Connecting Netgear R6300 Wifi Router To Old Gateway?
Oct 3, 2012
I have been using a cable modem gateway - Netgear CGD24G from Charter for two years. I just bought Netgear R6300 wifi rounter in order to upgrade the speed and range for my internet. My goal is to upgrade 802.11g to 802.11ac. Is there any special way to setup it up? Or do I need to contact Charter to replace a new gateway?
I recently upgraded my wireless router to a Netgear R6300 and have had no problem with the wireless speeds,35mbps down and 6mbps up according to speedtest.net. I experience similar speeds from my direct wired connection as well but I am having an issue with my speeds running through my Linksys PLE300 powerline adapter I am getting speeds of 4mbps down and 6mbps up. My PC is running Vista Home Premium SP2 (I know). Prior to the upgrade I was using a Netgear N600 and I was getting much faster speeds through the powerline. My NIC is a Intel 82566DC -2gigabit. I checked all the cables, I am using a CAT6 from router to Powerline and when I run router stats it shows WAN as 1000M/full and LAN1 (powerline) as 100M/Full.
Generally we have three people on the wifi at once, being online research, socializing (skype, ect.), and gaming. I want the best for everyone, and Ive had a Netgear router and still do, but its like wearing out. Its off and on functioning. I havent had a linksys so I have no base for those. We have windows8 and windows7 and an apple iPad on at once, generally. Im not sure if these routers are windows8 compatible..
I am running an i7 MSI gt683 with windows 7 with an Intel Centrino Wirelss-N 130. My home wifi connection runs off of comcast on a netgear router, and the wireless connection works on every single device in the house except for my laptop. I can run my ps3, my wii, we have an ipad, all our phones can connect and we have another laptop that connects with no issue. I have updated my drivers for my wireless card to the latest, flushed the ip on my desktop that the modem is connect to a dozen times. The only way to sometimes fix it is to manually log in to my router and release/renew the ip address from there. Sometimes it will work, sometimes it won't. When it does work, it will work for about a week and then stop working for no reason at random times.The errors I keep getting are:Identifying network (which runs infinitely before cycling back to no internet connection)Connected with no internet access.
I have 3 computers wired to a Netgear R6300. Two of those computers (both running XP SP 3) I added new LAN Gigabit Cards (Tenda TEL9901G) . One recognized the card right away and had no issue connecting to the Internet (using this computer now). The other shows a 1.0 Gbps connection but I can not get any web pages to come up. I can access other computers and devices on the network without an issue on the computer that doesn't connect to the Internet.
If I type in the web address it says "Server Not Found." If I type in the IP address it will come up with the name of the site in the address bar but it still says "Server Not Found." I've tried several times to unplug the router and modem (Motorola Surfboard) and restart everything but the problem was still there. Also, I tried other Ethernet cables and no change. The LAN card drivers are up to date but I don't think the card is the issue since I swapped the new cards (to see if the card was the problem) and it does show a 1.0 Gbps connection. Also, tried uninstall/reinstall, disable/enable the card many times.I didn't change any setting in the router after installing the cards.Here is the ipconfig output:
I´ve recently purchased a Netgear r6300 and a wifi ac bridge (Linksys wumc710) When hooking up my Readynas Pro to the r6300 via the wumc710 I only get transfer rates at max 8MB/s. That´s not very impressive, and even with the bridge located within 10 feet of the router, no walls in between. What am I doing wrong? I´ve set the MTU on the Readynas and the r6300 to 1500.When doing a wired test between the r6300 and the Readynas Pro I can copy a file from the Nas to desktop at approx 80-100MB/s, but with wireless ac via the wumc710 only at 4-8MB/s.
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings: IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
I recently bought a Sony Bravia HD TV with wireless internet capabilities. When I try to connect to my wireless internet. The TV finds our wireless router name, but when we try to finally connect wirelessly it gives the following message: TV wi-fi found, local access failed and network access failed. The router we have is a Netgear PK500.
On the TV we have three differant ways for the tv to locate the router they are by scanning, the WPS button and by entering the WPS pin. We've tried all three and got the above message.
I bought a netgear n600 wnda3100vs wifi adapter for my desktop.I installed it and everything. Now when I try to connect, it finds my router, but for some reason it will not connect. My router is a 2wire that runs on 802.11g[CODE]
Netgear WNR2000 router. Macbook Pro with Snow Leopard connected to router through wireless. Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
I have a WRT300n router and want to connect to my Uverse Gateway. When I connect them & try to use the internet connection I get an error that says a connected router must be capable of using DYnamic IP addresses.
My NetGear router stopped connecting to the internet. The internet light, which is usually orange, is now yellow and flashing. I tried rebooting everything and now, when it connects it says "local access" so I can't get on the net
Ive been having problems with the Wireless connection on my laptop for a while now. Basically even though the signal strength is shown as excellent and hovering over the little monitor in notification area shows "Internet access" i cannot connect to the Internet via WiFi. The strange thing is when i connect an Ethernet cable the signal strength on the bottom goes up and i get Internet access but the computer seems to think its got a wireless connection, even though its actually a wired connection. Ive already tried the following
Driver Update Windows Update AntiVirus/Malware Scan Firewall/Anti Virus Off Ethernet Connection Disabled and Enabled Changed router channel reset wep key numerous times Network Scan (no problems found)
Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.110408-1631) Processor: Intel(R) Pentium(R) CPU P6200 @ 2.13GHz (2 CPUs), ~2.1GHz Memory: 4096MB RAM Available OS Memory: 3892MB RAM
How do you connect two routers together to increase signal through the whole house? I am trying to use the n300 as my main router (its hooked to cable modem) and use the 2wire as an access point.The two are connected by a known good ethernet cable.
