I just started a new Position and they have CATos still runing on some of there 4506 and 6509 switches. I amy trying to come up with a plan to upgrade the switches to IOS but I dont know if they will take it or not. I know I need to get flash Cards to hold the IOS but i need to make sure that I get the right IOS for the Switches.
View 1 Repliescan i use vb scripts or bat files to execute cli commands on 6509 catos 7.6?any useful links or scripts?
View 2 Replies View RelatedIf we have catos 6509 and MSFC and we need to connect new building with L3 I want to Do static route between two network i need to but ip in interface of switch should I but this ip on catos or MSFC,
Switch(config)# interface fastethernet 2/1
Switch(config-if)# ip address x.x.x.x x.x.x.x
In catos if want want do like above command what is the command .
I need to replace a faulty fan unit on the catos WS-6509 switch. this Catos switch does not support show inventory so any other catos commands which will show me this part id?
View 2 Replies View RelatedWe are in the process of migrating to the ASA service modules on both our 6509E switches from our current FWSM. We have used the Cisco conversion tool and applied that to the service module. When viewing the context in ASDM we are unable to view the object names in the right hand pane.
On the FWSM I would see the following under Network Objects:
Network Objects
- JQ-Test
- JQ-Test2
- JQ-Test3
Network Object Group
+ JQ Group
- JQ-Test
- JQ-Test2
- JQ-Test3
Now I have run the conversion tool and applied that to the ASA's I now get the following results.
Network Objects
- 10.1.1.1
- 10.2.2.2
- 10.3.3.3
Network Object Group
+ JQ Group
- 10.1.1.1
- 10.2.2.2
- 10.3.3.3
I am aware that the naming convention on the ASA's are different to the FWSM as you can no longer use the "name 1.1.1.1 JQ-Test1" format but I was hoping that the conversion tool would do this for me.
Is there any way I can get the names of the object back without having to script something that takes the old FWSM format and convert it into an ASA format?
I have seen links out there for a conversion tool to convert commands on a Catalyst type switch (6509) to newer IOS type switches(4500-e) switches but they all error out on me on a 404. Any link where I can get this conversion tool?
View 1 Replies View RelatedI am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
a 6509 and a 4506 with 2, 1gb interfaces in a portchannel. Bring it up and everything is fine. Save the config and reload either switch and the interfaces stay in Not Connected state. Either doing a No Shut or a physical unplug the SFP and plug it back in will bring it up with no issues. Interfaces do not go into Err Disabled state they stay in Not Connected like there is no fiber plugged into it. No error mesages in the log. The Just the Interface is now up.Both are running very new code,
6509 - s2t54-ipservicesk9-mz.SPA.150-1.SY1.bin ( 15.0.(1)SY1 )
4506 - Version 03.02.00.XO
I'm currently in the process of doing a bandwidth analysis on 2 WAN links at my current HQ / remote sites. The topology is pretty straightforward, two 3845 routers at HQ, and two 3845 routers at my remote site, both with P2P DS3 interfaces between them. From each router we then connect directly into a 6509 at the HQ, and a 4506 at my remote site where we are using equal cost load sharing (EIGRP) to split the load / give us redundancy between the sites.
I'm just looking for a good test for how well the circuits are performing. I've done some basic file transfer tests, but they're only showing about 4MBPS, which seems quite slow. I also know that this isn't a true measurement because there are amny different factors involved, like hard drive write speeds, network congestion, etc, that may influence the test.
how to setup this old switch 4500. It is running CATOS and I want to make sure that when I connect it to the network it doesn't create a loop since it has to be compatible with other vendors, not just Cisco.I don't have anything connected but these are my concerns: It doesn't show my lacp-channel (i believe this is what is used to for Teaming network cards), it doesn't show my trunk ports.
TestSwitch> (enable) show lacp-channel
No ports channelling
TestSwitch> (enable) show trunk ?
detail Show detailed information
<mod> Module number
<mod/port> Module number and Port number(s)
[code]....
I have a new 6513 with 2 sup32's with IOS. This chassis will replace a working 6513 with 2 sup2's with CatOS.I need to pull the running config from the CatOS chassis and make it work on the IOS chassis. i can do this manually but was wondering if there are any trade secrets on doing this.
View 3 Replies View RelatedI have a 6506 with SUP1, no MSFC running CatOS.
Module 1: Removed
Module 2: WS-X6K-SUP1A-2GE
Module 3: WS-X6348
Module 4: WS-X6348
Module 5: WS-X6408A-GBIC
Module 6: WS-X6408A-GBIC
However, it doesn't seems to be able to bootup properly. Could this be an hardware issue? What should I do?
