Can't Ping XBox 360 But Can Ping Other Devices
Mar 1, 2013
I had both a Westell 7500 and a Linksys Router working fine and had my 360 setup as an extender for Windows Media Center so I could stream TV, Music, Movies, etc from my desktop to the 360. Then I switched my modem/router out with a Zyxel PH5001Z
So now today I noticed that I can no longer find my desktop through the XBox. I have adjusted my firewall settings on the modem itself, even completely disabling it. UPnP is enabled for the 360 and the device is showing under my device table. At first I wasn't able to ping any network devices but after creating an ICMPv4 Firewall rule it worked fine. I've confirmed the XBox IP Address through Network Map, the Device Table on the modem and through Network Settings on the XBox. I've diabled my modem firewall as well as Windows Firewall, completely and I still can't ping my XBox or set it up as an Extender.
I have the XBox connected wirelessly using WPA2-Personal and it's operating in 802.11g/n mode.
View 19 Replies
ADVERTISEMENT
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
Sep 27, 2012
I have 4 x 2960 switches in a remote site. These are managed by an NMS in our DC, the NMS IP ends in 35.100 with a /23 mask.
When they are first booted, the switches are visable to the NMS, but after a week or 2, 3 of them drop connection to it. If you reboot them again they are fine. You are able to log onto them form thier local router and use a Radius server which is in the same subnet as the NMS.
The odd thing is, whilst they can not ping the NMS, they are able to ping any other addresses in the 34.0/23 range.
The config on the one that does not lose connection is the same as the other 3 and I have also rebooted the NMS.
View 3 Replies
View Related
Sep 18, 2011
I have a copper over ethernet connected to an adtran 908e connected to an ASA 5505 with a port 192.168.150.254 connected to the router on the Gigabitethernet 0/0
I can ping to internal and external ip addresses but when a device is connected through the wireless signal then the device cannot ping anything; what could be stopping the device from pinging any ip addresses internal and external?
I posted my current config for the router and ap:
Router:
Current configuration : 2245 bytes
!
! Last configuration change at 16:03:06 UTC Tue Sep 6 2011
[Code].....
View 1 Replies
View Related
Mar 28, 2013
I'm trying to configure a 2800 series router. .I'm consoled in and put a basic config on the router (see attached). After putting this basic config on, I plugged it into a small unmanaged switch, changed my laptop's IP and plugged it in the switch also. I can't ping the router from the laptop and vice versa. This is the second switch I've tried this with, so it must be.The first switch, I installed at location, connected a cisco cable to it and a local server, so i could remote in and finish configuration. In that scenario, I had plugged the switch into a managed switch and had the same result as I'm getting now--can't ping IP addresses (can't ping the switch's IP, not can it ping local IPs).
View 2 Replies
View Related
Mar 5, 2012
I have several cabinets with top-of-rack N2K's attached to N5K's via FEX's. 9 cabinets with 2 switches each.
Recently I added 3 more cabinets to the mix, for a total of 12 cabinets with 2 switches each.
I can get into the new switches and see the FEX's and configure ports, etc. but no device I attach to the 'new' N2K's is pingable over the network. I can take the same device, same cable, and attach it to a legacy N2K talking to the same N5K's, and it immediately joins and is pingable over the network
View 2 Replies
View Related
May 25, 2013
vrf ping is not happening between two pe devices in 7609 router having VS-S-2T-10G modules with 15.1 SY1 IOS version? Is there any commands need to add? between pe devides ldp is running properly and ibgp too. I am doubtful about VS-S-2T module.
View 2 Replies
View Related
Dec 12, 2011
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
Aug 15, 2011
When I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
View 1 Replies
View Related
Sep 4, 2011
I have a DLink wireless bridge connected to the wireless WRV210 router. All devices connected to DLink can access internet/email fine and can ping the WRV210, however, they can not ping any device connected to the WRV210 router, nor can any device on the WRV210 ping devices on the DLink writeless bridge. All devices are on the same subnet, 192,168.100.X with mask 255.255.255.0. All devices get their address from the WRV210.
