D-Link DIR-615 :: Way To Ping Or Access 192.168.0.1?
Mar 25, 2011
I recently bought a new DLink 615 E4 router.After a botched firmware update, I attempted to enter the emergency room.I got in once, and tried to upload the firmware using Internet Explorer 8, but it was stuck there for over two hours without any progress (stuck at the browse/upload page), so I disconnected it.
I haven't been able to enter the Emergency room since then. I get to the point where the power light blinks orange, and connecting my laptop to the router using the wired connection lights up the proper LAN light, but I cannot ping or access 192.168.0.1 anymore.
I'm trying to do port forwarding on my DIR-615...first of all I need to be able to ping the router from outside! I did enable the ping options to allow request from WAN...still don't work!!I removed the router and plug my laptop directly on my cable modem adapter and I'm able to ping my IP address (did put the same address the router had)...so, the IP is OK and it is possible to get in the modem from outside.I did plug back the router, and still not working...I did some trick like enable all IP with the Inbound filter...give access to few MAC address that I have to give more chances to get in and still not working!!!
I would like to passthrough ICMP 8 (ping) requests through the DIR-655 to my server. I found where to allow the router to respond to ICMP 8 requests, however, I do not want the router to responder, rather the server itself. Is there a way to pass these requests through to the server?
Who is trying the ping www.dlink.com ? I have been used the model DIR-825 during 1 year, but I could not see that ping command in the log. I had experienced that my notebook alert that DIR-825's shareport has reconnected. Why the DIR-825 lost the private connection while I sleeping?Comment: DIR-825(IP: 10.10.100.97/28) is private using only. The internet gateway is setting to DIR-655(:192.168.90.97/29). [code]
I used to access my NAS by typing "\mydrive" in the folder path. But after I have added computers into my local network, some computers became failed to access the NAS (it shows that it cannot find the specific location). I can still ping the NAS IP and also other computers in the network.
Using DIR-601 hardware version B1, Firmware 2.00NA, I am debugging problems I've had with this router, so it is set up on my network so I can access it from both the WAN and LAN side. If I ping the router from the WAN side, I get a very fast response. But when I disable ping from the administrative tools from the LAN side and reboot the router, I still get responses to my ping! I know the router is responding because if I disconnect the WAN cable from the router (connected to "INTERNET", the pings stop. So the router is ignoring user settings at Advanced->Advanced Network->WAN PING! Looks like a firmware bug.
I am running a DAP-1522 (v1.21) in Bridge mode with a DIR-615 (1.00VG). I have configured the DAP-1522 to access the WiFi network and can see it connects correctly. I have a PC connected to the DAP-1522. Most of the time I can ping the DAP-1522 from the PC but cannot ping the DIR-615. Occasionally when I reboot everything again I can ping the DIR-615 and get full internet access but this usually only lasts a minute or so then it drops. After that I can only ping the DAP-1522. The DAP-1522 always says the Status is "connected" though.
The IP addresses are as follows: DIR-615: 192.168.0.1 DAP-1522: 192.168.0.50 (static) PC: 192.168.0.55 (static)
Region : UnitedStates Model : TL-WR1042ND Hardware Version : V1 Firmware Version : WR1042ND v1 00000000 ISP : comcast
I have a machine called 'survtest' on my lan with a permanent ip addr of 192.168.0.112. I can't ping that host by name from any other machine on the lan, although I can ping the ip address. Not only that but this machine appears in the DHCP client list within the router with its name 'survtest' and correct IP addr.
There is another machine on the lan called 'bsd' that also has a permanent IP addr of 192.168.0.110. It can be pinged by name from any other machine on the lan. However it does not show up in the DHCP client list at all.
Neither of these machines can be pinged by name from within the tplink admin diagnostic screen.
Both my DIR-655 and DIR-815, when setup as wireless access points, are unable to ping external IP addresses and thus cannot contact the dlink ntp servers. I've disabled UPnP, disabled DHCP, changed the LAN IP address to an available address on the network. The wireless works, devices are getting an IP from the network DHCP server and can surf the internet. But the DLink router itself cannot ping any external IP addresses. But the DLink router itself cannot ping any external IP addresses.
I have a site-to-site VPN (no client software) that is up and I can ping all the IPs on the other side.
My computer is connected to .2.0, remote LAN is .1.0
I can view all of the local LAN (.2.0) devices in Network Location, but can't access the shared resources on the remote .1.0 LAN.
ServerFolder shared directories is mapped as a drive and worked yesterday. It now has a red X on in and I can't access it, but can ping \Server's IP address.
the problem is that I'm suffering from ping spikes. When I ping my router it looks something like this:
C:UsersNiklas>ping 192.168.1.1 -n 10
Skickar ping-signal till 192.168.1.1 med 32 byte data: Svar från 192.168.1.1: byte=32 tid=991ms TTL=64 Svar från 192.168.1.1: byte=32 tid < 1 ms TTL=64 Svar från 192.168.1.1: byte=32 tid=2944ms TTL=64[code].....
