Cisco :: Slow Ping On 2950?
Mar 15, 2013
in the last days i'm encountering some issue about ping on some 2950 access layer.These ones are directly connect (fiber trunk) to 4500 core switches. Ping response is very high between 200 up to 600 ms for a period about 30-40 seconds, then returns to normal valueI tried to ping every host connected to this 2950 and ping responses are normal 1ms or less.
View 7 Replies
ADVERTISEMENT
Feb 11, 2012
I've connected a dslmodem/router to a fast ethernet port(fa0/1) on a 2620 router.There is a 2950 switch connected to the other port (fa0/0).I can ping the Internet via the router but and the switch but not from a host connected to the switch.I can't reach the dslmodem from the host pc.I've configured nat(overload) on the router.
View 8 Replies
View Related
Apr 15, 2013
I have been though the setup a couple of time with no luck pinging one pc to another from vlan 10 to vlan 20. I posted the running configs and some other information from my router and switch. I am relatively new to all of this so if you need me to post more information from the hardware let me know and Ill put it up. There are no firewalls in place and I know the cables are good because I switched them around to make sure. Also when I change the ip on my second machine for vlan 10 I can ping from one pc to the other but when I try the same for vlan 20 I get nothing.
**From my 2950 switch**
Current configuration : 2825 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
[code]...
View 5 Replies
View Related
Oct 1, 2012
My customer has various Cisco switches but only cisco 2950 switches has the problem of ping timeout or reply time is too long(average more than 2 sec). It will cause I Network Mangement software alarm always.
View 4 Replies
View Related
Jan 31, 2012
Our network feels slow and trying to find the best way to investigate this properly. We have Cisco chassis 4500 with mix of 3560/2950 Edge switches 1GB backbones and WLC/WCS in place. The network is broken into multiple V LANS and IOS on our switches haven't been updated in 3-4 years.
On a wireless laptop (G) with get throughput of 1-2MB/s transfer speed with usually 10 clients per AP and LAN we get anywhere between 7-15 MB/s transfer. Using wire shark on a wireless laptop we see a lot broadcast traffic from other clients and the same for LAN. What is the best way to troubleshoot performance issues on the network and where do I start?
View 1 Replies
View Related
Mar 7, 2012
My wireless connection says i have full bars of signal. When I do a speed test, i get 500-600 kb/s download. Which is what I used to get. However, after I re-installed my wireless adapter's card, the wna3100 netgear, it became extremely slow.
Pages would load slow, I could no longer play League of Legends properly because the ping is too high. Also, I used to have crossfire graphics cards running and the internet was fine, but after reinstallation, I thought I'd turn it off because that's how I fixed it before. But now, even with just one graphics card running, the internet is extremely slow.
[code]...
View 14 Replies
View Related
Jan 17, 2012
slow ping times with Realtek, no problems with intel
View 1 Replies
View Related
Feb 21, 2011
A while ago internet access was slowed right down for an hour or so. I have a phone line that comes into the house and then into gateway (10.0.0.2) then ethernet from that to linksys wifi router (192.168.1.1). So I did the following ping and repeated what you see below a few times to see that these results were broadly consistent, which was the case. One other person is connected to linksys via ethernet cord and they might have been on at the time. Questions are.... are these results consistent with contention caused by other user on the linksys? and why can I ping gateway but not the router? That makes no sense to me! I am not annoyed with the other person if he is hogging the network...I like him. I just wonder whats going on. When the internet works results from pinging are all as one would expect
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsNASA>ping 192.168.1.1
[Code].....
