Cisco VPN :: Remote Access VPN On PIX 525 - Cannot Ping
Sep 13, 2011
Remote access VPN. Its configured on a Cisco PIX525 running ver 6.3(5) (old I know!) and I am running Cisco VPN client ver 5.06.0160 on the client end. Ok so here's the thing. The client connects ok, and it gets an IP address no problem. But I cannot ping anything on the remote LAN. So the client is coming across the internet, the VPN adapter has a 192.168.1.1 address assigned by the PIX and I am trying to ping the 192.168.0.4 address assigned to a switch on the inside of the firewall but with no joy. [code]
View 1 Replies
ADVERTISEMENT
Jul 28, 2011
I have a ASA 5505.|I configured it for remote access VPN from cisco VPN client.the ASA receives a public ip address on outside interface via PPPoE.I can connect to public ip of outside interface and address 10.1.1.2 is assigned to my Cisco vpn client.the problem is that I Cannot ping or reach ASA internal IP address 172.16.29.1 in any way when I am in VPN from outside,while I Can ping other hosts on 172.16.29.0/24 when connected in VPN.this is a problem brcause when I am connected in VPN to ASA I Cannot configure it..Then I Wanted to ask if it is possible a configuration which gives addresses from network 172.16.29.0/24 (the same as inside network) to VPN clients instead of another network (10.1.1.0/24) [code]
View 1 Replies
View Related
Jul 26, 2011
I'm configuring ASA 5510 Remote Access VPN, I can connect from Cisco VPN Client to the ASA VPN. I obtain from ASA some routes to inside networks, but I can't do any ping to those inside hosts. I have got those error in ASDM log file: [code]
View 1 Replies
View Related
Dec 6, 2011
I have setup a VPN connection on a 891 router. I can connect to the VP both but am unable to ping or access any resources on the remote network.
Here is my running configuration:
[code]...
View 5 Replies
View Related
Sep 19, 2012
I have a cisco 5505 and am trying to configure it with ASDM 6.4.
My vpn client connects ok to the network but I am unable to reach any of the servers.
I'm sure its a simple configuration issue as I don't have much experience with Cisco configuation.
View 5 Replies
View Related
Sep 13, 2012
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
View 1 Replies
View Related
Jun 24, 2012
configuring ASA 5505 to be able to ping remote host.Setup - We have a site-to-site (192.168.1.0/24 - 192.168.2.0/24) VPN setup with client VPN access (IP Pool, 172.16.50.0/24) on 192.168.1.0 ASA 5505.Issue - Not able to ping host on 192.168.2.0 from VPN client 172.16.50.0 but able to ping 192.168.1.0 host.
View 8 Replies
View Related
Mar 14, 2012
We have a VPN using 857 and 877 routers as remote connecting in to a 2800 EZVPN Server.
The VPN is working fine. However, the VPN connections sometimes (after a few hours/days) seem to "freeze". A "show crypt sess" shows the connections as Up/Active, but you can not ping antyhing from remote to server, or visa versa, nor does any traffic flow. I then added a "isakmp keep-alive" on the 2800, which improved the situation a bit, but not as much as I hoped.
On the 877 I then implemented a IP SLA, with Object Tracking and then use a Event Manager to just issue a "clear crypto session" . This solved the problem.
However, what do I do on the 857 ? It does not support Object Tracking or the Event Manager. Is there any other mechanism to monitor and reset these frozen/stale VPN connections automatically ?
View 5 Replies
View Related
Sep 9, 2012
I am having problem connecting to my work PC via VPN Cant ping and RDP. I sometimes need to log into my work PC to check out a problem. I connect via VPN and I can access servers (using Citrix and local intranet sites) that can only be accessed once connected to my work domain. So it looks like the VPN actually works fine.
But I cannot Remote Desktop Connection to it. I also tried to ping the PC using a command prompt. Using the command prompt, I ping MyWorkPC And I can see that it tries to ping MyWorkPC.domain.name.co.za. So it looks like it sees the MyWorkPC on the network. But all pings fail.
A work colleague tried to remote connects to MyWorkPC from his home PC and he can successfully connect. So I do believe that the work network and PC is setup correctly. I am running window 7 Ultimate SP1 (32bit) with a 3G dongle in a router. I also have Avast antivirus installed on my PC. I was not sure if the router or the antivirus was the issue so I tried:
1.Removing the 3G dongle and attach it to my USB port on my home PC directly. No luck
2.Some blogs said that the P2P or IM shield on Avast might be the problem so I disable it. No luck
3.Then I uninstalled Avast completely to see if it has any shield that might still block it. I restarted. No luck
View 2 Replies
View Related
Sep 27, 2012
I have 4 x 2960 switches in a remote site. These are managed by an NMS in our DC, the NMS IP ends in 35.100 with a /23 mask.
