I've been trying to connect my laptop directly to my Arris modem with an ethernet cable to get on the internet, but for some reason every time I do I have "limited access" and can't get on the internet. I can only seem to get my laptop on the internet while the wireless router is connected to the modem and then either connecting wirelessly or by connecting my laptop to the wireless router with an ethernet cable.I want to connect to the internet without my wireless router, because someone was hacking our router and was apparently doing illegal downloads. We got a cease and desist letter that said our internet will be terminated if it happens again, so I want to connect to the internet without any wireless connections being set up.
I just switched ISPs and received a new modem, unfortunately I can't seem to connect my laptop online with this. Everything else connects fine, but something is up with my computer, it connects fine wirelessly to the modem, it just doesn't have a proper internet connection.I'm running windows 7, the modem is an Arris TG862.
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
What I learned was it was bad to connect directly to the modem because you are left open to the internet. Currently my friend just got the internet and I told them to buy a router but they did not, and just have it directly connected to the modem. Is this fine, because they only have one computer, and it works fine for now, but wouldn't this be prone for attack?
I would like my dcs-930l ip camera to be directly connected to my d-link dsl-321b modem (which has only one rj45 port to connect to), so that I can either access the cam via the internet (watching livestream through webinterface, that would be option 1) or so that the cam sends an email with a picture as soon as the motion sensors activate - that would be option 2 (by the way: the modem / cam get internet access through german telekom / t-online).
I have tried to get option 1 as well as option 2 to work, but I failed... I would be happy if either option 1 or 2 would work for me - I don't really care which one. In both cases, the problem seems to be that the dcs-930l cam cannot access the internet (but the cam itself works - I can view the livestream through the local network).
I have an arris modem from the ISP company and it works good, bat it is NO wireless model. So I have purchased arris WITH the wireless capability myself and ISP refused to support it so my guess that I need somehow to clone their old modem to my new one.
Today I got a new modem brought from Insight my ISP.
Modem: Arris TG862 Router: Cisco Linksys E1200
What happened is I connected to the modem's configuration page and turned off dhcp for all of the options because I wanted my router to do this, but after doing this and saving my settings, I can no longer connect to the internet or the modem no matter what I try. I really don't want to call insight when they just brought the modem.
I got a new modem from the cable company Arris TG862G. This is a wireless modem and I had them set everything up on their end which is now after 2 hours with them on the phone working fine. The problem I'm having is somewhere in my computer is my guess and their guys didn't know which way was up so i gave up on them fixing my issue. So here I am. I have a custom built computer that is using a Gigabyte mobo and has been working fine with the on board Ethernet card before now. I used to have the desktop plugged into an Arris modem via a Belkin router and this set up worked fine. I also took the current modem and plugged it into the Belkin N600 router and then to my computer and to my complete bewilderment it worked fine. I wanted to get rid of the router so I could see if I could get faster download speeds (That initial issue being on speed tests I get 50mb/s and on actual downloads I would only get 5mb/s).
I got it to work (I have no idea how) for about 20 minuets. When I restarted the computer it stopped working. I am now back to square one which is the desktop not even recognizing that there is a cord plugged in. I know the cord is fine and the ports are fine as well that isn't the issue. My laptop connected just fine to the Ethernet cord with no issue. I have uninstalled the Belkin software to see if that was the issue and no change. Everything wireless works just fine, it is just this Ethernet connection that is FUBARed, and again ONLY with the desktop.I am running Windows 7 ultimate. I am about to QQ and just deal with the 5mb/s downlods because that's not terrible but I got greedy.I was messing with the Ethernet wire some and it started picking up the router but never tried to connect to the internet, I'm going to try other wires but I don't think that's the issue.
OK so another update ladies and gents: my desktop has been on for about 40 minuets now and it is connected to the modem. I have done nothing to it that would cause this and it just randomly happened. Short of never turning my computer off again which would be hell on my power bill what can I do to fix this problem? On speedtest.net I'm only getting 30.48 Mb/s and as I said earlier I should be getting around 50mb/s (which is what I get on on the wireless laptop). I just restarted it and it wouldn't connect to the modem again.