View 4 Replies
View Related
Aug 18, 2007
I have installed a WRT300N on to a new machine and the connection speed reads as 1 Mbps (not 100 but 1 ). I did a ping test and the results are
View 2 Replies
View Related
Nov 9, 2012
Each time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies
View Related
Jan 2, 2012
I bought router WAG160n half year ago. At the begining router worked ok but now I have a problem. Sometimes my Internet slow down. When Internet works bad I have problem with open router websites and when I send ping to router I have very bad answer like 300-2000 ms (distance router to computer 3 meters). Than I restart router and everything is ok. Aha, Internet with cable works ok everytime.I have problem when I send big file to another computer with Wi-Fi
View 4 Replies
View Related
Apr 9, 2011
I have a gaming machine i ran for some time on a wireless connection. This connection had decent speeds but was unreliable and at times very slow (3000 vent ping). So me and my father fished some cat5e cable through some wall from our router to my room. We used some old external jacks verizon gave us and some 6 foot patch cables to connect the computer and router to the jacks. My problem is that once it wall all connected the lan speed has been terribly slow (several times slower than the wireless). Previously I used an ASUS pce-n13 wireless adapter and now the lan is running of the nvidia nforce on my Asus P5n-d motherboard. I am clueless to the problem and I have called Verizon and gotten nowhere.
View 3 Replies
View Related
Aug 16, 2012
I purchased the AE3000 Wireless Adapter for my PC, and has been working fine until now. When I first start my PC, my ping starts anywhere between 20-80, then after I try to access anything on the internet it shoots up between 600-1200. It just started happening about 3 days ago, but now it has gotten worse. I can't play any online games, and websites are slow to load.
View 1 Replies
View Related
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
Dec 12, 2011
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
Aug 15, 2011
When I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
View 1 Replies
View Related
Jan 26, 2012
I installed window server 2003 in a old Pentium III server as a standalone test server. Now I want to use it as a print server and connected it to the domain. I can ping workstations and other servers from that test svr. But i cannot ping that test server from the work stations.
View 2 Replies
View Related
Sep 28, 2011
We have installed last Network Assistant version, 5.6(3), but we can't add any switch to it.... It says always "Unsopported Device type: unknown".Our switches are all 2950, 2960 and 2970 models.
View 4 Replies
View Related
Oct 6, 2011
Telco provided a BGP connection on MPLS network. When I connect router directly to Telco switch I can see BGP neighbor, so my router BGP config is OK. However, I need to put this router in a diffferent building and want to bring the connection over on a "trunk"; now I loose the BGP neighbor. I'm sure I did this before and it worked OK. I'm trunking between 2 x2950 switches using this config on each switch. [code]
I also configured the trunk as vlan 1214, which is the encapsulation provided by the Telco (dot1Q 1214).
View 6 Replies
View Related
Jan 2, 2013
Is it possible to run VTP V3 on 2950 and 2960 switches. If so what version of IOS supports V3? Our 2960s are running 12.2(25r)SEE1, and 2950s are running 12.1(22)EA4a. Neither of which supports v3.
View 3 Replies
View Related
Mar 13, 2008
I have a catalyst 2950 ver. 12.1 EA(48 SI) and intend to upgrade to the latest version of the software. But there have been Four different IOS IMAGE releases before the latest one of 2008. My question is, DO I HAVE TO UPGRADE THE PREVIOUS FOUR RELEASES BEFORE THE NEW ONE OR WILL UPGRADING DIRECTLY TO THE 2008 NEW IMAGE Suffice?
View 2 Replies
View Related
Mar 1, 2013
I had both a Westell 7500 and a Linksys Router working fine and had my 360 setup as an extender for Windows Media Center so I could stream TV, Music, Movies, etc from my desktop to the 360. Then I switched my modem/router out with a Zyxel PH5001Z
So now today I noticed that I can no longer find my desktop through the XBox. I have adjusted my firewall settings on the modem itself, even completely disabling it. UPnP is enabled for the 360 and the device is showing under my device table. At first I wasn't able to ping any network devices but after creating an ICMPv4 Firewall rule it worked fine. I've confirmed the XBox IP Address through Network Map, the Device Table on the modem and through Network Settings on the XBox. I've diabled my modem firewall as well as Windows Firewall, completely and I still can't ping my XBox or set it up as an Extender.
