quick question regarding a 3G access via a cisco 881G i have a partner sim card (with the same number as the one in my mobile) iserted into the router.now i have the problem that my mobile is unreachable (line busy), is there a way to use both sims at the same time?what do i have to change in the router configuration?
View 1 RepliesWe have both DSL and 3G connection to the 881G and both are up and running.There is a NAT for easy vpn device (10.10.10.2) on this router and currently pointing to DSL interface IP (206.206.206.9) ********ip nat inside source static 10.10.10.2 206.206.206.9 extendable*********
My current requirement is that NAT for easy vpn device should work on 3G if DSL link down.So how we can achive the NAT redundancy. Even when I removed the above NAT and pointing to Cellular0, I am not seeing any translations.
I try to make working a 881G router with integrated 3G router (cellular 0) with Bouygues or Orange, but I don't found any working configuration
View 2 Replies View RelatedII have a 881g conecting fine with 3G via cel 0, I Can not ping fx 8.8.8.8 or 4.2.2.2 from cli, bur from Lan everyting World fine.
View 19 Replies View RelatedHave customer that we need 3G at new location. Their company is an AT&T customer.So we have got from distribution a 881G and it has a PCEX-3G-HSPA-US card with it.What do you do or need to get AT&T service on this card. You call AT&T they don't know what your talking about if you say Cisco 3G card?I don't see a SIM slot which most AT&T device have a SIM card?Is there somewhere special you have to call for these to get service? Any checklist for ordering and also configuring for AT&T?FYI, we will do DHCP with it and it will be our backup ISP on and ASA if the primary internet goes down. We will just use a 172.30.x.x addressing between the ASA Outside-Backup interface and the 881G.
View 1 Replies View RelatedI've been asked to configure an 881 with a Verizon 3G backup connection as a backup to the FE4 primary WAN connection. I've been unable to get any connectivity through 3G, and in most cases, as soon as I try to configure 3G, I lose connectivity through FE4.Currently, I don't even have FE4 connected. I'm just trying to get the 3G connection working, so then I can take it back to the office and have a functional 3G backup connection. [code]
View 1 Replies View Relatedtoday I received a Cisco Router 881G with PCEX-3G-HSPA-G for a customer that ordered a Router with the feature to send/receive SMS and to remotely active the 3G Internet connection through SMS. I believe that the router that meets this requirement is the Router 881G that I received today. In particular, the model is:
CISCO881G-K9
Now, I installed the router and configured the 3G link that is working properly BUT all the commands related to the SMS are completely missing. In particular, I miss the command:
cellular gsm sms send
gsm sms archive path
In the following documentation I see that these commands should be available: [URL]The fact that these commands are missing sounds very strange to me since the documentation is pretty clear. Do I need to activate any license? I also upgraded tha router to the last version...
Here it is the show version of the Router:
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sat 24-Mar-12 00:00 by prod_rel_team
ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
[code]....
i have a 881G and an IP SLA icmp configured. (ip sla 1). I can get the status of it by the OID:
1.3.6.1.4.1.9.9.42.1.2.10.1.1.1
But, on the same router i have a track 1 for the SLA 1 and a track 2 monitoring track 1 with threshold . What i want, is to get the OID of track 2 so i can get the status of it. Which OID is that?
an external Antenna for a 881G? We're using AT&T.
View 4 Replies View RelatedBelow is the config has done on my 881g but the dual NAT failover is not working.I have a easy vpn over NAT (easy vpn firewall: 10.10.10.2 behind the router).
1. After completed the config, I shut down the FastEthernet4, cleared the nat translations, found that nat translations are happening on to Cellular0 with error ( Incomplete ESP translations: 0 esp_conn=0x85A91FF0, hanging off nat entry 0x85A7D1D0)But still the easy vpn is not up as I am not able to ping the remote devices.
2. If I reboot the router then the nat translations are happening with no above error and easy vpn is up and I am able to ping the remote servers. Below is the config, what needs to be done to achieve the NAT failover and easy VPN up.
interface FastEthernet4 bandwidth 2048 ip address 206.206.206.2 255.255.255.240 ip flow ingress ip nat outside ip virtual-reassembly duplex auto speed auto interface Cellular0 ip address negotiated ip nat outside ip virtual-reassembly encapsulation ppp dialer in-band dialer string gsm dialer-group 1 async mode interactive ppp chap hostname. [code]
We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
View 4 Replies View RelatedI am receiving trace back logs in the 881G with 3G module. And after reload, the router is going to Initial Config. mode. What the latest IOS is?
Current IOS I am using is c880data-universalk9-mz.151-1.T3.bin. Any better IOS for complete efficient use of the PCEX-HSPA-G Module ?
I have an issue regarding using cellular interface on cisco 881G. The 3G module is Aircard 504. SIMcard is working on other devices, it have obtain IP address from mobile operator. But on cisco881G it doesnt work.
Here is config:
cellular 0 gsm profile create 1 m2m
chat-script 3G "" "ATDT*98*4#" TIMEOUT 30 CONNECT
interface Cellular0
[Code].....
I have a Cisco 881G with PCEX-HSPA-3G card for which I have successfully configured for internet. As the above one has come to end of life, we got the replacement 881G with embedded 3G modem.
I can't get Cellular 0 to use ppp encapsulation:
Router(config-if)#encapsulation ppp
Cellular0: Only SLIP encapsulation supported
Router(config-if)#
[Code].....
I've been already purchased current cisco device (881g-k9),my vendor told me that there is possible to actrivate adipservices license on this router (i need encryption).i'm waiting now for license from my vendor .but for now i tried to activate trial adv_IP lic and got no success on it.So question is there possible to activate AdvancedIpServices license on this router?
