Im having some Ping / MS issues lately. My ping bounce up and down from 30 to 600 in just some seconds, and its really unstable. Im using the same internet as my neightbour ( internet cable through the wall) Is there any1 who can give me some tips so I don't need to worry about my ping anymore?,I don't know much about he's internet though.
View 3 RepliesI am trying to get a vlan change done with CoA and MAB on a WLC 7.2 but it looks like it doese't disconnect the client, hence no new dhcp request.
Everything is working except 'port bounce'. I can see the new vlan in the controller, if i do a ifconfig /renew on the client it gets the new subnet and everything works as it should. If i remove the endpoint in ISE it swaps the vlan again on the controller, but no port bounce.
I found that the domain name was hosted at enom.com and the email was gmail. The web servers are both Media Temple servers.we updated the settings on the new server using google's instructions. However, it is still not working properly. So, to be as clear as possible, here is the specifics:
Email from the outside works fine, Email internal to external works fine, email internally (from one emplyee to another internally) will bounce giving a 550 error. After researching this error, I found that several people have had this issue, however, the majority of the fixes didn't work.
We are facing a strange issue with GRE tunnel. We are using this tunnel from a branch office to Hub office. All other tunnels terminated on Hub router are working fine. Issue with this tunnel is that whenever WAN connection goes down Line protocol on tunnel interface some times comes up and sometimes not (therefore we have to reset the tunnel interface and it comes up). IOS used on this router : c2900-universalk9-mz.SPA.152-1.T2
View 5 Replies View RelatedHave two WRT54G Wireless Routers.
-One WRT54G ver. 6, Firmware Version v1.028
-One WRT54G ver. 6, Firmware Version v2.x
With the WRT54G ver. 6, Firmware Version v1.028.When I ran the android app WiFi Analyzer, I get mixed results.On my Samsung Galaxy S3, I saw my signal on Channel 2, and others around me (two on Channel 6 and two on Channel 11).On my ASUS Transformer Prime TFT201 I see the same signals, but my router signal bounces continously between the baseline (-100dBm?) and about -35dBm.
Plugged in the WRT54G ver. 2, Firmware Version v2.x Channel 8.Hooked it up and got good steady signal strength. It Had 'WPA - Shared Key' but did not have the 'WPA - Personal' that was on the ver. 6. So, I had to go and screw things up. I've upgraded this to Firmware Version: v4.21.5 and guess what? I now have 'WPA - Personal'. I also have a signal is bouncing on BOTH units.
On my ASUS, I can see both routers. The ver. 2 AND the ver. 6 are bouncing between baseline and -35dBm, in unison. Apprently something in the ASUS does not like the later Firmwares.On my Samsung I can see the two signals - the ver. 2 on Channel 8 is stable as a rock and the ver. 6 on Channel 2 is also bouncing, but at a much slower rate! Running Speedtest.net a PC hardwired to the ver. 2 - I get 5.34 Mb/s Download and 0.47 Mb/s upload (yeah, my Internet sucks!) Running Speedtest.net through the ASUS/WiFi to the ver. 2 - I get 2.43 Mb/s Down and 0.65 Mb/s Up.Running Speedtest.net through the Samsung/WiFi to the ver. 2 - I get 5.07 Mb/s Down and 1.07 Mb/s Up.
When a client connecting to a specific AP (example AP01), after every 1800 sec uptime it will reconnect and join other unit AP (example AP02)Both AP physically installed distance is around 6 meters from each other. I conduct the testing where i get myself sitting in middle between these two APs.
01. If i disable settsion timeout this feature, or setting the seconds become higher value, what's the performance and security impact? Is it recomend to change the default 1800 seconds session timeout?
02. Is there anyway i can tweak on WLC controller to prevent the client after session timeout then associate with another AP. This will lead major performance impact as the client woudl possibility connect to the weak signal AP and effect on the performance.
These are the details for reference:Client detail
- Dell DW1520 wireless-N WLAN card, with firmware version 5.100.235.12
- CCX version 4 supported
- Layer 2 security is WPA2 personal with PSK.
- wireless radio an
Controller detail:
model is AIR-CT5508-K9
software version is 7.2.110.0
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies View RelatedI set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies View RelatedFrom My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View RelatedWhen I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
I installed window server 2003 in a old Pentium III server as a standalone test server. Now I want to use it as a print server and connected it to the domain. I can ping workstations and other servers from that test svr. But i cannot ping that test server from the work stations.
View 2 Replies View RelatedI had both a Westell 7500 and a Linksys Router working fine and had my 360 setup as an extender for Windows Media Center so I could stream TV, Music, Movies, etc from my desktop to the 360. Then I switched my modem/router out with a Zyxel PH5001Z
So now today I noticed that I can no longer find my desktop through the XBox. I have adjusted my firewall settings on the modem itself, even completely disabling it. UPnP is enabled for the 360 and the device is showing under my device table. At first I wasn't able to ping any network devices but after creating an ICMPv4 Firewall rule it worked fine. I've confirmed the XBox IP Address through Network Map, the Device Table on the modem and through Network Settings on the XBox. I've diabled my modem firewall as well as Windows Firewall, completely and I still can't ping my XBox or set it up as an Extender.
I have the XBox connected wirelessly using WPA2-Personal and it's operating in 802.11g/n mode.
I have a strange issue on my ASA 5510 (8.4). I can't ping or connect to the VPN clients but the VPN clients can ping/connect to any inside resources. I have checked all the NAT extemtion entries.