I have the XBox connected wirelessly using WPA2-Personal and it's operating in 802.11g/n mode.
View 19 Replies
View Related
Jan 10, 2013
Im looking to connect up 4 new pcs to network but I don't have enough wall ports. I thought I could plug cisco 2950 switch into the port on the wall and act like a hub. The switch configuration is default and there is only one vlan. How is it that it won't connect. Does it need a crossover cable.
View 3 Replies
View Related
Feb 7, 2011
I am trying to figure out how to setup quality of service on my network. At the moment i have computers connected to the PC port of my IP phone and the IP phone connected to the switch.I want the PC to stay on the default native VLAN and the phone to go on the VLAN 10I am using SNOM300 and SNOM360. I will configure the on the phone the VLAN ID and the priority.From my research, there are two ways that I can go about this on the port that is connected to the phone I canswitchport voice vlan vlan-idorswitchport voice vlan dot1pand then I will have to execute the commandmls qos trust cosmy question is which command do i use to configure the ports, and am I on the right track? Also, this is how I configure the ports that the IP phones are connected to, how do I configure the port that my Asterisk PBX server is connected to?
View 4 Replies
View Related
Nov 13, 2012
What is the difference between the 2950 and 2950c switches? I tried finding it on the feature navigator but I couldn't. And I wasn't able to get anything from the Cisco website either. (I didn't really look through the long PDFs, I'm sure there is a more simple way to find the answer to this that I'm not aware of.)
View 3 Replies
View Related
Aug 3, 2012
I need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
View 1 Replies
View Related
Apr 9, 2013
Bought a used 2950 for CCNA labs. I have no IOS and cannot get a successful transfer via xmodem. In ROMmon after the transfer completes text shows up as gibberish, commands seem to work. Text is normal after I reconnect. Dir flash: doesn't show any sys image, only a -rwx file. I have tried various IOS versions. This was purchased used, so it's possible it isn't working. This is my first time configuring a switch, I might have missed something simple.
View 5 Replies
View Related
Feb 23, 2006
how to enable RSTP in the switch (Let's say in 2950 switch).
Or do you have RSTP running in now-a-days switches?
View 2 Replies
View Related
Dec 27, 2010
I just started configuring my cisco catalyst 2950 switch. Basically im preparing for my CCENT exams my basic configuration is as follows.
-My Laptop is connected to the console port
-I'm connected to the internet via my wireless
-I'm connected to the switch port via my NIC card
View 4 Replies
View Related
Feb 16, 2011
I need to update the software for the switch 2950 we have in our LAN. Its been 6 long years I have not looked at this switch and so now is the time since I have had some issue (ie. Outlook losing connections and once in a while email get send out AGAIN for bazzarre reason)
Anyways, I am looking here for thes software I am abit unsure which software to use via Network Assistant. This is the current status of the switch (Cisco 2950, WS-C2950T-SI, 12.1(22)EA4a - C2950 - I6Q4L2-M ). I want to understand what is the difference between C2950 EI AND SI IOS CRYPTO and web based device manager and C2950 EI AND SI IOS IMAGE AND WEB BASED DEVICE MANAGER and which one should I be using for my switch?
View 2 Replies
View Related
May 6, 2012
We are in a process to replace our old end of life switches( mostly Cisco 2950's) with some new offerings from cisco. Attached is our current network diagram. Anny merit of using Cisco Nexus switches in this design and also what will be the benifit in doing so. Again I am asking about the specific benefits which I will get in my Network not general benifits of nexus.
View 5 Replies
View Related
Dec 7, 2011
I have a etherchannel defined between 2 L2 switches using LACP as shown below. The etherchannel works fine, however when I hard code speed/duplex on both ends the etherchannel fails. What is causing this behaviour?
SW02:
interface Port-channel5
interface GigabitEthernet1/0/1
switchport mode trunk
[Code]....
View 6 Replies
View Related