Cisco WAN :: 2950 - IOS Software Upgrade
Mar 13, 2008
I have a catalyst 2950 ver. 12.1 EA(48 SI) and intend to upgrade to the latest version of the software. But there have been Four different IOS IMAGE releases before the latest one of 2008. My question is, DO I HAVE TO UPGRADE THE PREVIOUS FOUR RELEASES BEFORE THE NEW ONE OR WILL UPGRADING DIRECTLY TO THE 2008 NEW IMAGE Suffice?
View 2 Replies
ADVERTISEMENT
May 6, 2012
We are in a process to replace our old end of life switches( mostly Cisco 2950's) with some new offerings from cisco. Attached is our current network diagram. Anny merit of using Cisco Nexus switches in this design and also what will be the benifit in doing so. Again I am asking about the specific benefits which I will get in my Network not general benifits of nexus.
View 5 Replies
View Related
Dec 14, 2011
I have a cisco catalyst 2950 switch (flash:c2950-i6q4l2-mz.121-22.EA1b.bin), in remote location with public IP,how to upgrade ios remotely, by that time running configuration will go?how much down time is required and ?
View 7 Replies
View Related
Aug 7, 2012
I own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies
View Related
Sep 29, 2011
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies
View Related
Jun 19, 2012
I am facing a problem to install a ap upgrade lic file on controller 5500. Iam getting the following error:
% Error: License file transfer failed - Error from server: File not found
I have confusion here that when I configure this command from GUI
tftp://172.32.45.22/cmm/standard.lic
What i should use for /cmm/ ????
Let say i have lic. file is on desktop of tftp server computer and I say in this command
tftp://10.12.70.35/??/license file .lic
View 6 Replies
View Related
Sep 28, 2011
We have installed last Network Assistant version, 5.6(3), but we can't add any switch to it.... It says always "Unsopported Device type: unknown".Our switches are all 2950, 2960 and 2970 models.
View 4 Replies
View Related
Mar 15, 2013
in the last days i'm encountering some issue about ping on some 2950 access layer.These ones are directly connect (fiber trunk) to 4500 core switches. Ping response is very high between 200 up to 600 ms for a period about 30-40 seconds, then returns to normal valueI tried to ping every host connected to this 2950 and ping responses are normal 1ms or less.
View 7 Replies
View Related
Oct 6, 2011
Telco provided a BGP connection on MPLS network. When I connect router directly to Telco switch I can see BGP neighbor, so my router BGP config is OK. However, I need to put this router in a diffferent building and want to bring the connection over on a "trunk"; now I loose the BGP neighbor. I'm sure I did this before and it worked OK. I'm trunking between 2 x2950 switches using this config on each switch. [code]
I also configured the trunk as vlan 1214, which is the encapsulation provided by the Telco (dot1Q 1214).
View 6 Replies
View Related
Jan 2, 2013
Is it possible to run VTP V3 on 2950 and 2960 switches. If so what version of IOS supports V3? Our 2960s are running 12.2(25r)SEE1, and 2950s are running 12.1(22)EA4a. Neither of which supports v3.
View 3 Replies
View Related
Sep 10, 2012
Is it possible to upgrade the CSACS-1121-UP-K9 to be a non upgrade part? We were going to upgrade from a Windows 4.x to the above Appliance (version 5.x) but there is now a reason to keep the old Windows version running therefore we cannot give the new Appliance the old ACS's licenses?!So we should have (with hindsight) bought a fresh version of the ACS 5.x rather than an upgrade.
View 1 Replies
View Related
Jan 10, 2013
Im looking to connect up 4 new pcs to network but I don't have enough wall ports. I thought I could plug cisco 2950 switch into the port on the wall and act like a hub. The switch configuration is default and there is only one vlan. How is it that it won't connect. Does it need a crossover cable.
View 3 Replies
View Related
Feb 7, 2011
I am trying to figure out how to setup quality of service on my network. At the moment i have computers connected to the PC port of my IP phone and the IP phone connected to the switch.I want the PC to stay on the default native VLAN and the phone to go on the VLAN 10I am using SNOM300 and SNOM360. I will configure the on the phone the VLAN ID and the priority.From my research, there are two ways that I can go about this on the port that is connected to the phone I canswitchport voice vlan vlan-idorswitchport voice vlan dot1pand then I will have to execute the commandmls qos trust cosmy question is which command do i use to configure the ports, and am I on the right track? Also, this is how I configure the ports that the IP phones are connected to, how do I configure the port that my Asterisk PBX server is connected to?
View 4 Replies
View Related
Nov 13, 2012
What is the difference between the 2950 and 2950c switches? I tried finding it on the feature navigator but I couldn't. And I wasn't able to get anything from the Cisco website either. (I didn't really look through the long PDFs, I'm sure there is a more simple way to find the answer to this that I'm not aware of.)
View 3 Replies
View Related
Aug 3, 2012
I need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
View 1 Replies
View Related
Apr 9, 2013
Bought a used 2950 for CCNA labs. I have no IOS and cannot get a successful transfer via xmodem. In ROMmon after the transfer completes text shows up as gibberish, commands seem to work. Text is normal after I reconnect. Dir flash: doesn't show any sys image, only a -rwx file. I have tried various IOS versions. This was purchased used, so it's possible it isn't working. This is my first time configuring a switch, I might have missed something simple.
View 5 Replies
View Related
Feb 23, 2006
how to enable RSTP in the switch (Let's say in 2950 switch).
Or do you have RSTP running in now-a-days switches?
View 2 Replies
View Related
Dec 27, 2010
I just started configuring my cisco catalyst 2950 switch. Basically im preparing for my CCENT exams my basic configuration is as follows.
