Linksys Wireless Router :: EA4500 - Can't Run Setup CD On Mac Running OS 10.8.2
Feb 5, 2013I can't run the setup cd on my mac running OS 10.8.2.
View 2 Replies
ADVERTISEMENT
Linksys Wireless Router :: What Frequency Band Running EA4500 For 5 GHz
Jul 4, 2012I would like to know on what frequency band running Linksys EA4500 for 5 GHz because in Israel only allowed frequencies from 5150 to 5350 MHz.
View 1 Replies View RelatedLinksys Wireless Router :: Cisco 4500 Configuration Without Running Setup CD?
Jul 28, 2012My issue is that when trying to run the setup software for my new cisco 4500 router, an error message comes up which states that the new mac operating system 10.8 aka mountain lion is not supported. so now i had no choice but to leave my network unprotected as i cannot run setup. I was just wondering if there was another method by which i can configure the router without running the setup cd.
View 3 Replies View RelatedLinksys Wireless Router :: EA4500 - Setup Several Devices In The Parental Controls To Be Blocked Always
May 13, 2012I setup several devices in the Parental Controls to be blocked always. These devices are still able to connect to the router. I tried rebooting the router but the problem persists. I have two laptops and two iPod Touches that can connect regardless of the access restrictions.
View 5 Replies View RelatedLinksys Wireless Router :: EA4500 Scan Setup / Printer Goes Online Only While It Prints Pages
May 2, 2012Just finished the setup for Canon MP780 USB printer to work with EA4500. Printer goes online only while it prints the pages. When I try to scan the document with MP Navigator it cannot communicate with the scanner as printer is essentially offline. How to setup the printer in order to perform the scan of the documents?
View 2 Replies View RelatedLinksys Wireless Router :: EA4500 Setup On Corporate Network For Wireless Access?
Jun 19, 2012I have a Linksys EA4500 setup on my corporate network for wireless access. I have enabled the guest network and from all I can tell it's on a seperate subnet from my internal network like it should be. 192.168.x.x My internal is on a 10.x.x.x network. I conenct to the guest network using a laptop and I'm prompted for a password to get to the internet, which I like. The one issue I'm seeing is when I'm connected to the guest network I can still do an RDP session to internal resources. How is this possible if the guest network is on a seperate subnet?I take a laptop which has not been joined to my domain, connect to the guest ssid, and then open an RPD session and enter an IP address for an internal server and it connects. Is there a setting to keep this from happening
View 6 Replies View RelatedCisco Linksys EA4500 - Unable To Setup Router
May 11, 2013I just bought a new router for my home network. It is the Cisco linksys EA4500. It looks great and is rich with features but I just wish I didn't buy it!
My old wireless router started to have its wireless signal very weak, hence this new linksys router. When it is time to setup the router, I just did what was supposed to be done(which is very straight forward, just a matter of choosing pppoe and inputting a username and password) and went ahead to test the internet connection which didn't work! Upon inspection, I discovered that the lights on the internet port on the router(WAN port) didn't turn on at all as if the cable wasn't connected. I quickly checked all connections and to kill any doubt I reconnected the cable to the old router to make sure it is working and it worked. So there is nothing wrong with the cable!
I tried everything one can think of to no avail. The only conclusion one would draw from this whole scenario is that the new router is bad. So, I took it back to the shop I bought it from and before giving me another one, he said he will test it out and I said okay. Surprisingly enough, it just worked !!! Don't ask me why but it just did work beautifully, although at my house if you plug the cat6 cable(that you know for sure has internet) into its internet port, it won't even turn its lights on.
Linksys Wireless Router :: Set Up EA4500 Without A Computer?
Sep 2, 2012I've looked all over the internet for this and can't find a definate answer. Waited for live chat and got kicked before I got to talk to someone... Just sold my computer and the plan was to buy a newer mac but we've been getting along fine without a computer with just using our iphones. So my question, I see that Cisco has the Connect Express app for the iphone, and I've read about all the features it has like changing settings, router features, etc. But I can't find anything on using the app for the initial set up of the router. I'm currently on an older linksys router (set up before we sold the computer) but it's time for a needed upgrade.
