I used to access my NAS by typing "\mydrive" in the folder path. But after I have added computers into my local network, some computers became failed to access the NAS (it shows that it cannot find the specific location). I can still ping the NAS IP and also other computers in the network.
View 3 RepliesI have a site-to-site VPN (no client software) that is up and I can ping all the IPs on the other side.
My computer is connected to .2.0, remote LAN is .1.0
I can view all of the local LAN (.2.0) devices in Network Location, but can't access the shared resources on the remote .1.0 LAN.
ServerFolder shared directories is mapped as a drive and worked yesterday. It now has a red X on in and I can't access it, but can ping \Server's IP address.
I recently bought a new DLink 615 E4 router.After a botched firmware update, I attempted to enter the emergency room.I got in once, and tried to upload the firmware using Internet Explorer 8, but it was stuck there for over two hours without any progress (stuck at the browse/upload page), so I disconnected it.
I haven't been able to enter the Emergency room since then. I get to the point where the power light blinks orange, and connecting my laptop to the router using the wired connection lights up the proper LAN light, but I cannot ping or access 192.168.0.1 anymore.
I was able to go onto the internet with no problem. I've been searching forums trying to solve my problem but to no avail. I have Windows XP installed, I can connect to the LAN network but I cannot go online. I can ping the gateway but not the DNS as well as other address name or ip address. This is the output of ipconfig /all:
Description : Realtek RTL8139/810x Family Fast Ethernet NIC
Dhcp Enabled : Yes
Autoconfiguration enabled: Yes
IP address: 192.168.1.145
Subnet mask: 255.255.255.0
Default Gateway : 192.168.1.1
DHCP Server : 192.168.1.1
DNS Servers : 202.160.8.2
202.160.6.20P.s: All the other computers in the LAN can connect to the internet.
I have a home network of 3 cmputers. DHCP from router. 1 computer is not getting address. But if I assign it one, with same gateway and dns(not a duplicate ip of others), it can ping internally, and outside. I can do tracert to 8.8.8.8 and ping it (google DNS). But I can't get to internet. So - i can get out, but nothing coming in. I have checked firewall.
View 4 Replies View RelatedRemote access VPN. Its configured on a Cisco PIX525 running ver 6.3(5) (old I know!) and I am running Cisco VPN client ver 5.06.0160 on the client end. Ok so here's the thing. The client connects ok, and it gets an IP address no problem. But I cannot ping anything on the remote LAN. So the client is coming across the internet, the VPN adapter has a 192.168.1.1 address assigned by the PIX and I am trying to ping the 192.168.0.4 address assigned to a switch on the inside of the firewall but with no joy. [code]
View 1 Replies View RelatedI'm trying to setup my home network so that I can access it when away from home but I've ran into problems and I can't figure out what is causing the problem.I've setup the router to forward incoming requests on port 80 to be directed to my PC running WAMP. The PC has a static IP and if I access it from another PC on my network I get the WAMP page load as expected.I've also setup an account with no-ip.com to resolve my (dynamic) ip. If I use the address they have setup while I'm on my network I get the login page for the router, again this is what I expect.The problem begins when I try and access my home address (whatever.no-ip.biz) from outside my network. I've tried it from 2 different locations and via a dial-up account and I get nothing.
View 6 Replies View RelatedIt works on the mobile site at times maybe twice a day but only able to access for 10 minutes maximum. I tried the command prompt and ping facebookm and noticed that I didnt recieve files back and it was just timing out is that whats causing it?
View 3 Replies View RelatedI have a Linksys e4200 and a EnGenius EAP300. I setup new EnGenius AP to 198.162.1.5 and the Linksys is 198.162.1.1. The two devices are connected with Ethernet capble with a POE switch in the middle. Internet connection thru the Linksys works fine. However, the EnGenius does not connect to the Ineternet (Gateway is set to 198.162.1.1) Also when connected to the Linksys, I cannot ping the EnGenius.
View 1 Replies View RelatedI have a ASA 5505.|I configured it for remote access VPN from cisco VPN client.the ASA receives a public ip address on outside interface via PPPoE.I can connect to public ip of outside interface and address 10.1.1.2 is assigned to my Cisco vpn client.the problem is that I Cannot ping or reach ASA internal IP address 172.16.29.1 in any way when I am in VPN from outside,while I Can ping other hosts on 172.16.29.0/24 when connected in VPN.this is a problem brcause when I am connected in VPN to ASA I Cannot configure it..Then I Wanted to ask if it is possible a configuration which gives addresses from network 172.16.29.0/24 (the same as inside network) to VPN clients instead of another network (10.1.1.0/24) [code]
View 1 Replies View RelatedI have a RVS4000 and I would like to setup a Ping monitoring from the outside to a device behind RVS on lan network. I have created a rule to allow a service PING for range from WAN 46.xxx.xxx.xxx - 46.xxx.xxx.xxx to host 192.xxx.xxx.xxx but unfortunately this is not working. I can confirm that I can ping host 192.xxx.xxx.xxx from diagnostics on RVS.
