Replies View RelatedIn the old days I used two autonomous 1242AG access access points to create a 5GHz PtP link with 2 patch antennas (over small distance 50meters and on on private premises) to connect an small building or garage were there was no ethernet availible. and used the 2.4GHz radio to serve clients in the small building area, worked great.
Can I use the same setup with the 2602e access points? If so, would I be able to use them controller based? Can I connect a switch/or additional access point behind the 2602e (bridge) in the small building/garage? Would that addtitional access point be able to connect and register to the WLC.
I recently modified my home network in hopes of getting faster file transfers between devices. But it looks like something's not right.I'm suing Lan Speed Test and the best performance I get over WiFi is about 44Mbps (avg.). From my laptop to my NAS. If i turn off the WiFi and do the test over a wired connection the best I get is 200Mbps (avg.).
1. AT&T 2Wire cable modem. Internet comes in the house through this box and it's currently set up to be in bridge mode so that the TPLink router handles everything.
2. TP-Link WDR3600 gigabit/wireless router set to work in 5Ghz only, 11an mixed mode.
3. WD My Book Network Storage. Wired gigabit connection.
4. Desktop PC. Wired gigabit connection.
5. Laptop PC. Wireless.
6. 1 ipad v.2, 2 iphone v.5. Wireless.
Current setup:
1. internet cable goes into 2Wire Modem.Wireless on this device is OFF.
2. cable goes from LAN port on modem to WDR3600 router's internet port
3. cables go out from router to Desktop PC and NAS
4. all other devices are connected to the 5GHz wireless network created by the router.
Region : Germany
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : Build 121225 Rel.37950n
I have low signal range from this WDR4300 router on both bands and especially on 5Ghz i lose my connectivity on just few meters away from the router and on other rooms in my 80m2 apartment, i also own another tp link 740n with only one antenna and the range is better with it almost covers all my apartment. Router has been reset after being updated to latest firmware and tried different configurations but im not satisfied with the signal range. Is there something i can do.
i have a d-link wireless router model DIR-601 and all the lights keep turning on and off besides the power
View 1 Replies View RelatedHow to unblock limewire cuz its not working after i installed a DIR-655 at home.
View 3 Replies View RelatedI have bricked my DIR-825 when performing an upgrade of DD-WRT. Now I am not able to go on to the Recovery Web page. ( 192.168.0.1 ) after performing the 30/30/30 rule, wich always worked before.
I had done an update of dd-wrt and lost all of my wireless adapters, they said to load open-wrt, find the caldata and write this. This all worked. But after a reboot, the deviced bricked on me .
I just upgraded from DIR 615 to DIR 655. I used the installation CD but I have no wifi signal detected. Wired connection with 655 works though. If I go back to 615, wifi works.
View 1 Replies View RelatedI'm having problems connecting my ip phone with DIR-615.I got a plug and use ip phone from vocalocity, it's actually from the office where we also had the same problem and a the end we just changed to a different router coz we didn't have time to look for solutions, anyways i brought one of the phones to my house and plugged it to the d-link but it's not working.
View 12 Replies View RelatedI tried to find an answer to my issue however came up short. Did find,url... but that for a 600 not 601. I have "Mac filtering on and to only ALLOW the addresses below" however, it allows any computer, even if i do not have them listed.
View 3 Replies View RelatedRecently, something weird occurred. My Motorola Surfboard cable modem (on PenTeleData/Service Electric) and my D-Link DIR-655 don't seem to be getting along.If I plug a network cable directly from the modem into a computer, it works fine. However, if I go from the modem to the router's WAN port, it doesn't seem to want to connect to the router at all (no matter what DNS settings I change on the router (including spoofing the MAC address of a working computer) or which network cables I use; the "activity" light on both the router and the modem remain off).Also, if I take a network cable and plug one end in one of the LAN ports on the router and the other end in the WAN port, it works (well, the "internet" activity light on the front of the router comes on and the status page at http://192.168.0.1/Status/Device_Info.shtml says "Cable Status: Connected; Network Status: Incorrectly configured - check logs" instead of "Cable Status: Disconnected; Network Status: Disconnected").