View 3 Replies View RelatedLinksys Wireless Router :: Using An External HDD For EA4500?
Apr 30, 2012I got my ea4500 all set up. never had a media servor or anything like that, figured this would be an easier way. when i hook up my exteral i can find it but i can only view the files in windows media player. how can i just browse the folders manually? WMP doesnt let me browse the folders as they actually are on the HDD which is such a pain in the **bleep**.
shows a device in "network infrastructure" but it says problem sending command to the program when i click that. i dont want to have to view the HDD in WMP as a media device...
Linksys Wireless Router :: EA4500 Won't Obtain IP From ISP
May 12, 2012My new EA4500 (fw ver 2.0.36) won't obtain an IP from a Brighthouse TM502G cable modem. The EA4500 replaced a functioning WRT54G which would obtain an IP from the ISP. I've tried upgrading firmware and have used both straight-through and crossover cables between the EA4500 & TM502G to no avail. The EA4500 would issue IPs to it's clients, but not obtain one from it's TM502G. At the moment, all 3 are daisy-chained together with the old WRT54G in the middle in order to make the EA4500 work. Both WiFi and LAN ports function in this configuration.
View 1 Replies View RelatedLinksys Wireless Router :: EA4500 Only Uses 2.4 Ghz Channel?
Dec 19, 2012I downloaded and installed inSSider for Windows and, under the 2.4 Ghz tab, I can clearly see the Router SSID, on Channel 6, exactly as configuredbin the Router. However on the 5 Ghz tab, nothing? I can see Channels 36, 40, 44, 48, 52 and so on BUT no trace of any wireless signal here?I carefully reviewed the wireless settings options and it is indeed enabled.
View 1 Replies View RelatedLinksys Wireless Router :: Connecting EA4500 To Another One?
Feb 4, 2013Connect my primary router EA4500 to another EA4500?
I tried and followed the steps provided here but it doesn't work at all for the Xth time already.
The first router installed and ran flawlessly in minutes. The second one has failed to work in bridge mode for 3 hours now.
Linksys Wireless Router :: Get Forum For Just EA4500?
May 20, 2012Can we get a forum title just for the EA4500?
View 1 Replies View RelatedLinksys Wireless Router :: How To Use EA4500 As A Bridge
May 15, 2013In my apartment, I can receive the wireless signal of free scholl wireless, which is accessable without user name and password. Although the signal is not good, but we used to use a router EA3000 to relay the signal. Now my roommate is leaving with this this router. So I bought EA4500 and try to do the similar job. However, I find that the configurations on 192.168.1.1 are different between EA3000 and EA4500. Many options cannot be found in the EA4500 page, such as the wireless client.
View 4 Replies View RelatedLinksys Wireless Router :: Can't Find EA4500 At 25%
Apr 23, 2013I recently got an EA4500 from a friend and when I tried to run the Cisco Connect CD on my MacBook it gets to 25% and then stops and says it can't find a router. I've reset, powercycled, unplugged, plugged, searched, and searched but I cant seem to get it to find the router.
View 3 Replies View RelatedLinksys Wireless Router :: EA4500 Won't Allow Wake On WAN
May 6, 2012I'm hoping to get this router to allow WOL (actually wake on WAN) but it seems to be blocking the necessary broadcast magic packet even though the settings appear correct. It's not critical, but the reason is this: I'd like to shut down the home PC, but when necessary be able to start it up and use a VPN to access any info I need remotely.
From within the LAN, I can verity that WOL works. I have NIC and PCI WOL enabled in the BIOS. The NIC (a Marvel Yukon Gigabit) has WOL enabled as well as "allow this device to wake.." using magic packets under power management. The target machine's local IP is reserved through the EA4500 DHCP Reservation table. Just for troubleshooting, I opened port 9 in windows firewall. More importantly, I have ports 7-9 forwarded to my target LAN address. Single port forwarding... it just has been less reliable (?). I'm using a mask of 255.255.255.128 in order to enable broadcasting on .127 at some point as it seems it must be necessary. Broadcasting on .255 is not possible, despite some workarounds I found on the web. EA4500 firmware is the latest, 2.0.37. I have turned off the multicast filter and the anonymous internet filters under the security tab.