View 2 Replies View RelatedI am new to Cisco and am studying for my CCENT certification. At the moment, I am attempting to correctly configure a Cisco 871W lab router. Since I have undertaken this task, I have run into nothing but problems. First off it was finding that the previous owner had left a password on it, having to purchase a new USB to DB9 adapter to pass the "break" sequence to the router, and then resetting the router in ROM Monitor mode.
Now, I cannot seem to configure the router correctly, and am quite stumped.
My ISP is Charter (cable internet), and the home network that I am using consists of a Motorola SBV5122 Digital Voice Modem, Motorola SB6120 Cable modem, and, ideally, should also include my Cisco 871W router.
When I connect my router to the SB6120 Cable modem, the router receives an IP address via DHCP and the WAN indicator light turns on.
I have a VLAN configured on the 4 switchports of the router, and it is setep to act as a DHCP server. However, when I connect my PC to rhe router via Cat5e Crossover cable, I cannot access the internet. The router gives the PC an IP address, yet all attempts to ping the PC from the router fail. Somehow, I can connect to the router via SSH though.
Furthermore, I can ping the 127.0.0.1 loopback address from my PC, but cannot do so from the router.
how to correctly configure this router to function as intended in my network situation, however, this is proving to be seemingly unsurmountable!
I have attached the config of my router along with both outputs and commands relating to my predicament.
every time i try to acces my linksys router my IE just auto adds http:// and opens google search results. I cannot make IE not auto add that freaking http thing, on the old win XP i could type in 192.168.1.1 and it just went straight to my router login. Do i disable this IE auto http crap? i simply cannot acces my router anymore??i can ping the router, even using Cisco network magic pro I tried to reset router checked my internet settings everything works fine, this pc has a dhcp auto configuration etc.
View 9 Replies View RelatedI have 1 PC and 2 laptops. All are connect to the WAG160N router. All 3 can access the internet but they cannot see each other, not even by ping.I have turned my Kaperksy internet Security off and this makes no difference. Windows Firewall is turn off.
View 2 Replies View RelatedI have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these access methods worked properly for me.I believe I may have inadvertently changed something as of Friday using ASDM. I am mostly assuming this because, as of yesterday I can no longer connect to the device. I actually cannot even communicate with it (ping the interface I normally use to manage, which I could previously ping). No computer on the same subnet as me is able to ping the interface. The device is still accepting VPN connections, dishing out DHCP addresses and everything else it normally does, but I really need to be able to gain access to it again. I am thinking to reboot the device when there is some downtime, in the hopes that ASDM doesn't save to startup-config and only to running-config.
View 5 Replies View RelatedThe VPN will connect.I can ping and connect to the ASA 5510 on it's LAN interface.My problem is that I cannot ping or access anything on the LAN past the firewall. What am I doing wrong?
Here is my config.Result of the command: "show config"
Saved
: Written by enable_15 at 22:55:02.299 UTC Tue Jan 10 2012
!
ASA Version 8.2(5)
!
hostname ********
[code]....
I'm configuring ASA 5510 Remote Access VPN, I can connect from Cisco VPN Client to the ASA VPN. I obtain from ASA some routes to inside networks, but I can't do any ping to those inside hosts. I have got those error in ASDM log file: [code]
View 1 Replies View RelatedSo I have a laptop that wont connect to the internet, my other laptop works fine using the same router.I can ping google.com and yahoo.com fine. Intel(R) PROSet/Wireless says connected but no internet. I cant use a network cable to connect either. Laptop: DELL XPS M1210, Windows XP, Service Pack 2..[code]
View 5 Replies View RelatedBasically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:SA 8.4: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http while other ports can be accessed using the original IP (10.252.253.123).
ASA 9.0: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http but unlike before now I cannot access to the original IP (10.252.253.123) using another port or ping from host 192.168.3.2.
I have setup a VPN connection on a 891 router. I can connect to the VP both but am unable to ping or access any resources on the remote network.
Here is my running configuration:
[code]...
I have easy vpn on my PIX 515e and working normally everywhere, except when my users go FRANCE, the vpn client connect, but, can't ping or access any inside network resources. when same user try any where here in EGYPT, it works normally.
View 2 Replies View RelatedI have a Cisco 871 router and I have successfully added a second vlan and connected a switch configured with that VLAN. Anyways, my problem is the device in my new VLAN (vlan200) are able to ping/access devices on vlan1. I do not want this to happen. I read somewhere that the 871 routes between VLAN's by default.