-My Laptop is connected to the console port
-I'm connected to the internet via my wireless
-I'm connected to the switch port via my NIC card
View 4 Replies
View Related
Feb 16, 2011
I need to update the software for the switch 2950 we have in our LAN. Its been 6 long years I have not looked at this switch and so now is the time since I have had some issue (ie. Outlook losing connections and once in a while email get send out AGAIN for bazzarre reason)
Anyways, I am looking here for thes software I am abit unsure which software to use via Network Assistant. This is the current status of the switch (Cisco 2950, WS-C2950T-SI, 12.1(22)EA4a - C2950 - I6Q4L2-M ). I want to understand what is the difference between C2950 EI AND SI IOS CRYPTO and web based device manager and C2950 EI AND SI IOS IMAGE AND WEB BASED DEVICE MANAGER and which one should I be using for my switch?
View 2 Replies
View Related
Dec 7, 2011
I have a etherchannel defined between 2 L2 switches using LACP as shown below. The etherchannel works fine, however when I hard code speed/duplex on both ends the etherchannel fails. What is causing this behaviour?
SW02:
interface Port-channel5
interface GigabitEthernet1/0/1
switchport mode trunk
[Code]....
View 6 Replies
View Related
Sep 27, 2011
Am experiencing high output drops o int Gi 46,47,48 2950 int fa 22 23 and 24 are conneced to 3750 Gi 46,47,48 core sw1 3750 is connected to 2950 sw2 and vice versa
View 3 Replies
View Related
Mar 8, 2012
I have several 2950 switches that I cannot get to work with TACACS. I'm using the same config for these that I am using for other cisco switches. [code]
View 1 Replies
View Related
Feb 11, 2012
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies
View Related
Jun 22, 2012
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
View 18 Replies
View Related
Apr 25, 2013
I have a server windows 2008 that I would like to have a nic teaming configuration, the server has two nics, each nic is connected to a different switch. One is connected to cisco 2960 and the other is connected to cisco 2950. I have read here in forums about nic teaming but using the same switch. I have not found using different switch. Is this possible?
View 1 Replies
View Related
Jan 11, 2012
2950 switch has a IOS on flash , but i would like to set the swith like...
1. switch IOS to be loaded from TFTP server .if it fails
2. Loaded from local flash IOS1 , if it fails
3. IOS loaded from local flash IOS2.
does 2950 switch support this feature.
View 2 Replies
View Related
Jun 11, 2012
I have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies
View Related
Apr 15, 2013
Any quick breakdown on the differences between some Network Management software titles. I dont know when you would use each one or what the limitations are of each. [code] I have been looking over the release notes for each product trying to draw some conclusion on which titles support or dont support certain products.
When you would use each and if there are any gotchas or limits to watch out for? It looks like Prime is a paid for product but will any of the free solutions (CNA, CCP, CCA) work with all enterprise level products (2950, 2960, 3560, 3750, 4948, 4900 4500 switches and 1800, 1900, 2800, 2900, 3800, 3900 routers) or do you have to use Prime to get a product that will mange these devices?
View 6 Replies
View Related
Oct 26, 2011
Can't get cisco router and switch to see each other? When I connect the 2620 router to a 2950 switch no link lights turn on. It's the same when I connect any router to either of the two 2950 switches I have. I can connect to both switch and router from a pc using telnet and the router can connect to a regular tp-link switch. I'm a newbie when It comes to Cisco. Here's the running config for the router and switch. There Is no connection when using any of the switch ports to connect to the fa0/0 of the router. [code]
View 17 Replies
View Related
Feb 11, 2012
I've connected a dslmodem/router to a fast ethernet port(fa0/1) on a 2620 router.There is a 2950 switch connected to the other port (fa0/0).I can ping the Internet via the router but and the switch but not from a host connected to the switch.I can't reach the dslmodem from the host pc.I've configured nat(overload) on the router.
View 8 Replies
View Related
Feb 24, 2011
I'm unable to connect to the internet?My university gave us student permission toset up a cisco lab. I hve an 1841 router and a 2950 catalyst switch in a single room. Fa0/1 is conncted to the switch using a 192.168.3.0 /24 network. DHCP is correctly assaigning ip addresses to the switch.
I connected the Fa0/0 port to the wall and used the following command to obtain an ip on the Fa0/0 port: ip adress dhcp. I used the following route command: ip route dhcp. That didn't work so I used the ip route 0.0.0.0 0.0.0.0 Fa0/0.When I run the sh cdp neighbors command I see a multilayer switch that show me connected to the Ga2/26 port with ip:192.168.179.254.I also see that the default vlan is 200 and the voice vlan is 800.
A linksys router is about to let us access the internet. I am able to ping the 192.168.179.254 address from the 1841 router.What am I missing to connect to the internet.I forgot to mention that I successfully receive an ip from the wall. The latest ip I received was 192.168.179.100 /24.
View 24 Replies
View Related
Apr 15, 2013
I have been though the setup a couple of time with no luck pinging one pc to another from vlan 10 to vlan 20. I posted the running configs and some other information from my router and switch. I am relatively new to all of this so if you need me to post more information from the hardware let me know and Ill put it up. There are no firewalls in place and I know the cables are good because I switched them around to make sure. Also when I change the ip on my second machine for vlan 10 I can ping from one pc to the other but when I try the same for vlan 20 I get nothing.
**From my 2950 switch**
Current configuration : 2825 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
[code]...
View 5 Replies
View Related
May 24, 2006
I am trying to implement IP SLA. Can I implement it on layer2 switches?
View 5 Replies
View Related