I have a Q1000 and I'd like to be able to "ping yahoo.com" (etc) once in a while when I think there may be a network problem. From my desktop I type > ping yahoo.com and nothing happens. I can ping other device on my LAN but the only way to ping somewhere outside is to http://myrouter -> Utils -> Ping test.
View 4 RepliesI'm having difficulty connecting my desktop to my wireless network. Some details to start off: I'm using a G-Sky usb wifi adapter model number GS-28usb. I recently moved from an apartment with free wifi and I set up broadband with Qwest/CenturyLink. The modem/router is an Actiontec Q1000. The firmware is up to date (I checked) and every other device I bring into the house can connect just fine (laptop, roommate's desktop and laptop, and my blackberry) I'm running Windows 7 x64 Ultimate on all machines, with all updates currently available. My network shows up in the list of available networks, signal strength fine, but when I try to connect, it does its initial "getting information..." in the small box in the corner of the screen, then the box disappears and no connection is made. The status of my adapter at that point will say "attempting to authenticate" and will remain like that even though (apparently) windows has given up on trying to connect to the network. It never gets to the point where it asks me for the passkey. I've changed just about every variable I can think of that might affect this on the router (encryption type, b/g/n, legacy mode, compatibility mode, etc, i've renamed the network, powercycled the router, etc) all to no avail. I've tried to manually add the network settings under wireless profiles, but even though the information I put in is EXACTLY correct, under available networks its says that my settings don't match those on the network. I've tried different wireless adapters, and none will connect, so I've eliminated a faulty adapter. I can connect to my laptop with an ethernet cable, and bridge the connections so I can use the internet on my desktop, but i cannot connect directly to the router.
here is my ipconfig/all:
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersPancho>ipconfig/all
[Code].....
I have my internet through CenturyLink which is a DSL connection running on an Actiontec Q1000 on a Windows 7 set up. I'm trying to run a subsonic server on my computer to stream my music collection. It was all working beautifully until I had to switch to this modem from my previous. Now, when I go to canyouseeme.org, it can't see that 4040 and 8080 are open. They need to be for subsonic to work? I've tried to set it up as portforwarding
View 5 Replies View RelatedSo we just got a new router for our higher speed internet. The modem is an Actiontec Q1000 from Qwest. We used to live out in the middle of nowhere, so we never needed to secure our internet. Now we live close to neighbors and we need to encrypt the wireless. When I try any encryption, however, I can't connect at all. I have tried temporarily having it unlocked and I could connect without a problem. It also works fine when I'm using my Ethernet cord.
Heres my IPCONFIG.
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Owner-PC
Primary Dns Suffix . . . . . . . :
[code]....
I'm on a Mac running OSX. Qwest (my ISP) recently swapped my DSL modem for an Actiontec Q1000 combo modem/router. The Q1000 firewall is not nearly as configurable as my Linksys BEFSR41 (v3) router. I'd like to use the Q1000 just as a modem and use my Linksys as my router so I can access it's superior firewall configuration.
How do I physically hook the hardware up?
How do I configure the 2 items. The Q1000 uses 192.168.0.1 as it's web address. The Linksys uses 192.168.1.1. I have 2 Macs on my network, an iMac (OS 10.5.8) and a G4 (10.3.9).
Besides web browsing & email, I also have a torrent client I use (Azureus).
I am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 198.168.1.109 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080.
But every configuration I have tried does nothing of the sort.
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies View RelatedI set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies View RelatedFrom My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View RelatedWhen I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
I installed window server 2003 in a old Pentium III server as a standalone test server. Now I want to use it as a print server and connected it to the domain. I can ping workstations and other servers from that test svr. But i cannot ping that test server from the work stations.
View 2 Replies View RelatedI had both a Westell 7500 and a Linksys Router working fine and had my 360 setup as an extender for Windows Media Center so I could stream TV, Music, Movies, etc from my desktop to the 360. Then I switched my modem/router out with a Zyxel PH5001Z
So now today I noticed that I can no longer find my desktop through the XBox. I have adjusted my firewall settings on the modem itself, even completely disabling it. UPnP is enabled for the 360 and the device is showing under my device table. At first I wasn't able to ping any network devices but after creating an ICMPv4 Firewall rule it worked fine. I've confirmed the XBox IP Address through Network Map, the Device Table on the modem and through Network Settings on the XBox. I've diabled my modem firewall as well as Windows Firewall, completely and I still can't ping my XBox or set it up as an Extender.
I have the XBox connected wirelessly using WPA2-Personal and it's operating in 802.11g/n mode.
I have a strange issue on my ASA 5510 (8.4). I can't ping or connect to the VPN clients but the VPN clients can ping/connect to any inside resources. I have checked all the NAT extemtion entries.
View 3 Replies View RelatedBeen racking my brains out for hours now, my remote access VPN via Cisco VPN Client is UP i can ping the RA VPN DG but cant get no further than that relevant config below i can ping 192.168.250.1 and it replies with the public ip address, but i cant ping any 192.168.101.* addresses.
View 1 Replies View RelatedIm having some Ping / MS issues lately. My ping bounce up and down from 30 to 600 in just some seconds, and its really unstable. Im using the same internet as my neightbour ( internet cable through the wall) Is there any1 who can give me some tips so I don't need to worry about my ping anymore?,I don't know much about he's internet though.