I have a netgear CVG834G main router, were my desktop is plugged on to.I pulled a new cable trough the house and garage to have internet access on the other side (cable length is about 80 meters).After the 80meters of cable I placed a Linksys WRT54GS v5.1 router. The problem is that I can connect to the Linksys, but the Linksys can�t connect to the netgear. On the Linksys the internet LED is blinking very slowly (what does this mean?). So first I thought that the cable was broken or too long. I tested the cable => not broken. I connected the Linksys with the netgear trough a shorter cable and then connected my laptop via the long cable (80meter) and this works perfectly.Is the maximum distends a netgear can take less than 80 meters? (thought is was 100meter ).
Im having problems staying connected to my internet. I have Verizon Fios router that is wired into this desktop i also have 2 laptops and now im trying to connect a second desktop wirelessly to the router. My Netgear Rangemax PCI picks up the signal at 68% and connects to the router. But periodically it disconnects from the router and i click connect to a network icon and it shows that i have no wireless internet as if no PCI card is installed so i wait a min then it shows up again and windows network diagnostic kicks in and "resets the network adapter" and all is well for about 15min till it disconnects again.
hrome threw me a DNS lookup failed. I go into my network settings and I noticed that I had limited connectivity. It would switch between no network access and no internet access every few seconds. After a bit of fiddling around, I got it to connect through assigning myself a static IP. This isn't exactly convenient because I use this computer on multiple networks. When I try to have it on automatic IP, I get no IP address or default gateway when I do an ipconfig /all. It would appear that my router quit assigning my laptop an IP for no reason whatsoever. DHCP is enabled on the router, and all other devices work fine. What could possibly be the problem here? I'm 99% sure it's not an IP conflict either. It's not being MAC filtered because I'm on the thing right now posting this through a static IP. It's not my A/V because it's worked great in the past. Perhaps I should also mention it occasionally says "unidentified network" instead of the SSID
I've got an Optus (in Australia, so 3G mobile broadband is all that matters I would think) that I'm trying to connect to a Netgear WGR614v9 wireless router. So the 3g mobile plugs into usb on computer; the router to the ethernet card on computer.
I know; I could buy one that has it in one package, but we're throwing the router out from work anyway. If this works my daughter will be thrilled with her iPod more is all :)
I've got the mobile broadband on, and plugged in the router and Windows 7 makes a second network connection automatically for the router, though with no internet access, and the setup wizard in the router claims to have no access to the internet. (though clearly I'm posting...lol).
We can see the Wireless signals on devices and can connect to the router but then the devices say no internet access when you actually try to access the web, like the router wizard does. and yet, we are online
I am trying to connect a wireless router (EDIMAX br-6228nc) with a ADSL router (NETGEAR). i assigned the LAN IP of the ADSL modem to 192.168.1.1, subnet mask 255.255.255.0, and enable DHCP server.then i connected a LAN port from ADSL router to the WAN port of the wireless router. i assigned IP of the WAN port of wireless router to 192.168.1.10, subnet mask to 255.255.255.0 and default gateway to 192.168.1.1 now on the LAN side of the wireless router i assigned IP 192.168.0.1 and subnet mask 255.255.255.0 enabling DHCP server.on the client pc i selected the setting of automatically assign IP setting (which it got 192.168.0.100, default gateway 192.168.0.1) but my client pc is not able to access the internet.
I am having problems connecting my PC (Win7) to my Router (Netgear DGN2000) via ethernet cable.Wi-fi is working fine but I want to speed up my connection using the PC's Gigabit port. Here are the problems:
- When connecting via wi-fi everything is fine
- When enabling my LAN WITH wi-fi still enabled I lose all internet connectivity
- When enabling my LAN and disabling wi-fi lose all internet connectivity
Here is my IP Config when both are enabled :
Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved.
I am having trouble getting the wrt610n to connect to the wnr2000v2 that can be set a wireless repeater. I had a 160n hooked up and it was working fine, but am unable to get the 610n going on it. setting this type of networking up , but have a general idea of how it works. I have the 610n running and is broadcasting a signal, but the wnr 2000 will not connect to it wirelssly and repeat it. The setup in the netgear is pretty basic , but I am new to the linksys 610n and the interface that's why I believe it has to do with the 610n.
I recently set up my netgear wireless gateway (cgd24g).I am able to connect to the internet with it through an ethernet cable, but have so far been unable to connect wirelessly.I've tried changing my SSID in the gateway's settings and applying WPA encryption, but when I search for my wifi network, I just see the default SSID.
The laptops in my flat are wirelessly connected to a Netgear N150 Wireless router and the connection is forever going from little to nothing. I've tried resetting everything, getting Orange to replace the router (a new Netgear N150) but still nothing. I've tried changing channels in the past but never seems to last. I can't work out if another wireless router in another flat is chomping into our connection
I recently switched internet service providers from AT&T to Time Warner and ever since I have been unable to connect to my Netgear router with my computer's wifi. However, I have successfully connected my TV wirelessly to said router. One other note, my computer's wifi seems to recognize that the netgear router is there but it just refuses to connect me to the internet
I'm posting from my phone because right now its my only access.I have a Netgear Router model number WNR2000I have a Gateway GM5260 model computer using windows xp.I am currently trying to connect to my awesome neighbor's wifi connection that they so lovingly bestowed on me and my family the other day.Herein lies my problem:I cannot get their router and my own to connect. I'm a networking noob and could really use some assistance.I've got a their wireless password, my router, and my ethernet cable connecting my router to my pc.Do I need to pick up a wireless antenna to connect to my router as well?