View 3 Replies View RelatedCan Cisco 881G cellular interface (Modem Firmware Version = K2_0_7_19AP C:/WS/FW) work with r-uim cards? I can't find correct answer in documentation .
View 2 Replies View RelatedI would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200
ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4
ip address dhcp
no shut
duplex auto
speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1
ip address 10.73.0.1 255.255.255.0
ip helper-address 192.168.140.13
ip tcp adjust-mss 1400
no autostate
ip sla 100
icmp-echo 10.64.4.15 source-interface Vlan1
tag 3G Keepalive
frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
I have Cisco 881g with 3g.I can;'t find any documentation about sending USSD requests from 3g module.is it possible to send USSD request ?
View 0 Replies View RelatedI've been trying to configured Websense urlfiltering using ZFW feature on my Cisco 881G router. The router is running on IOS 15.0(1)M with Advanced IP Services. And I have confirmed it supports urlfilter feature.
This is what I tried to accomplish but IOS version 15.0x seems to have different command set.
-----------------------
class-map type inspect httptraffic
match protocol http
parameter-map type urlfilter param
server vendor websense 10.20.30.40
[Code]...
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies View RelatedCan any explain this topology for me and how it works ? I don't understand the necessity of defining tow PVCs .
View 2 Replies View RelatedI want just want to know on how to add NAT inside and outside ip address.
For instance:
Original Address = 119.xx.xxx.257 (8138)
Translated Address = 119.xx.xx.28 (8138)
On the example above, I can access my web application by typing www.wesbite.com:8138
The settings above was configured by the previous administrator and unfortunately I dont know how to configure same thing as he did.
Now, I made new web application and set it to port 8139, so I should be able to access it by typing the www.wesbite.com:8139
In order to make it accessable on the internet, I should make configuration first on the router via NAT, and I dont know how.
Also, I tried to edit NAT configuration via Cisco SDM (Secutiry Device Manager)
Cisco SDM>Configure>NAT>Edit NAT Configuration
I clicked Add button but nothing happens, even clicking Edit and Delete button
I have an LMS 4.1 where sys log reports available for all the reachable devices on the network. All the devices were configured with the command "logging host <LMS_IP_address>".
The problem is that the report on LMS are shifted 2 hours from the clock displaying on the devices ("show logging" on any device).
How can I check the NTP configuration of LMS? Is it supposed to use the NTP configuration of the operating system (Windows Server 2008)?
Just trying to find my way through the new NAT configuration in later version of the ASA OS but having a few issues.
View 7 Replies View Relatedi have the asa5505 with asa8.4.5 and asdm 6.4.2. my asa work like site to site vpn with the other asa5505. i would be love that monitoring status of VPN. i enabled on asa logging, i puted address of smtp server, receipent email, source email, the problem is because my smtp server require authentication, TLS. how set configuration on asa5505?
configuration of logging for send notification on email.
why the following configuration is not working? I have two clustered ASAs inline from one another, in front of a 4506-E switch in front of a host I want to access via RDP, like so: My issue at this stage lies with getting the UNTRUST firewall configured. I've tried the following configuration 1) Creating the host.
View 13 Replies View RelatedI'm trying to setup an IPSEC tunnel above GRE using the topology in the attached image file.However the traffic between the 2 endpoints: lo0 on R5 (10.0.5.1) and lo0 on R4 is traveling via the GRE tunnel without being encapsulated in IPSEC: I'm using 2 routing protocols:
- OSPF area 0 for the connectivity between R1,R2 and R3
- EIGRP AS 1 for the internal sites connectivity
I'm shortly going to move our stuff to a new data centre, where we have two network feeds - so there'll be two lengths of CAT 5 coming into the rack, for "first hop redundancy".I have something similar at our existing DC, but I'm simplifying the equation somewhat at the new DC, and using a simpler configuration that just uses two switches, rather than two switches and two routers. All of the servers will have public IP addresses.Now - the network guy at the new DC has confirmed that a simpler two switch configuration will work.
View 17 Replies View RelatedCisco 3550 and when I do a sh int fa0/1 and the status does not show last input or last output. Is a 3550 have a configuration that needs to be set?
View 0 Replies View RelatedI have a nat configuration to apply on a 8.4. I am a bit confused.On a ASA 7.0 the configuration is as such static (inside, outside) 10.102.247.0 10.102.247.0 netmask 255.255.255.0Basically, I want a bidirectional nat .. for users to connect to the inside network using the real IP.object network Delta subnet 10.102.247.0 255.255.255.0,object network Delta
View 0 Replies View RelatedThe basic setup Newly installed redundant ISP, thus setting up the 891 with dual WAN Using PFR to load balance between the two. Did initial config through CCP (not express), but I am familiar with the basics of IOS CLI (not used to the new zone based firewall yet, managed aour old Pix for too long, but that is a different subject)
I cannot seem to get anything but Gi0 to be accepted as a WAN interface. I go through the entire setup in CCP, test each connection, etc, and it all looks good until I exit out of CCP and go back in. At that point, I get squat out of Fa8. CCP won't let me test the connection, won't let me edit the connection, wont let me delete the connection. The wizard for a new WAN connection becomes available again (Wanting to set up a "second" WAN on Fa7...)
Again, I have verified connections to each ISP line independently, either one works just fine on Gi0, neither ever works on Fa8. This is my first real foray into PfR.
Building configuration...
Current configuration : 21486 bytes
Last configuration change at 18:59:43 UTC Mon Mar 26 2012 by admin
[URL]....
After launching config collection job in LMS 4.2 I can't get job results and receive error message - Unable to get results of job execution for device. I've increased the job result wait time using option in Admin > Collection Settings ... , but nothing changed.Here are screenshots of error message and wait settings I used.
View 3 Replies View Related