So, with these settings, I can WOL from inside the network no problem either targeting the LAN address, or by using a dyndns address. So far so good.With these same settings, I can go to WAN using Depicus or the Cloud Connect Pro app over 4G on an iPad. With all these same settings, WOLsniffer confirms the magic packet still getting through over WAN (obviously using the dyndns address). Even better, I can shutdown the target PC and STILL wake it up within a few minutes from WAN. Let me restate that! Wake up over WAN works, but only for the first few minutes after a shutdown.
However, if I wait 20 minutes or so, WOL stops working. If I change the port forwarding to .127, not only does it not work, but WOLsniffer will fail to see the magic packet. My conclusion is that the ARP table is getting purged, which is undertandable, and so the target LAN address isn't in memory. However, frustratingly the EA4500 will not broadcast no matter what settings you use. This limitation is undocumented, and counterintuitive since the software allows you to disable multicast filtering and does not notify you of an error when forwarding to xxx.xxx.xxx.127 with a 255.255.255.128 mask.
Linksys Wireless Router :: Enable WDS On New EA4500?
May 31, 2012How do I enable WDS on my new EA4500 ?
View 3 Replies View RelatedLinksys Wireless Router :: EA4500 Wake On Lan?
Jun 11, 2012Was thinking to buy this router but I am not sure if it supports magic packets in order to use wake on lan on PCss and NAS
View 3 Replies View RelatedLinksys Wireless Router :: Ea4500 - Can't Exactly Set Up Wifi
Mar 3, 2013I really want to have a password on my wifi, but I cant control it when all it keeps asking me is for a CD I have a EA4500
View 1 Replies View RelatedLinksys Wireless Router :: FTP Server On EA4500?
May 11, 2012Using the FTP server built into the EA4500 firmware. I can get the FTP service to work from some computers outside my home network, but when i try to access the service from a PC within my home network i am unable to connect to the server through the WAN address.
View 1 Replies View RelatedLinksys Wireless Router :: EA4500 Disconnects Sometime
Oct 23, 2012I bought 2 weeks ago a Linksys EA4500 after searching the best Wi-Fi Router all over the net... I choose this cos all over people writed that it was amazing, fast a nd very good coverage all over the house.
Before I had a Buffalo AirStation Dual Band, wich worked perfectly. But since I have several tv and a central NAS whit all films in MKV, I wanted the BEST product for my system, so I choosed Linksys EA4500!
Well, the result is that (when it works it is greate) but sometimes it disconnects and I have to restart it... And second thing that makes me MAD is that the coverage in my house is WORST!! Before my Wi-Fi was present in all the house, now in some parts doesn't work! The position is the exact same of the Buffalo, so it's not a problem of position... I tryed also a router of 40€ and it has a better coverage! How come? how is it possible that a person pays more than 200$ (in Italy it costs 185€) and the result is so BAD??? I'm totaly freak about Linksys now.
Linksys Wireless Router :: Possible To Downgrade New EA4500
Oct 20, 2012I'm in the process of wanting to upgrade my wireless network but I'm not really agreeing to the Cloud Connect, I don't need to have my settings on the internet. I want to manage everything on my own. I've found the following link on the community to be able to put the classic firmware before the cloud connect feature {URL}.
My question now is : If I buy a brand new EA4500, will it still be possible to downgrade to that firmware? No problem with this one? I'm hoping Cisco will continue to publish bug fixing if any to this classic firmware.
Cisco Wireless :: SAP1602i - Setup For AP Running In Autonomous Mode For Clients?
Apr 25, 2013I am trying to have a setup where the AP running in autonomous mode also act dhcp server for the wireless clients.The only thing is that the vlan is switched across to the wired network.
So basically i am having 2 vlans, one for mgmt and other for data (for wireless clients) and both vlans are trunked to the switch.
[CODE]...