View 7 Replies
View Related
Feb 11, 2013
I have a Cisco 871 router and I have successfully added a second vlan and connected a switch configured with that VLAN. Anyways, my problem is the device in my new VLAN (vlan200) are able to ping/access devices on vlan1. I do not want this to happen. I read somewhere that the 871 routes between VLAN's by default.
View 3 Replies
View Related
Jun 11, 2012
We have configured a Cisco ASA 5505 with AnyConnect access. This works great. However, these users cannot seem to ping devices on the private network. We have configured all devices on the network with a 10.10.10.0/24 address space. The inside interface of the ASA i 10.10.10.1/24 and the VPN return addresses are 10.10.10.50 - 10.10.10.65/24.They users can utilize SSH and Oracle or MySQL calls but cannot seem to ping. Obviously, I am over looking something.
View 2 Replies
View Related
Jan 26, 2012
I installed window server 2003 in a old Pentium III server as a standalone test server. Now I want to use it as a print server and connected it to the domain. I can ping workstations and other servers from that test svr. But i cannot ping that test server from the work stations.
View 2 Replies
View Related
Feb 7, 2013
I wounder if there is any way to ping the local deviceses connected to a network hosted by a Cisco 1921 router? I wan't to be able to ping the device(computer name) but currently cant do that.
View 1 Replies
View Related
Feb 29, 2012
I have a strange issue on my ASA 5510 (8.4). I can't ping or connect to the VPN clients but the VPN clients can ping/connect to any inside resources. I have checked all the NAT extemtion entries.
View 3 Replies
View Related
Sep 14, 2012
At home, my current setup is:
1. Motorola SBV5220 Surfboard Cable Modem for internet
2. Rosewill 8 Port Switch RC-406X
And I have:
1. Dell Q6600 desktop running on Windows 7
2. Dell Latitude laptop running on Windows XP
3. Xbox 360
These all need access to the internet.Up until now, everything worked fine. The Motorola modem was connected in Slot 1 and my desktop, laptop and Xbox were all 3 connected into slots 2, 3 and 4.The other day, I accidentally pressed a switch in my home that switched off my modem. Anyway, once everything was reset, things changed.I can no longer be on the internet with all 3 devices at the same time. Either only the laptop can be connected, with the 2 other devices being offline, or just the desktop and not the laptop.Whenever I gain access to the internet via the desktop, it shows as Network 10 and if I try and repair the connection on the laptop, it says it is unable to renew the IP address. If I switch it up and I have access on my laptop but try and have access on the desktop, the network shows up as Unidentified.
View 4 Replies
View Related
Sep 29, 2011
Been racking my brains out for hours now, my remote access VPN via Cisco VPN Client is UP i can ping the RA VPN DG but cant get no further than that relevant config below i can ping 192.168.250.1 and it replies with the public ip address, but i cant ping any 192.168.101.* addresses.
View 1 Replies
View Related
Aug 11, 2011
Im having some Ping / MS issues lately. My ping bounce up and down from 30 to 600 in just some seconds, and its really unstable. Im using the same internet as my neightbour ( internet cable through the wall) Is there any1 who can give me some tips so I don't need to worry about my ping anymore?,I don't know much about he's internet though.
View 3 Replies
View Related
Sep 27, 2011
I Have 15 computer and they all are in Internet Connection.And I Have Network of C class that is 192.168.5.11.But the main Problem is that the computer are not getting ping with each other.How can I get them Pinging between them.Can any antivirus stop them?
View 1 Replies
View Related
Jun 27, 2012
I have Windows 7 x64 on my desktop, laptop, and HTPC. The past few months, everything worked fine. Today, I can ping my IP address but I cannot ping the host name on all 3.They also do not show anything in the network window, just the computer that I'm on.
View 1 Replies
View Related
Dec 23, 2011
I'm using xp pro. Sharing is enabled. No firewall. I can ping between both pcs. I've run the network wizard on both pcs. I can only share one way. The other gets the error don't have permission.
View 7 Replies
View Related
May 24, 2012
I installed the GFI Webmonitor proxy on my network. Previously my ping was 83ms now it can get up to 2500ms. Is there anyway to reduce this?