View 11 Replies View Relatedhow to get web logging working? I set up an Access Control policy for web logging only for one machine on my network. I also turned Syslog on and have Kiwi syslogd running on my desktop. However, it's not logging web traffic. how to get web logging working correctly?
View 4 Replies View RelatedI have Ver E3, with firmware 5.10. Like it says above, Wireless N is not working. I've already going into Manual Wireless set up and selected Mixed G and N. All of my devices will connect, but only as G devices.I'm reluctant to set it to "N only" for fear that none of my devices will be able to connect.
View 14 Replies View RelatedI have a D-Link DIR-615 router and can't get the internet working and have done everything possible to get it working. the globe light which is the internet light will not turn from amber to green. I have done a factory reset which is why this occurred in the first place. After the reset the globe stayed orange and the internet refused to work now everything is up but the wireless will not work nor the internet I have gone through both the manual set up and set up wizard and tried all options.
View 8 Replies View RelatedI have been using a d-link router for some time now and since yesterday it has stopped working ( I have an orange 'world' light on all the time) After looking around this site I have tried resetting etc and nothing works. If I plug the ethernet cable into the modem I can get on the internet if I plug the cable into the router then nothing. These are the details I got from the config all when I plugged the ethernet into the router.
View 3 Replies View RelatedI have a D-Link wireless adapter (DWL-G122) that I have been trying to install on a Windows XP computer. After various uninstalls and reinstalls of the drivers and programs that come with it, I have found currently the best way to get it to work is leave the D-Link programs uninstalled and have Windows install the driver itself.The problem is, it doesn't seem to keep the drivers on restarting, so every time the computer is restarted, it must be installed again. This is not ideal.It occasionally worked when I installed from the CD, but the D-Link programs that would install with the drivers created problems of their own.
View 2 Replies View RelatedMy router suddenly stopped working yesterday and I've tried everything I can think of to fix it. I have one computer wired directly in to it and a few laptops that use wireless connections.The power LED and the internet LED light up, but the status LED and the WLAN LED do nothing. Pushing the factory reset button on the back doesn't seem to do anything.Can't connect to the router site (192.168.0.1) The internet works fine when I plug in to it directly, so its definitely the router.
View 3 Replies View RelatedI bought a TP-Link TL-WR841N which i have managed to setup up properly, i am able to connect to the wireless and get internet access. However the minute i walk out of the room or a few meters away i am disconnected and i can't re-connect, i get the "windows cannot connect to TP-LINK" message. The signal strength in on excellent and i know it works because when i stand near it, it works perfect.I phoned TP-LINK technical support who were pretty useless and couldn't fix the problem.
View 3 Replies View Relatedim deployment and we have hardwire internet in my room. wanting to use all other devices eg. iphone and what not i bought a router to plug the hardwire in to and run the wifi off the router for all devices. its made by TP-LINK the model is TL-WR940N. it worked great for a while but then kept giving me DNS server is not responding but i could plug the hard cable in my computer and the internet would work fine? so i reset the router and set it all up again like before. Now i cant get it to run wifi off it anymore it recognizes and connect through wifi but no internet and its telling me i need to plud the hardwire in to my internet but my computer is recognizing it and saying i have internet access, but no internet i mean its not even thinking if there is internet.
View 1 Replies View RelatedI have a Dir 655 router how can I know if one of the antennas is working right?
View 5 Replies View RelatedIt worked fine with my last router. It just doesn't seem to connect securely. It comes up under my iTunes, but once I go to enter the code, it doesn't show up as completed. Also, a utorrent monitoring app cannot connect to my computer, which is set up right at my computers end, but won't connect at all from my phone over wi-fi.
View 14 Replies View Related