Linksys Wireless Router :: EA4500 2.4GHz Not Transmitting
Apr 3, 2013I purchased a EA4500 and at first I could connect to it through its default ciscoxxxxx ssid on my laptop which is 2.4GHz only. I upgraded the firmware using the PC utility and now I can't find the 2.4GHz SSID no matter what settings I do. I've disabled and enabled it multiple times, changed it to have no security or with security and enabled and disabled it and renabled it. Nothing seems to work, but for some reason the 5GHz side I can connect to using a 5GHz device. I've also tried disabling the 5GHz side, but still no 2.4GHz.
View 4 Replies View RelatedLinksys Wireless Router :: Unable To Connect To EA4500
Oct 2, 2012Just purchased a ea4500 router. Have setup multiple computers/devices already and works great. This computer (HP dv6000 running Win Vista home prem) however will not connect to the internet. It states that it is connected to the router (computer sees router), using the cloud connect app on my iphone i can see this computer, but will not allow access to the internet (local connection only). It works fine with the wired connection. When attempting to use the cloud connect software, it says it was unable to complete the install. Have attempted trying while connected by wire as well, same result. Have deleted the wireless connection and allowed software to find connection, still same result, cannot install. Wireless worked perfectly with previous router (WRT54G) three days ago.
View 6 Replies View RelatedLinksys Wireless Router :: Cannot Reach To 450 Mbps With EA4500
Feb 8, 2013I have a new EA4500 router and I cannot configure it to reach the 450 mbps that is supposed to get.
I have it configured as follows:
Dual Band- 2,4 and 5 GHz
2,4 in 20MHz only - 5 GHz in 40 MHz only
2,4 Mixed - 5 Ghz only N
WPA2 personal in both
Channel - automatic (both)
I have checked that the 5 Ghz network can only use 4 channels: 36, 40, 44, 48. Where are the channels up to 100 (or more)? How to get all the power of the router?
Linksys Wireless Router :: EA4500 How To Increase Range
Apr 26, 2012I just installed a new EA4500 and the range is terrible. How can I increase it?
View 1 Replies View RelatedLinksys Wireless Router :: EA4500 And PS3 Drops Connection
Jan 28, 2013I had a WRT54G2 router and began having trouble with my PS3. It would connect for a few minutes then it would lose the internet connection. I thought maybe it was the router so I have the EA4500 now. The same problem is still happening. I connected all of my other wireless devices to the EA4500 with no problems. The PS3 connects and signs me in and then two or three minutes I'm disconnected. I called Sony and Cisco for assistance but in vain. The PS3 is showing my network has nearly 100% signal strength so that isn't a problem
View 4 Replies View RelatedLinksys Wireless Router :: EA4500 Performance Is Very Poor
Aug 24, 2012I recently purchased an EA4500. It started out working really well, but recently I noticed that my speed on my iPhone and iPad has dropped significantly. When I'm in my office where the router is set up, I'm getting around 15 to 20 mb download speed and 5+ upload speed. When I go to my living room about 40 feet away my speed drops to 1mb down and less than 1 up. I expect to see a drop in my performance the further away I get from the router, but this seems really unacceptable to me.
View 1 Replies View RelatedLinksys Wireless Router :: Packet Degradation With EA4500?
Dec 19, 2012I am bridging my NetComm router to the Linksys EA4500 and it is giving me only 8MBps whereas the line speed is 14MBps. I have tried to connect directly to the netcomm by disabling the EA4500 and I am getting 14MBps. Any way to increase my speed?
View 3 Replies View RelatedLinksys Wireless Router :: EA4500 - Can't Login - Get 502 Bad Gateway
Mar 2, 2013I can't log into the router. Get 502 Bad Gateway - Model EA4500; Have a USB Drive connected to the router.
Power-off and Powered-Back on - no change.
Linksys Wireless Router :: EA4500 - Connecting To Second Belkin?
May 13, 2012I would rather have wireless to wireless . Like I said I have a new EA4500 trying to extended my wireless connection to my back yard still having the same trouble of small to no signal, I have a Belkin N+ Ver.2 that I had been using with the same trouble. I would like to connect the belkin N+ to the EA4500 to extend my wi-fi to my back yard and back half of my house.
View 7 Replies View RelatedLinksys Wireless Router :: Difference Between Ea4500 And Ea6500
Oct 5, 2012linksys ea4500 vs the linksys ea6500? is there any real difference?
View 2 Replies View Related