View 3 Replies View RelatedIve been struggling with this issue for a week now with an 877w (now with andvanced ip ios) in short my wireless network consists of
The internal dot11 sibinterface 0.11 radio (IP Address 10.0.1.1) which on bridge group 1 (IP Address 10.0.0.10) The SSID for the radio is on vlan 11 which has no ip address.
This works i can ping the internal network and internet
The guest dot11 sibinterface 0.10 radio (IP Address 10.0.3.1) which on bridge group 2 (IP Address 10.0.2.1) The SSID for the radio is on vlan 10 which has no ip address.
This dosnt work i get no no recived packets on the clients network stats and i cant ping any name servers or the radio ip address.The client is listed as being successfully accosated with the show dot11 assoc commmand
Ive tried taking the guest wireless and creating a new vlan for it (so its not on the same vlan as the tmg firewall interface) so that i have only the dot11 radio and vlan 12 on brige group 2 but the same thing happens no traffic on the guest vlan.
Ive turned off all authentication while testing this and the wireless network is currently in open mode until its fixed ive also only configured whats neccessry to test the wireless connectivity (no radius etc) that will be added later, Im also not using dhcp yet and the client is configured to the apporprite adderess staticly ie 10.0.1.1 10.0.3.2 its not a dhcp issue
!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!logging message-counter syslog!aaa
[Code].....
I have a cisco 5505 and am trying to configure it with ASDM 6.4.
My vpn client connects ok to the network but I am unable to reach any of the servers.
I'm sure its a simple configuration issue as I don't have much experience with Cisco configuation.
I am using the default configuration at this point. I just connected 1 computer using the default IP with DHCP on the RV042 router. 192.168.1.0/255.255.255.0.I connect my wildblue satalite modem using a static IP address 75.106.203.xxx / 255.255.252.0 I can ping the RV042 router and the static IP address of the wildblue router but I can't ping the gateway on the wildblue side. Either from the PC or the Router diag tools.
View 1 Replies View RelatedBelkin N750 Router - wired connection can not access Internet. I've tried direct to modem and have no problem, have tried old router, no problem, but if I shut down desktop completely (Win7) and restart, I get no connection. Uninstalling the NIC (Intel 82579V Giga) and restarting, then I get connection again. However, if I start in safe mode with networking, I have no problems at all. I've disabled my firewall to no avail.
View 3 Replies View RelatedI am having a problem configuring my ASA 5505 for NAT.
View 3 Replies View RelatedI would like to setup a VPN to allow employees nomad that connect to our network from outside. Our router is a Cisco SA520 I tried different configurations without success ...Here is the current VPN configuration:I created my users IPSec, I can connect remotely, but I do not have network access ... Unable to access network shares, impossible to ping.
View 1 Replies View RelatedWe have configured a Cisco ASA 5505 with AnyConnect access. This works great. However, these users cannot seem to ping devices on the private network. We have configured all devices on the network with a 10.10.10.0/24 address space. The inside interface of the ASA i 10.10.10.1/24 and the VPN return addresses are 10.10.10.50 - 10.10.10.65/24.They users can utilize SSH and Oracle or MySQL calls but cannot seem to ping. Obviously, I am over looking something.
View 2 Replies View RelatedI have a cisco 876 with, c870-adventerprisek9-mz.124-6.T9.bin. I have configured a VLAN with ID 230, an SVI with IP 192.168.230.1/24 and I have assigned switch port fa 2 to it…
interface Vlan230
ip address 192.168.230.1 255.255.255.0
VLAN ISL Id: 230
[Code]......
Connected server on a tenGigabitEthernet interface simple configuration setup
switchport
switchport access vlan 201
end
for server connection. Connected with Fibre. The interface is up and up but cannot ping server?
i have 2 RV048 and one RV016
I have established VPN gateway to gateway tunnels; all routers use functional DYNDNS
IPrange site 1 192.168.123.1-254 external adres x.y.z.w
IPrange site 2 192.168.124.1-254 external adres a.b.c.d
IPrange site 3 192.168.122.1-254 external adres e.f.g.h.i
site 1 with 192.168.123.x has two win 2008R2DC servers, running AD, DNS, DHCP, RRAS with address 192.168.123.4-5
i can ping the routers only if i add the route to it but cannot ping further (route add command)
if i dont establish the route then nothing pings
How can i use the tunnel to connect to the servers in site 1
I have a fresh out the box asa5510 with 8.4 on it.I have built these before but for some reason cannot get this one to work. I am consoled on, have applied the following config but can still not ping to or from, can not asdm, cannot http/s. Arp table shows device it tries to ping, but device trying to pping it has incomplete arp entry. [code]
View 7 Replies View Related