When they are first booted, the switches are visable to the NMS, but after a week or 2, 3 of them drop connection to it. If you reboot them again they are fine. You are able to log onto them form thier local router and use a Radius server which is in the same subnet as the NMS.
The odd thing is, whilst they can not ping the NMS, they are able to ping any other addresses in the 34.0/23 range.
The config on the one that does not lose connection is the same as the other 3 and I have also rebooted the NMS.
View 3 Replies
View Related
Nov 2, 2012
I can use PPTP and access all the PCs on a flat network at a remote site. I can ping the pcs and connect with netsupport manager. When I use QVPN I cannot do this. Why? I have added custom ports 5405 for NSM and applied ACL put no joy. I also added PING to ACL but it still doesn't work.
View 1 Replies
View Related
Jun 6, 2011
I've setup a CISCO 871 which receives DHCP IP address on WAN interface Fa4 and DHCP-assigned static IP Address on virtual-ppp1. The static address is used for site-to-site VPN's, while I've planned the DHCP address for standard web access and CISCO VPN Client dial-out.
Internally, I've created 2 VLAN's, one for standard PC's with access to the remote sites via site-to-site and cisco client, and the other for a 'secured' area with only HTTP/S allowed out. [code]
Clients in the PCLAN should also be allowed to dial-out using CISCO VPN client to remote sites via the OUTSIDE interface. This is partially working because the client does log into a remote site, however I cannot ping or rdp remote stations once connected."ip inspect log drop-packets" does not reveal dropped packets when trying to ping or rdp. [code]
View 5 Replies
View Related
Apr 16, 2012
I recently purchased a RV110W wireless router for a client. I am having issues with the VPN access. Here is the client's access log:
2012/04/17 10:59:41 [STATUS]Disconnecting...2012/04/17 10:59:47 [STATUS]Success to disconnect.2012/04/17 11:00:03 [STATUS]OS Version: Windows XP2012/04/17 11:00:03 [STATUS]Windows Firewall is OFF2012/04/17 11:00:04 [STATUS]One network interface
[Code].....
I've called Cisco tech support but the answer is disregard the log message and everything is working, and that I have a configuration issue on my end.
View 2 Replies
View Related
Jun 11, 2011
I have two computers side by side 192.168.1.7 and 192.168.1.8 both running xp pro sp3. On 8 I can RDC to the 7, but on 7 I cannot RDC to 8. I can see port 3389 listening on both using netstat -a. But 7 just can't RDC connect to 8. 7 cannot ping 8 either. I have the firewall turned off on 8, I had tried allowing RDC 3389 earlier with the firewall but that didn't work either.I don't have any extra firewalls running.Life will be like perfect, if I can just RDC to 8.Both are on the same wired belkin wireless router, 4' from itl.I tried taking the no ping no rdc computer to work and it didn't work there either.
View 19 Replies
View Related
Apr 18, 2013
I have a need to Remote Desktop connect to company’s employees for support then they are abroad and using Cisco AnyConnect client.Cisco AnyConnect client connection works fine, clients can reach company’s inside network without problems, but I cannot make revers connection, I cannot Remote Desktop connect or ping VPN clients from companies inside network. I cannot ping clients from ASA too.I am using ASA 5520, Cisco Adaptive Security Appliance Software Version 8.4(3) Device Manager Version 6.4(7), and Cisco AnyConnect VPN Client 2.2.0133. Protocol Encryption- AnyConnect-Parent SSL – Tunnel DTLS-RC4 RC4 AES 128.
View 0 Replies
View Related
Apr 20, 2012
I am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.
View 8 Replies
View Related
Apr 7, 2011
I have an GRE Tunnel across my head office and remote site with multiple subnets using cisco 1841 routers.I can ping most of the devices on the remote side, but I can not ping certain devices.These devices respond to ping requests on the local LAN, but not through the WAN link. If I change the IP of device than it start responding. I am using same gateway and mask on these devices.The remote site is running classic STP on switches with distribution switch being the root bridge.
View 4 Replies
View Related
Sep 6, 2012
I have a RVS4000 with client VPNs setup and have created all 5 users......trouble I run into is that when one of the users attempts to connect to the VPN from a second device (ie the sixth device to connect to the VPN), the connection does not establish....cannot ping remote server (using QuickVPN). In looking at the logs, the device that isn't working is getting a different IP (172.16 vs 192.168). I know I'm limited to 5 users, but am I limited to 5 devices as well?
View 2 Replies
View Related
Apr 20, 2011
i have a new smc router and my local ip address and remote ip addresses are very similar. The remote ip address is updating my dns server but i am unable to ping it. Its something like 122.61.xxx.1 ?