View 3 Replies View RelatedI Have 15 computer and they all are in Internet Connection.And I Have Network of C class that is 192.168.5.11.But the main Problem is that the computer are not getting ping with each other.How can I get them Pinging between them.Can any antivirus stop them?
View 1 Replies View RelatedI have Windows 7 x64 on my desktop, laptop, and HTPC. The past few months, everything worked fine. Today, I can ping my IP address but I cannot ping the host name on all 3.They also do not show anything in the network window, just the computer that I'm on.
View 1 Replies View RelatedI'm using xp pro. Sharing is enabled. No firewall. I can ping between both pcs. I've run the network wizard on both pcs. I can only share one way. The other gets the error don't have permission.
View 7 Replies View RelatedI installed the GFI Webmonitor proxy on my network. Previously my ping was 83ms now it can get up to 2500ms. Is there anyway to reduce this?
View 3 Replies View RelatedI used to access my NAS by typing "\mydrive" in the folder path. But after I have added computers into my local network, some computers became failed to access the NAS (it shows that it cannot find the specific location). I can still ping the NAS IP and also other computers in the network.
View 3 Replies View RelatedI am wondering how I can attain a higher ping...
First my specs:
I have DSL, with the modem my ISP has provided me with..
I have a belkin wireless G router (which I want to upgrade to a Dlink wireless N 815, as soon as I can hook it up)
My ethernet adapter is intregated into my mobo, which is a ASUS P5K motherboard, with 10/100/1000mbps ethernet.
I am wondering what I can do to get a better ping?
The best ping I have ever had (on an idle system) is 25ms.
is there anything I can do to get a better ping?
(also, I live within 100km of large city centers. I do not live out in the middle of nowhere)
I'm really lost with this issue. its been going on for months. here is a copy paste of my ping to yahoo. "ping yahoo.com -t"
View 1 Replies View RelatedThis started out as a printer issue and then evolved into a networking issue.let's see if i can include all the details here. the laptop in question is having problems talking to other internal network computers/printers. i am on a 192.168.10.? network, the laptop has a dhcp assigned address, my domain controller/dns/dhcp server has an address of .3, i have a fileserver at .9, my default gateway is .1 the laptop can ping all 3 of those computers.i have a printer with .130 address, the laptop times out when pinging it. there are around 15 or 20 other computers on the network with dhcp assigned addresses.so far i cannot get the laptop to ping any of those.
The same thing happens whether i am connect using the Local Area connection or wireless, so 2 different NICs, same laptop though.the laptop can ping any outside address, the firewall is turned off, the other computers that i cannot ping can ping each other and the printer. here's the real kicker, i noticed while running ping 192.168.10.130 -t when i do a repair on the network connection, the darn thing will ping the 130 address 3 times then start timing out again? is going on? i have killed every weird ass service i can think of, i have booted up in safemode with networking with the same result. i have signed in as a different user, i have looked at the routing, the host file, nothing looks weird to me at all. i have also run the winsock fix for xp......
i can't get my ping of client ip.
View 1 Replies View Related2 windows 7 machines.at work..They are both laptops. one acts as a server for a piece of software to the other one.on the "client" laptop I can map a drive to the "server" and browse files through that maped drive etc.I can also ping the IP address of the "server" but I get a timed out when I try to ping the computer name.Server had Macafee firewall, I uninstalled that, and I turned off Windows firewall on both machines.the software needs to be able to ping by name I guess in order to work..
View 2 Replies View Relatedi want to know how to reduce my ping while playing counter strike condition zero online ??
View 1 Replies View RelatedWe've got about 15pcs at work, all on one network. All connect to one switch, and the router connects to the switch so all has internet access. Four pcs has got windows vista on, the rest XP. Yesterday I tuned on the one pc with Vista on, but could not connect to a mapped drive. I checked in the network places, i could see only three pcs, all three xp pcs. I can browse the internet, but not the pcs on my local network, and I can ping the pcs on the network.
View 1 Replies View RelatedOk, I have a ASA 8.4 firewall that I have been working on so long. It was a hassle to configure the object group and nat for 8.4. So, I put two host in both side of ASA to test pinging but I can not ping the outside or the DMZ. I attached my nat config.
View 1 Replies View RelatedI have a network with three vlans: vlan 10 (172.16.10.0), vlan 20 (172.16.20.0) and vlan 30 (172.16.30.0).I want to make sure that clients in vlan 10 can access to vlan 30, but not access to vlan 20.Vlan 20 can also access only vlan 30.i have configured a router on a stick and the acl's, but some how i can't ping from vlan 20 to vlan 30. [code]
View 1 Replies View Relatedwhen we ping from pc in lan 1 to pc in lan 2, what protocols we walk through in request and in response??
View 14 Replies View Relatedcant get online,found that the internet IP ping failed
View 24 Replies View Relatedwhile trying to hookup wireless cant det past gateway ping on test. Iv'e used addresses given to me by net gear.
View 5 Replies View RelatedThe server is on a different network and the desktop is on a another network.I can ping the server but i can't access any drive on the server.
View 1 Replies View Related