I have a client who is changing their management IP scheme as a bridge to replacing equipment and much of the old equipment (Catalyst 4000) is running CatOS and I am a bit weak in CatOS. The existing Management IP is setup as follows:
set interface sc0 1 192.168.252.209/255.255.255.0 192.168.252.255
set ip route 0.0.0.0/0.0.0.0 192.168.252.1
What we want to change this to is as follows:
set interface sc0 110 192.168.197.209/255.255.255.0 192.168.197.255
set ip route 0.0.0.0/0.0.0.0 192.168.197.1
The devices are spreadout over a large area and visiting each device is almost out of the question due to a time deadline I was wondering if I run this set of commands will this allow me to keep a remote session (SSH) running until the change is complete?
set ip route 192.168.197.0/255.255.255.0 192.168.197.1
set interface sc0 110 192.168.197.209/255.255.255.0 192.168.197.255
set ip route 0.0.0.0/0.0.0.0 192.168.197.1
We are implementing NAC in our environment and unfortunately still some of our obsolete 6500 switches are running CATOS, the current (cat6000-sup2cvk9.8-6-4.bin) image does not support some of the commands related to NAC implementation. Therefore, I would like to urge you to provide me the 8.7 image which supports all the NAC related commands and will be easier to finish the long pending assignment.
We are in process of replacing the obselete hardware but that will take time.
So, 8.7 K9 CATOS image required.
I have to upgrade two Cisco Catalyst 6509E from Catos to IOS. I would want to know the requirements hardware or software for upgrading. Which are the recommended images I must download? From cat6000-sup32pfc3k9.8-4-5 to the latest stable version of IOS, is it recomended to pass to another previously version before?
I have viewed the following links,[URL]but, it doesn`t mention anything about that. The image below is the result of the "show version" command of one of our Cisco Catalyst.
WS-C6509-E Software, Version NmpSW: 8.4(5)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Aug 3 2005, 13:13:36
[code]....
I am trying to Disable Telnet and enable SSH in CatOS for 6500 .
View 12 Replies View RelatedI need to convert configuration from CatOS on 4006 to IOS on 4510. I am unable to find the conversion tool.
View 5 Replies View RelatedI am trying to find a command for dhcp snooping rate-limiting on a CatOS. The PFC card is PFC. PFC3B is said to support that command. But there seems no this command.
-6k> (enable) sh ver
WS-C6509-E Software, Version NmpSW: 8.4(5)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Aug 3 2005, 13:26:46
[Code] ......
Up time is 1183 days, 1 hour, 41 minutes
I have a new 6513 with 2 sup32's with IOS. This chassis will replace a working 6513 with 2 sup2's with CatOS.I would like to convert my CatOS running configs to IOS, and I know there used to be a tool for this.
I have searched around and found many broken links to an old Cisco tool to convert my former configs, is there any way to get this tool today? I have tried over 20 links and not been able to find a working one yet.
I have a question. I have a 6500 with two supervosrs and they both have CATOS. One of them failed and I need to replace. As long as the hardware is the same does the CATOS have to be indentical or can this be different.
View 4 Replies View Relatedhow to convert configuration catos on 6500 to IOS image.
View 3 Replies View RelatedI have a core switch Cisco3750G with 4 SFP slot populated with GLC-SX-MM module.Now in these 4 fiber GLC-SX-MM modules 3 are connected to 3 floor switches which are having the same GLC-SX-MM.Each link is configured as a TRUNK and allowed only that floor VLAN and working fine.Now the 4th GLC-SX-MM module has to be connected to a single desk top PC using a FIBER to UTP convereter,which is SC to UTP .Now patch pannel is LC ,I used a LC to SC fiber patch cord,but link is not coming up,in this situation if I used both side SC convereter then link is up.
All 4th GLC-SX-MM modules are checked and it is working fine.Only the forth floor link is not coming up,if I use the UTP to Fiber SC type connector in the CORE switch for teh 4th Floor then it is working.How to resolve this issue,Whether I need to use the UTP to Fiber LC type convereter in the fourth floor instead of SC type converter,logically when I use the LC-SC type patch cord and connecting to SC type converter it should work.
I have 8.2 configuration that works:
global (inside) 1 192.168.1.1
nat (outside) 1 access-list Servers outside
static (inside,outside) 10.16.0.0 10.1.0.0 netmask 255.255.0.0
[Code]....
It is remote monitoring ASA, so I need to nat user networks (10.1.x.y, 10.2.x.y) to something that I can use (10.16.x.y, 10.17.x.y...)