First of all, this is how my connection looks like:
PC & Xbox 360 -> Router (Linksys WRT54GL with DD-WRT firmware) -> Modem (Arris TM602B) Everything is working just fine, except for every now and then (sometimes a few times per day), when my modem decides to "stop working" for a second or two. I do not know if it is exactly the modem, but i guess that it is.
What happens, is that for a second or two, all the lights on modem stop blinking or turns off, except "Power", "DS" and "US". Those lights stays turned on. After a second or two, all the lights continues working normally.
It would not even be that big of an issue, as i would not mind if my internet radio has stopped working for a second or if i had to wait a second before continuing with browsing the web, but it becomes an annoying issue, while i am playing video games on Xbox Live. This is what causes me to disconnect from an online game, even though, everything works normally after - until it happens again.
I am trying to figure out whats wrong with my parents apple airport router. Its connected into an Arris TM402P/110 cable modem. It randomly stops working, the network is there and shows up fine but you cant connect to it. It might work for a day or 2 and then just stops. I am trying to figure out if there is a configuration issue or the airport hardware is just failing. I am not sure where to start troubleshooting. The event log for the modem isnt much help, the following message shows up occasionally:
No Ranging Response received - T3 time-out
Whats interesting is my mom plugged her desktop right into the cable modem and then after plugging it back into the airport the wireless was working again. Is it possible there is a DHCP issue? If the hardware is failing what would be a good replacement for the airport?
I have an ARRIS Docsys3 modem from Comcast which has a built in WiFi router. I also have a DIR-655. The Modem is in my office and I have a 100' Ethernet cable running through my attic to my front room where the dir-655 is located.
I use the DIR for WiFi as well I have it connected to my TV and Xbox.I use the ARRIS Modem for WiFi as well I have it connected to another Xbox and a Desktop computer.I want to have everything on 1 network, Dir-655 uses IP address 192.168.0.1-100 and the ARRIS uses ranges 10.0.0.1-100. I want to be able to connect to the dir-655 and have the IP for that connection join up with the 10.0.0... network so that I will be able to transfer files freely throughout the network.
I want everything on one network. Right now when I connect a laptop to the DIR-655, I can not access the printer that is connected to the Desktop on the ARRIS modem. I have to connect to the ARRIS modems WiFi to then use the printer on the desktop.Likewise, I want to use the media extender on the Xbox connected to the DIR-655 with the Desktop connected the the ARRIS modem, but I can not because of the to different networks.
I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.
i have an ARRIS TM822 cable modem provided by comcast, in addition i have a linksys e3000 wireless router. what i am trying to accomplish is to bridge the cable modem over to the router. i messaged comcast about this issue and i have attempted what they told me to do, but im not getting any where.
I have a new inspiron 15 laptop and also bought an all in one wireless printer. I have a iinet BOB lite modem. I cannot for the life of me figure out how to get the wireless printer, modem and laptop to tall to one another. Am I missing something or should it all work? The laptop has internet access. The laptop also shows the printer installed with a big green tick next to it but it says it is offline. At no point has a green light appeared on the printer to indicate any wireless connectivity to the modem.
I am having a problem with my newly purchased Linksys E1000 router, I am having terribly slow network speeds while on that network.
Here are my network speeds with The e1000: (wireless) And here are the speeds with my old wrt54g: (Wireless) Here are the results directly hooked up to the modem: (wired)
I've tried setting the MTU to 1500, did a RMA with Linksys to see if it was a hardware problem, did a firmware update to the e1000, disabled DHCP and SPI, reseted my router and my modem....none of those things have worked
I just want to connect two computers over the internet as if they are in the same network. This doesnt have to be VPN I dont care about security I just want to get them connected as if they are on the same network. Is there anyway to set this up in my linksys router? Can I use windows VPN? What is the easiest way to get this accomplished? Can you somehow connect two routers through internet like one is 192.168.1.1 and one is 192.168.2.1?Like I said I dont really care how it is done I just need it done. Any easiest way to connect two computers through internet so that they are on the same network.
