Locate The WPA Passphrase For Netgear 7550 Gateway?Jan 21, 2013
locate the WPA passphrase for netgear 7550 gateway?
locate the WPA passphrase for netgear 7550 gateway?
What is the default gateway so i can password protect my wireless??View 1 Replies View Related
I have at&t DSL.I NEEDED to upgrade my wireless gateway from the 2wire wireless-G gate way that I had.I also have a Netgear WNDR-4000 750N Wireless Dual Band Router.
I know I needed an at&t modem to run my DSL, so I purchased (before reading reviews) a Netgear 7550 Wireless Gateway from at&t (they did not have any "N" single user modems (if there is such a thing).I have read through other posts that it is possible to connect the two and I would not need the 7550 for anything else but a modem (disabling broadcast).
The question is ... do I REALY need to do all this or can I just get away with the 7550?Or will the Netgear WNDR-4000 750N Wireless Dual Band Router, if installed and used, fix some of the issues that other 7550 users have said in other posts?
Wireless ... I have 3 gaming systems, two PC's, a tablet and 4 smartphones.I will be using 3 wired ports ... 1 gaming system, PC, and a blue-ray.
And yes, my 2wire wireless-g gateway ran all these ... not efficiently or reliably, but they all did run.
I have not received the Netgear 7550 yet, just trying to get some opinions on which setup would be better.
ATT just sent me a replacement Netgear 7550 ADSL Gateway. I previously had a 2Wire modem that could connect with my Mac desktop and Toshiba laptop without issues.Now my Mac is up and running wireless on the new gateway (no problem), but the laptop (Windows 7) is not connecting and Windows troubleshooting goes not resolve the problem. It will connect via Ethernet but ATT could not get it on wireless. The ATT tech signed on the the laptop and could not get it done.View 1 Replies View Related
I just recieved the netgear modem model 7550 from frontier. when i try to connect to the wifi i get a message saying that it is connected but there is a lock symbol on the wifi icon. i have entered in the password but it does not change anything?View 1 Replies View Related
I need to find out the default log in and password for the model 7550View 1 Replies View Related
any way to boost the wifi signal coming for the netgear 7550 ? Mine is very weak and this is the 2nd replacement from at&t.View 1 Replies View Related
Tried numerous times but no Internet connection between Directv hr23-700 and Netgear DSL 7550 modem/router. Is connected to home network, but no Internet.View 1 Replies View Related
I have a new Netgear WN2000rpt extender and cannot get past passphrase on the install wizard...nothing happens after I enter my passphrase and select "continue"..View 1 Replies View Related
I recently set up my netgear wireless gateway (cgd24g).I am able to connect to the internet with it through an ethernet cable, but have so far been unable to connect wirelessly.I've tried changing my SSID in the gateway's settings and applying WPA encryption, but when I search for my wifi network, I just see the default SSID.View 1 Replies View Related
i cant get my netgear to work on my gateway can youView 1 Replies View Related
Here is my setup:
Netgear WNR2000 router.
Macbook Pro with Snow Leopard connected to router through wireless.
Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
I have been using a cable modem gateway - Netgear CGD24G from Charter for two years. I just bought Netgear R6300 wifi rounter in order to upgrade the speed and range for my internet. My goal is to upgrade 802.11g to 802.11ac. Is there any special way to setup it up? Or do I need to contact Charter to replace a new gateway?View 7 Replies View Related
about two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1View 2 Replies View Related
i forget the network secutity keyView 1 Replies View Related
I can't print from my wireless printer. It wants to know my WPA security pass phrase. Where do I find this?View 3 Replies View Related
where do i find the wirelesswpa security passphraseView 1 Replies View Related
I have had to re format vista and reload my WiFi. My internet connection using an ethernet cable to my LAN works ok but when the ethernet cable is removed and I click "connect" I am asked for my security key or passphrase. How do I find this information or preferably remove the request for it?View 1 Replies View Related
I need to re-configure the passphrase configured on my HP printer.How do you run the wireless network set-up in order to re-enter my wireless network WPA security passphrase?View 1 Replies View Related
I have a passphrase for my router that I need changed but I don't know how. I was told that if anyone knows my phrase word that they can access my router.View 1 Replies View Related
I have windows vista and a Atheros adapter?is there a way to just go through control pannel?View 2 Replies View Related
i cant connect to a wireless network with my laptop coz it keeps coming up with enter security key or passphraseView 2 Replies View Related
A few months ago, I purchase, installed and configured a WRT 160N V3. And I couldn't be happier. I now would like to go back and change the passphrase that a user needs to enter when they connecting to my router. Currently it uses the default value. And I would like to make it a bit more friendly. I found a number of postings dealing with setting retrieving or changing the Admin password.
But I was not able to find anything on changing the “passphrase”. There probably are a number of postings on the subject, and I simply overlooked them.
Is there a difference between (1) the Router Password (on the Admin tab of the web-based utility), (2) the Wireless Security Passphrase (on the wireless security tab of the web-based utility) , and (3) the password on the Router Settings in the Cisco Connect application?View 2 Replies View Related
My wife has a laptop that we want hooked up to the internet through our linksys wireless router. But I cannot remember my security key or passphrase needed to get her on the connection. How do I recover, or find, it?View 9 Replies View Related
I've just hooked up my previously used N300 router. The router is showing a solid green light, and the laptop recognizes that a solid Belkin wireless connection is out there. I cannot for the life of me remember the network key and/ or pass phrase I originally set. No, I did not tape this info to the underside of the router as suggested in Belkin instructions.View 6 Replies View Related
After a lot of effort I got my wireless adapter to work like it should without security. I set WPA 2 level security on my WRT54GS wireless router and then went to access the router (set up as an access point) with the WPC54G ver 2 adapter on a Thinkpad T22, it says I have WEP encryption and I cannot enter the passphrase I used for the router. It does not let me select AES. It says to pick AES or TKIP, but TKIP is the only choice.View 1 Replies View Related
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...View 0 Replies View Related
I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]View 1 Replies View Related
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?View 1 Replies View Related
I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?View 1 Replies View Related
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?View 1 Replies View Related
I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.View 2 Replies View Related
New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 184.108.40.206
Remote Security Gateway Type: Dynamic + Email
Email address firstname.lastname@example.org
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address email@example.com
Local Security Group Type is Subnet, with the local IP class 220.127.116.11
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.View 2 Replies View Related
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
Just bought 3 WRVS4400N, I wanted to setup gateway to gateway VPN. I followed the instructions on the WRVS4400N admin guide and VPN does not connect. I also downloaded the VPN setup wizard and that also did get the gateway connected. Everything seems to be correct. Do I have to enable anything else? Firewall setting?
Below is my config.
IPSec VPN Tunnel: Enabled
Tunnel Name: TUN01
Local Security gateway: IP only
WAN1 IP: 192.168.100.1
Local Security type: subnet
LOCAL IP: 10.10.10.1
I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?