Also, since it my device, I have them configure snmp and syslog server on client's network to use 192.168.1.1, so I have dynamic NAT for two SNMP servers and static NAT for one of them (which is syslog server).
create 8.4 version, so I can apply it? I tried few things, packet tracer shows that they are NATed, but I have only Denc packets, because hosts see request coming from my public IP...
I am planning to get the unicast streams from different 2-3 sources over internet, and I am doing NAT for port-forwarding all those unicast streams to a one private IP. Attached is the setup for your understanding.Setup: - Both unicast streams will be hitting to One Public IP (3.3.3.2) on UDP/TCP Port 1234, 1236 & 1238 only & the same ports need to be forwarded to natted One Private IP (10.10.10.4)
1)NATTING these 2 unicast streams into one private IP(10.10.10.4) by checking Source & Destination based IPs and ports, but in below configuration I cannot achieve on checking Source & Destination based IPs and ports
Router configuration:-
interface GigabitEthernet0/0
description ***Connected to Internet ***
ip address 3.3.3.2 255.255.255.252
no ip redirects
no ip unreachables
[code]...
We are about ready to embark on moving all L2L and network extensions (Cisco ASA 5505s) from the Cisco VPN 3060 Concentrator to a Cisco ASA 5520. We would like to know if there is a simple method to doing this such as a converter? Also, are there any lessons learned? We are running 8.4.3 so we know that NAT configuration has differed. Can the configuration from the 3060 be modified in anyway in configuring the ASA?
View 4 Replies View RelatedI am in the process of migrating a production firewall from PIX 6.3 to ASA 8.4(2). This is going to be a complete firewall rebuild and I will not be upgrading the configs because they have become out of date and very bloated. I am in the process of converting the NAT commands.[code] I am hoping these commands would be enough to replicate the previous functionality. I removed all the static identity NATs because NAT control is no longer in place so those rules are not required. Additionally I didn't re-create the rules that had NAT ID 0 or 1 because it didn't look like they were doing anything. correct way to do the static NAT commands at the bottom.
View 3 Replies View RelatedAs previous posters may have noticed i have been given the task of moving the ACS from 4.0 to 5.3 which turns out to be considerably different. Sadly i have nothing to test with at the moment so am trying to work it out as best i can before the abbreviated period of cutover begins.
I have a Service Desk group setting in 4.0
Under groups i have the group settings and down the bottom i have the following -
(ticked ) Wireless-WCS HTTP
(ticked ) Custom Attributes
Then in the box -
virtual-domain0=CRUK
[Code]....
Access Policies/default device admin/Authorisation Create a new Rule Add the correct AD group in compound condition AD-AD1 attribute ExternalGroups value static in NDG:Device Type - reference the WLC (previously created as device type with ip address) Then in Results reference the above shell profile - Service Desk.
I'm trying to configure an LACP channel trunk between a CatOS C6000 and a Dell PowerConnect.
I use mode active in both sides and it works great.
But, when I connect a Catalyst 3750X to the Dell PowerConnect the channel between C6000 and PWC shutdown:
2013 May 16 09:08:20 CEST +02:00 %SPANTREE-2-CHNMISCFG: STP loop - channel 5/19-20 is disabled in vlan/instance 20
2013 May 16 09:08:20 CEST +02:00 %SPANTREE-2-CHNMISCFG2: BPDU source mac addresses: 00-04-6d-43-a4-e2, 70-ca-9b-27-46-99
Customer of mine has 20 AP AIR-BR1310G-E-K9. No controller installed. He use them as Autonomous AP.
Right now ##he wants indroduce a WLC. Due to that every single AP must be converted in LAP AP.
is this action free of charge ? Nedd I SMARTENT COVERAGE ?
I know that configuration in 8.2.x and 8.4.x is different in terms of NAT and object groups.
I just want to know is it possible to do a direct upgrade from 8.2.3 to 8.4.x ?Secondly, will ASA automatically convert all the configuration from 8.2 to 8.4 format during the reboot after the upgrade?
I am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
I used speed test and got 50 mega bits per second. I tried re downloading tf2 and i was getting 80 kilo bytes, and I am using windows 7. Doesn't 8 mega bits equal 1 mega byte?
View 2 Replies View RelatedI need to get a connection through a 3 storie structure.
On each floor, I have a cluster of servers set up. Conventionally, I would thread cat6 cables through the building but due to various reasons I cannot do that.
On the ground floor there are 2 ground lines which project a wireless signal.
I'm wondering, is there some way I can convert the wireless signal into an ethernet line? Perhaps through some kind of interfaced adapter. I've thought of buying a throwaway laptop and bridging the connections manually but I'd prefer to avoid that option if there are feasiable alternatives.