View 3 Replies View RelatedBeen racking my brains out for hours now, my remote access VPN via Cisco VPN Client is UP i can ping the RA VPN DG but cant get no further than that relevant config below i can ping 192.168.250.1 and it replies with the public ip address, but i cant ping any 192.168.101.* addresses.
View 1 Replies View RelatedI Have 15 computer and they all are in Internet Connection.And I Have Network of C class that is 192.168.5.11.But the main Problem is that the computer are not getting ping with each other.How can I get them Pinging between them.Can any antivirus stop them?
View 1 Replies View RelatedI have Windows 7 x64 on my desktop, laptop, and HTPC. The past few months, everything worked fine. Today, I can ping my IP address but I cannot ping the host name on all 3.They also do not show anything in the network window, just the computer that I'm on.
View 1 Replies View RelatedI'm using xp pro. Sharing is enabled. No firewall. I can ping between both pcs. I've run the network wizard on both pcs. I can only share one way. The other gets the error don't have permission.
View 7 Replies View RelatedI installed the GFI Webmonitor proxy on my network. Previously my ping was 83ms now it can get up to 2500ms. Is there anyway to reduce this?
View 3 Replies View RelatedI used to access my NAS by typing "\mydrive" in the folder path. But after I have added computers into my local network, some computers became failed to access the NAS (it shows that it cannot find the specific location). I can still ping the NAS IP and also other computers in the network.
View 3 Replies View RelatedI have a Q1000 and I'd like to be able to "ping yahoo.com" (etc) once in a while when I think there may be a network problem. From my desktop I type > ping yahoo.com and nothing happens. I can ping other device on my LAN but the only way to ping somewhere outside is to http://myrouter -> Utils -> Ping test.
View 4 Replies View RelatedI am wondering how I can attain a higher ping...
First my specs:
I have DSL, with the modem my ISP has provided me with..
I have a belkin wireless G router (which I want to upgrade to a Dlink wireless N 815, as soon as I can hook it up)
My ethernet adapter is intregated into my mobo, which is a ASUS P5K motherboard, with 10/100/1000mbps ethernet.
I am wondering what I can do to get a better ping?
The best ping I have ever had (on an idle system) is 25ms.
is there anything I can do to get a better ping?
(also, I live within 100km of large city centers. I do not live out in the middle of nowhere)
I'm really lost with this issue. its been going on for months. here is a copy paste of my ping to yahoo. "ping yahoo.com -t"
View 1 Replies View RelatedThis started out as a printer issue and then evolved into a networking issue.let's see if i can include all the details here. the laptop in question is having problems talking to other internal network computers/printers. i am on a 192.168.10.? network, the laptop has a dhcp assigned address, my domain controller/dns/dhcp server has an address of .3, i have a fileserver at .9, my default gateway is .1 the laptop can ping all 3 of those computers.i have a printer with .130 address, the laptop times out when pinging it. there are around 15 or 20 other computers on the network with dhcp assigned addresses.so far i cannot get the laptop to ping any of those.
The same thing happens whether i am connect using the Local Area connection or wireless, so 2 different NICs, same laptop though.the laptop can ping any outside address, the firewall is turned off, the other computers that i cannot ping can ping each other and the printer. here's the real kicker, i noticed while running ping 192.168.10.130 -t when i do a repair on the network connection, the darn thing will ping the 130 address 3 times then start timing out again? is going on? i have killed every weird ass service i can think of, i have booted up in safemode with networking with the same result. i have signed in as a different user, i have looked at the routing, the host file, nothing looks weird to me at all. i have also run the winsock fix for xp......
i can't get my ping of client ip.
View 1 Replies View Related2 windows 7 machines.at work..They are both laptops. one acts as a server for a piece of software to the other one.on the "client" laptop I can map a drive to the "server" and browse files through that maped drive etc.I can also ping the IP address of the "server" but I get a timed out when I try to ping the computer name.Server had Macafee firewall, I uninstalled that, and I turned off Windows firewall on both machines.the software needs to be able to ping by name I guess in order to work..
View 2 Replies View Relatedi want to know how to reduce my ping while playing counter strike condition zero online ??
View 1 Replies View RelatedWe've got about 15pcs at work, all on one network. All connect to one switch, and the router connects to the switch so all has internet access. Four pcs has got windows vista on, the rest XP. Yesterday I tuned on the one pc with Vista on, but could not connect to a mapped drive. I checked in the network places, i could see only three pcs, all three xp pcs. I can browse the internet, but not the pcs on my local network, and I can ping the pcs on the network.
View 1 Replies View RelatedOk, I have a ASA 8.4 firewall that I have been working on so long. It was a hassle to configure the object group and nat for 8.4. So, I put two host in both side of ASA to test pinging but I can not ping the outside or the DMZ. I attached my nat config.
View 1 Replies View RelatedI have a network with three vlans: vlan 10 (172.16.10.0), vlan 20 (172.16.20.0) and vlan 30 (172.16.30.0).I want to make sure that clients in vlan 10 can access to vlan 30, but not access to vlan 20.Vlan 20 can also access only vlan 30.i have configured a router on a stick and the acl's, but some how i can't ping from vlan 20 to vlan 30. [code]
View 1 Replies View Relatedwhen we ping from pc in lan 1 to pc in lan 2, what protocols we walk through in request and in response??
View 14 Replies View Relatedcant get online,found that the internet IP ping failed
View 24 Replies View Relatedwhile trying to hookup wireless cant det past gateway ping on test. Iv'e used addresses given to me by net gear.
View 5 Replies View RelatedThe server is on a different network and the desktop is on a another network.I can ping the server but i can't access any drive on the server.
View 1 Replies View Related