View 3 Replies
View Related
Apr 16, 2013
I used to access my NAS by typing "\mydrive" in the folder path. But after I have added computers into my local network, some computers became failed to access the NAS (it shows that it cannot find the specific location). I can still ping the NAS IP and also other computers in the network.
View 3 Replies
View Related
Nov 11, 2012
I have a Q1000 and I'd like to be able to "ping yahoo.com" (etc) once in a while when I think there may be a network problem. From my desktop I type > ping yahoo.com and nothing happens. I can ping other device on my LAN but the only way to ping somewhere outside is to http://myrouter -> Utils -> Ping test.
View 4 Replies
View Related
Oct 29, 2012
I am wondering how I can attain a higher ping...
First my specs:
I have DSL, with the modem my ISP has provided me with..
I have a belkin wireless G router (which I want to upgrade to a Dlink wireless N 815, as soon as I can hook it up)
My ethernet adapter is intregated into my mobo, which is a ASUS P5K motherboard, with 10/100/1000mbps ethernet.
I am wondering what I can do to get a better ping?
The best ping I have ever had (on an idle system) is 25ms.
is there anything I can do to get a better ping?
(also, I live within 100km of large city centers. I do not live out in the middle of nowhere)
View 2 Replies
View Related
Feb 10, 2013
I'm really lost with this issue. its been going on for months. here is a copy paste of my ping to yahoo. "ping yahoo.com -t"
View 1 Replies
View Related
Jan 12, 2011
This started out as a printer issue and then evolved into a networking issue.let's see if i can include all the details here. the laptop in question is having problems talking to other internal network computers/printers. i am on a 192.168.10.? network, the laptop has a dhcp assigned address, my domain controller/dns/dhcp server has an address of .3, i have a fileserver at .9, my default gateway is .1 the laptop can ping all 3 of those computers.i have a printer with .130 address, the laptop times out when pinging it. there are around 15 or 20 other computers on the network with dhcp assigned addresses.so far i cannot get the laptop to ping any of those.
The same thing happens whether i am connect using the Local Area connection or wireless, so 2 different NICs, same laptop though.the laptop can ping any outside address, the firewall is turned off, the other computers that i cannot ping can ping each other and the printer. here's the real kicker, i noticed while running ping 192.168.10.130 -t when i do a repair on the network connection, the darn thing will ping the 130 address 3 times then start timing out again? is going on? i have killed every weird ass service i can think of, i have booted up in safemode with networking with the same result. i have signed in as a different user, i have looked at the routing, the host file, nothing looks weird to me at all. i have also run the winsock fix for xp......
View 5 Replies
View Related
Oct 12, 2011
i can't get my ping of client ip.
View 1 Replies
View Related
Sep 24, 2012
2 windows 7 machines.at work..They are both laptops. one acts as a server for a piece of software to the other one.on the "client" laptop I can map a drive to the "server" and browse files through that maped drive etc.I can also ping the IP address of the "server" but I get a timed out when I try to ping the computer name.Server had Macafee firewall, I uninstalled that, and I turned off Windows firewall on both machines.the software needs to be able to ping by name I guess in order to work..
View 2 Replies
View Related
Oct 7, 2011
i want to know how to reduce my ping while playing counter strike condition zero online ??
View 1 Replies
View Related
Jan 19, 2011
We've got about 15pcs at work, all on one network. All connect to one switch, and the router connects to the switch so all has internet access. Four pcs has got windows vista on, the rest XP. Yesterday I tuned on the one pc with Vista on, but could not connect to a mapped drive. I checked in the network places, i could see only three pcs, all three xp pcs. I can browse the internet, but not the pcs on my local network, and I can ping the pcs on the network.
View 1 Replies
View Related
Jul 27, 2011
Ok, I have a ASA 8.4 firewall that I have been working on so long. It was a hassle to configure the object group and nat for 8.4. So, I put two host in both side of ASA to test pinging but I can not ping the outside or the DMZ. I attached my nat config.
View 1 Replies
View Related