Region : Kazakstan Model : TD-W8951ND Hardware Version : V4 Firmware Version : 4.0.0 Build 120207 Rel.10587 ISP : Megalne
I have two comps in LAN (Ethernet) - one (Comp1) in WinXP, another (Comp2) in Win7. IPs for both comps are assigned by DHCP. Internet is available for both Comps and for assigned wireless units. So the router is configured almost well. But I lost my home net: can't see or ping anything in LAN. Setting of static IPs (192.168.1.4 and 192.168.1.6 are permitted)
Since buying and using this router about 1 month ago, I've had latency problems. With my Linksys WRT54GL, my latency has always been consistent. However, pinging to google (as a benchmark), my ping is a good 50-70 higher than directly plugging into my router. Directly into my modem I get 10-20ms pings; through the router, I get minimum 60ms up to 100ms spikes. When using the Linksys router, my ping would be 20-30s. I really hope it's just a settings problem. I've turned off QoS and wireless to isolate the connection to just wired, but it still persists. I really hope I can fix this problem, else I am going to buy a different router over the weekend. I can't play FPS games like Bad Company 2 with such high latency.
I bought a DIR-600 a couple of months ago. Days later started experiencing problems, connection would drop, and only way to restore connection was to reset the router.It has its password configured, a secure wireless connection also configured, and Wan Ping is disabled.Yesterday I called D-Link support, and they asked me to update firmware (from 2.03 to 2.05). I did, but problem still here.Today I realized that there is a log section, and when I entered this is what I found?
I was able to go onto the internet with no problem. I've been searching forums trying to solve my problem but to no avail. I have Windows XP installed, I can connect to the LAN network but I cannot go online. I can ping the gateway but not the DNS as well as other address name or ip address. This is the output of ipconfig /all:
Description : Realtek RTL8139/810x Family Fast Ethernet NIC Dhcp Enabled : Yes Autoconfiguration enabled: Yes IP address: 192.168.1.145 Subnet mask: 255.255.255.0 Default Gateway : 192.168.1.1 DHCP Server : 192.168.1.1 DNS Servers : 202.160.8.2 202.160.6.20P.s: All the other computers in the LAN can connect to the internet.
I have a home network of 3 cmputers. DHCP from router. 1 computer is not getting address. But if I assign it one, with same gateway and dns(not a duplicate ip of others), it can ping internally, and outside. I can do tracert to 8.8.8.8 and ping it (google DNS). But I can't get to internet. So - i can get out, but nothing coming in. I have checked firewall.
Remote access VPN. Its configured on a Cisco PIX525 running ver 6.3(5) (old I know!) and I am running Cisco VPN client ver 5.06.0160 on the client end. Ok so here's the thing. The client connects ok, and it gets an IP address no problem. But I cannot ping anything on the remote LAN. So the client is coming across the internet, the VPN adapter has a 192.168.1.1 address assigned by the PIX and I am trying to ping the 192.168.0.4 address assigned to a switch on the inside of the firewall but with no joy. [code]
Region : Italy Model : TL-WR841ND Hardware Version : V8 Firmware Version : TL-WR841ND_V8_120802I
Setup the WR841ND in wds and easily connect to d-link.with the ping utility of the WR841ND I can reach the d-link or any of the PCs attached to the d-link and receive an answer.but any PC 'attached via LAN or WIFI to WR841ND can ping only WR841ND and not the d-link or any other PC attached to the d-link (clearly not even go on the Internet
I was having very high ping spikes (up to 2000ms) in my online gaming. I even had high spikes (up to 80ms) just pinging my router. It happened with every computer on the network. After several weeks, I narrowed it down to one thing: Enable DNS Relay. I unticked that, and instantly the spikes went away. However, my brother's Blackberry Playbook has been acting up now that DNS Relay is disabled. Basically, every day, the internet on that thing screeches to a halt, forcing him to reconnect to the network. It's basically a minor inconvenience, but it's one I want to correct. If I turn on DNS Relay again, the ping spikes will return. Interestingly, I switched ISPs during this time. I'm on cable now. I used to be on DSL with a different router, yet I had the exact same problem. The blackberry is probably integral to this problem. So I'd like to know if there's anything I can do to make DNS Relay work properly, allowing his stupid Blackberry to work, while maintaining the integrity of the network.
I'm trying to setup my home network so that I can access it when away from home but I've ran into problems and I can't figure out what is causing the problem.I've setup the router to forward incoming requests on port 80 to be directed to my PC running WAMP. The PC has a static IP and if I access it from another PC on my network I get the WAMP page load as expected.I've also setup an account with no-ip.com to resolve my (dynamic) ip. If I use the address they have setup while I'm on my network I get the login page for the router, again this is what I expect.The problem begins when I try and access my home address (whatever.no-ip.biz) from outside my network. I've tried it from 2 different locations and via a dial-up account and I get nothing.