View 8 Replies
View Related
Apr 30, 2013
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies
View Related
May 30, 2012
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
View 3 Replies
View Related
Apr 3, 2013
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
View 9 Replies
View Related
May 7, 2012
I have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 Replies
View Related
Aug 16, 2012
Im currently connected to a remote acess vpn setup using the vpn client and am unable to get anywhere around my network, this normalyl works fine The only difference i can see is that the are multiple virtualaccess interfaces pointing to my public ip address, which im presuming is causing routing issues How can i clear these unsed virtual access lines and how can i make it forget them automatically after disconnects?
View 5 Replies
View Related
May 17, 2011
We have an ASA5510 and a few days ago we were unable to access some segments from remote access VPN, the problem was not the config. A few hours later the problem was resolved on its own and I suspect we have an IOS bug. This has happened a few times in the past and its becoming an issue. How can this be confirmed and which IOS should we upgrade to? Prefer not 8.3 given the syntax difference
View 1 Replies
View Related
Jun 27, 2011
I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
View 2 Replies
View Related
Nov 1, 2011
Based on my diagram, my computer A (192.168.100.11) can ping and access my computer B (192.168.10.14). But, when i'm home and i use remote access vpn (192.168.200.x) in cisco asa 5520 to connect to my computer A is okay. But, when i try to ping my computer B is not okay. I already do the exemption for 192.168.100.x and 192.168.10.x in nat rules for inside interface (192.168.100.2) ...
Should i put routing from outside 1.1.1.2 to 192.168.10.x by using 192.168.100.1 as a gateway?
View 1 Replies
View Related
Oct 11, 2011
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies
View Related
Apr 16, 2013
I used to access my NAS by typing "\mydrive" in the folder path. But after I have added computers into my local network, some computers became failed to access the NAS (it shows that it cannot find the specific location). I can still ping the NAS IP and also other computers in the network.
View 3 Replies
View Related
Jan 6, 2012
I have a site-to-site VPN (no client software) that is up and I can ping all the IPs on the other side.
My computer is connected to .2.0, remote LAN is .1.0
I can view all of the local LAN (.2.0) devices in Network Location, but can't access the shared resources on the remote .1.0 LAN.
ServerFolder shared directories is mapped as a drive and worked yesterday. It now has a red X on in and I can't access it, but can ping \Server's IP address.
View 1 Replies
View Related
Mar 25, 2011
I recently bought a new DLink 615 E4 router.After a botched firmware update, I attempted to enter the emergency room.I got in once, and tried to upload the firmware using Internet Explorer 8, but it was stuck there for over two hours without any progress (stuck at the browse/upload page), so I disconnected it.
I haven't been able to enter the Emergency room since then. I get to the point where the power light blinks orange, and connecting my laptop to the router using the wired connection lights up the proper LAN light, but I cannot ping or access 192.168.0.1 anymore.
View 1 Replies
View Related
Apr 16, 2013
I have a RVS4000 and I would like to setup a Ping monitoring from the outside to a device behind RVS on lan network. I have created a rule to allow a service PING for range from WAN 46.xxx.xxx.xxx - 46.xxx.xxx.xxx to host 192.xxx.xxx.xxx but unfortunately this is not working. I can confirm that I can ping host 192.xxx.xxx.xxx from diagnostics on RVS.
View 2 Replies
View Related
Jul 23, 2012
I am new to Cisco and am studying for my CCENT certification. At the moment, I am attempting to correctly configure a Cisco 871W lab router. Since I have undertaken this task, I have run into nothing but problems. First off it was finding that the previous owner had left a password on it, having to purchase a new USB to DB9 adapter to pass the "break" sequence to the router, and then resetting the router in ROM Monitor mode.
Now, I cannot seem to configure the router correctly, and am quite stumped.
My ISP is Charter (cable internet), and the home network that I am using consists of a Motorola SBV5122 Digital Voice Modem, Motorola SB6120 Cable modem, and, ideally, should also include my Cisco 871W router.
When I connect my router to the SB6120 Cable modem, the router receives an IP address via DHCP and the WAN indicator light turns on.
I have a VLAN configured on the 4 switchports of the router, and it is setep to act as a DHCP server. However, when I connect my PC to rhe router via Cat5e Crossover cable, I cannot access the internet. The router gives the PC an IP address, yet all attempts to ping the PC from the router fail. Somehow, I can connect to the router via SSH though.
Furthermore, I can ping the 127.0.0.1 loopback address from my PC, but cannot do so from the router.
how to correctly configure this router to function as intended in my network situation, however, this is proving to be seemingly unsurmountable!
I have attached the config of my router along with both outputs and commands relating to my predicament.
View 11 Replies
View Related