I think our brand new Belkin router toasted itself after it automatically updated it's firmware. We've had it for three days the first two days we were downloading around 2MB/s, then last night it updated itself and since then it's been crawling around 100kb/s.
I've tried to plug the desktop right into the modem to see if it'd speed back up but it won't give it internet access this way. I've tried rebooting the modem after and before switching cables around but nothing will make it change.
I have a problem, my netbook eMD355 is not connecting directly to our wifi. I tried to restore the system but still it doesn't connect. My windows here is WINDOWS 7 ultimate.
I've got VPN connection from Cisco 877 to ASA 5520 and on the Cisco 877 I've got SIP device which doesn't has to go through VPN. I assume that for the best audio quality I should bypass the VPN and connect directly to the SIP servers, but how to configure it??
was wondering if i go wired but through the router is it still being effected by the extra step or is that only going to effect wireless? asking because my wife is wireless but barely gets on, so if im about to do something intensive online would it be worth bypassing the router and plugging straight into the modem
I want to buy a wireless router to which I can connect my USB internet device directly, so I don't have to turn on my PC all the time if I just want to use my moble phone or iPOD or other family members wanting to connect to internet.
So I recently just built a new pc for gaming, I can't seem to connect to the internet through my router or directly through my modem. I have connected directly on my laptop and it works and through router and it works.
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
I've been using D-Link DIR-600 wireless router for two months with my ISP, SmartBro. A week ago my internet went down due to heavy rain and technical support had a home visit yesterday to re-activate my internet connection. My net connection came back smoothly using a direct connection from modem to laptop.When I tried to connect the modem to my wifi router, the internet was not detected. Even if I reset the router settings, no internet connection was detected. Initially, I thought there is a problem with my wifi router so I connected the modem to our Edimax wired router but still it could not detect internet access. Every time I open a browser while connected to a router, this message is shown (see attached screenshot).
I tried using another ISP, Wi-Tribe with both wired and wifi routers and everything worked well. So now I assume the problem lies with my SmartBro ISP. I called the ISP hotline but they told me that they do not provide support for router connection problems; only with single, direct connect to a PC.I asked a neighbor IT technician to look into my problem but he too could not solve the problem.
I have a Netgear WNDR3700v2 that I was very happy with until I got a nest thermostat. Apparently it is an unsupported router and I had to change it. I bought a E2700 since it was supported, but I'm having a huge dilemma...
If I connect the linksys directly to the modem, I'm not getting an internet connection. I've released and renewed IPs to no avail..
but if I hardwire the linksys to the netgear, I do get a good solid internet connection. problem is, I have no need for 2 routers setup on top of each other.
basically, I dont understand why linksys is not able to connect directly to the modem. yet it gets solid connection hardwired through another router.
I'm using Comcast and in south FL. it's a motorola surfboard modem
I have been using my DIR-655 for about 2 weeks now with Road Runner wideband services. Starting yesterday my internet became very slow and I discovered the cause was the router. I tried resetting it to factory settings and things will be fine and run smoothly for about 5-15 minutes but after that it goes back to being extremely slow. My speed tests would go from 10ms (normal) to 250-450ms. Before this issue occurred the Dlink was perfect, had full speeds. I am running a wire Ethernet connection.
I am currently using revB and tried upgrading firmware to 2.01NA which had no effect, but make my internet seemingly go back to normal for the first few minutes then nosedive again. I have also changed my speed/duplex settings in Network Config to 1gbs Full Duplex. I've also disabled QoS, and still no change. Not sure what else to do. When directly connected to the modem everything seems fine. The modem is also the provided Motorola SBG6580 which I have called Time Warner to set the modem into bridge mode and have the DIR-655 connected to it.
I have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
I have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