It works on the mobile site at times maybe twice a day but only able to access for 10 minutes maximum. I tried the command prompt and ping facebookm and noticed that I didnt recieve files back and it was just timing out is that whats causing it?
I have a Linksys e4200 and a EnGenius EAP300. I setup new EnGenius AP to 198.162.1.5 and the Linksys is 198.162.1.1. The two devices are connected with Ethernet capble with a POE switch in the middle. Internet connection thru the Linksys works fine. However, the EnGenius does not connect to the Ineternet (Gateway is set to 198.162.1.1) Also when connected to the Linksys, I cannot ping the EnGenius.
I have a ASA 5505.|I configured it for remote access VPN from cisco VPN client.the ASA receives a public ip address on outside interface via PPPoE.I can connect to public ip of outside interface and address 10.1.1.2 is assigned to my Cisco vpn client.the problem is that I Cannot ping or reach ASA internal IP address 172.16.29.1 in any way when I am in VPN from outside,while I Can ping other hosts on 172.16.29.0/24 when connected in VPN.this is a problem brcause when I am connected in VPN to ASA I Cannot configure it..Then I Wanted to ask if it is possible a configuration which gives addresses from network 172.16.29.0/24 (the same as inside network) to VPN clients instead of another network (10.1.1.0/24) [code]
I have a RVS4000 and I would like to setup a Ping monitoring from the outside to a device behind RVS on lan network. I have created a rule to allow a service PING for range from WAN 46.xxx.xxx.xxx - 46.xxx.xxx.xxx to host 192.xxx.xxx.xxx but unfortunately this is not working. I can confirm that I can ping host 192.xxx.xxx.xxx from diagnostics on RVS.
I am new to Cisco and am studying for my CCENT certification. At the moment, I am attempting to correctly configure a Cisco 871W lab router. Since I have undertaken this task, I have run into nothing but problems. First off it was finding that the previous owner had left a password on it, having to purchase a new USB to DB9 adapter to pass the "break" sequence to the router, and then resetting the router in ROM Monitor mode.
Now, I cannot seem to configure the router correctly, and am quite stumped.
My ISP is Charter (cable internet), and the home network that I am using consists of a Motorola SBV5122 Digital Voice Modem, Motorola SB6120 Cable modem, and, ideally, should also include my Cisco 871W router.
When I connect my router to the SB6120 Cable modem, the router receives an IP address via DHCP and the WAN indicator light turns on.
I have a VLAN configured on the 4 switchports of the router, and it is setep to act as a DHCP server. However, when I connect my PC to rhe router via Cat5e Crossover cable, I cannot access the internet. The router gives the PC an IP address, yet all attempts to ping the PC from the router fail. Somehow, I can connect to the router via SSH though.
Furthermore, I can ping the 127.0.0.1 loopback address from my PC, but cannot do so from the router.
how to correctly configure this router to function as intended in my network situation, however, this is proving to be seemingly unsurmountable!
I have attached the config of my router along with both outputs and commands relating to my predicament.
I want to configure multilink between two Cisco 7206 routers POS interfacesafter configuring both sides.Router 1interface Multilink5 ip address. [code]. I can see both sides through show cdp, also ospf process goes to FULL stateBut traffic is not flow between interfaces, and i can not even ping router's own ip address.When i delete network statement from ospf process, i can ping router's own interface and both routers can ping each other.
every time i try to acces my linksys router my IE just auto adds http:// and opens google search results. I cannot make IE not auto add that freaking http thing, on the old win XP i could type in 192.168.1.1 and it just went straight to my router login. Do i disable this IE auto http crap? i simply cannot acces my router anymore??i can ping the router, even using Cisco network magic pro I tried to reset router checked my internet settings everything works fine, this pc has a dhcp auto configuration etc.
I have 1 PC and 2 laptops. All are connect to the WAG160N router. All 3 can access the internet but they cannot see each other, not even by ping.I have turned my Kaperksy internet Security off and this makes no difference. Windows Firewall is turn off.
I have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these access methods worked properly for me.I believe I may have inadvertently changed something as of Friday using ASDM. I am mostly assuming this because, as of yesterday I can no longer connect to the device. I actually cannot even communicate with it (ping the interface I normally use to manage, which I could previously ping). No computer on the same subnet as me is able to ping the interface. The device is still accepting VPN connections, dishing out DHCP addresses and everything else it normally does, but I really need to be able to gain access to it again. I am thinking to reboot the device when there is some downtime, in the hopes that ASDM doesn't save to startup-config and only to running-config.
The VPN will connect.I can ping and connect to the ASA 5510 on it's LAN interface.My problem is that I cannot ping or access anything on the LAN past the firewall. What am I doing wrong?
Here is my config.Result of the command: "show config"
Saved : Written by enable_15 at 22:55:02.299 UTC Tue Jan 10 2012 ! ASA Version 8.2(5) ! hostname ********
