I have two nic one connected with DSL modem with gateway 192.168.1.1 for Internet. another nic connected with office Intranet with gateway 10.226.122.x . I can connect only one network at a time disabling other.. I know route add command can be used for linking the both network so I can simultaneously use Internet and Intranet..can you elaborate with example (five years ago I set up the same with route add command.. now my memory failing..)
I want to know with an ASA 5505 w/ Security Plus License I get up to 20 VLANS/Named Interfaces.I have a customer that is getting a new subnet of external IP addresses from their service provider and a different default gateway to accomodate re-hosting their datacenter at their main office instead of at a Colo. My question, when building out their new DMZ, can I have multiple route 0.0.0.0 commands?
Example.
Current Default Gateway 1.1.1.X
Internal hosts 192.168.1.0 use and are natted to 1.1.1.X
New Default Gateway for DMZ Servers 2.2.2.x
Internal hosts still use 1.1.1.X, but server hosts in 192.168.1.3 should use 2.2.2.X -- there are also a bunch of pre-existing static NAT rules for these servers such as 2.2.2.30 translates to 192.168.1.30.
I think I would accomplish this by using the following:
There are no commands like route-map & ip sla monitor on my cisco 1841 router, its ios version is 12.4(T1). I have to configure load balancing and failover on this router but without these commands i cant do that.
I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
I am having issues recieving UDP response from my smart lighting control, i can here it in the same town but not from overseas..internal ip address 192.168.0.3 port 6000 it hears my commands from overseas i just cant here its response.
In studying and testing SSL VPN on an ASA I have the network as shown in the attached diagram. The configuration is based on an ASA with 8.3 but our ASA is 8.2 and at this time I'm not familiar with the new NAT configuration and commands in 8.3 or later and how to translate the 'nat (inside,outside) source static' for me to an 8.2 version.
I try to get a ASA with the new software 8.4.2 running. On an old pix we had the nat command: static (inside,outside) tcp interface www 192.168.15.252 www netmask 255.255.255.255 0 0,In all the new documents about 8.4.2 I can find that it should work with something like:
I want to forward http traffic from the outside interface to this host. In the log I just get entries about blocking ACL - but both is allowed on the outside access-list - traffic to the inside IP and also to the outside interface IP.
I also tried it with "Public Server" - but when I try to use the Interface address I just get the message: Address x.x.x.x overlaps with outside interface address.
Is it still possible to do port forwarding on the outside interface?
I have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
I have configured the TACACS in my network and I have configured the aaa authorization commands 15 default if-authenticated group tacacs+ in Cisco 6504 Switch. Its allowing me to Login by Unable to run the Sh run commands ,i am getting Aithorization error emssage. If i am checking sh Privillage its showing level 15. Same configuration fine in other device with out issue.
Are the IOS commands the same on a router and a ASA for these two topics....CBT Nuggets where I train has 553 videos for some of the new topics. I am preparing for 554 as it has more ASA focus and thats more interesting to me.
Have a conceptual question bout CLI command authorization. We have ASC 5.2 up and running, providing AAA services for network devices. Now I need to make profiles for users in certain group to restrict dem CLI "rights" to show, clear counters and show running-config commands. I need to accomplish dis task.I should clrete separate privillege levele profile (let it be 2), specify commands at this level, assign Group this Authorization Prifile and make some additional changes in my devices.
I am looking to configure PBR in Nexus. The current setup in IOS is :
interface Vlan10 ip address 172.27.206.1 255.255.255.0 ip address 172.27.208.1 255.255.254.0 secondary ip policy route-map Vlan_10_to_Corp route-map Vlan_10_to_Corp permit 10match ip address Vlan_10_to_Corp set ip next-hop 172.27.209.250!route-map Vlan_305_to_EFH permit 30
[code]....
But, Nexus PBR will not work with deny statements init. Now, what options do I have ?
we've got a pair of old 3745's that are getting upgraded to new 2911's, and I'm trying to run IOS 15.2 on the new routers to get them most current before going into test and production use.The routers are doing BGP, IPv4, and HSRP, and I'm trying to put one in at a time as to not have to big bang everything at once. I'm putting the one that matters least in first, and basically using the same config as the old one, which was running IOS 11.
I was using "no ip mroute-cache" on ethernet interfaces, and it says that command is deprecated and I should use the MFIB commands instead. Darn if I know what that means, I believe it was set up so the ethernet interfaces had IP multicast fast switching disabled, which was set up by our vendor 10 years ago so I'm not sure if it matters. It would seem logical to me this would have an impact on HSRP and speed of failover. Does this matter, and if so how in the world do I do this with IOS 15.2?The second one is the use of "no fair-queue" on our serial connection for a T1. This command isn't there either, and I'm not sure if I even need to bother on this. It was set up on the old router on a T1 Frame Relay circuit.
I have just received 4 static ip's from my isp, i want to be able to point these ip's at different services on my internal servers, for example: [code]. The firewall I have is Cisco PIX 515, how to set the NATing up or commands?
today I received a Cisco Router 881G with PCEX-3G-HSPA-G for a customer that ordered a Router with the feature to send/receive SMS and to remotely active the 3G Internet connection through SMS. I believe that the router that meets this requirement is the Router 881G that I received today. In particular, the model is:
CISCO881G-K9
Now, I installed the router and configured the 3G link that is working properly BUT all the commands related to the SMS are completely missing. In particular, I miss the command:
cellular gsm sms send gsm sms archive path
In the following documentation I see that these commands should be available: [URL]The fact that these commands are missing sounds very strange to me since the documentation is pretty clear. Do I need to activate any license? I also upgraded tha router to the last version...
Here it is the show version of the Router:
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1) Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc. Compiled Sat 24-Mar-12 00:00 by prod_rel_team ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
I have created a baseline template to run compliancy checks, I understand that lines beginning with a + are mandatory and lines begining with a - should not be on the router. What I need to know is, is there a catch all for any other commands on the router config (startup or running) but not mentioned in the baseline? For example, lets say this is my baseline:
+ service timestamps debug datetime msec + service timestamps log datetime msec + service password-encryption + hostname [hostname]
The router comes back as compliant as it has all the above lines. However there is obviously more config on the router, but this doesn't show? So I know I can get commands that are in the baseline but not on the router; but what about the other way round - on the router but not on the baseline? Surely this exists - at the least from a security point of view, an attacker could well have configured the Dot11Radio int, however without entering the command with the minus prefix I can't tell? LMS 2.6
I'm using a cable connection with my router and most of the time I'm playing FIFA12 on PS3 i feel like the commands takes a second to respond, like if was a delay. I tried most of everything in firewall settings, port foward, internet settings...
We are replacing two 3750E switches with 4500X using cat4500e-universalk9.SPA.03.03.02.SG.15111.GS2
1. is there a command reference available for this ios - can't seem to find out 2. Im using GLC-T gbics and we normally would set the speed to either 100 or 1000 now that option does not seem to be available. 3. when I entered username etc. I got a message " CLI deprecated soon".
To test the VPN performance of ASA 5540, I will have to build at least 1000 VPN tunnels. It is time-consuming works if I put all of commands line by line manually. It looked like a bundle of VPN tunnels won't be created by ASDM. I am wonder if there is any generator tool for this. I just tried to google it. I found a software is named as VPN Configure Generator, but it is not free.
I have cisco 2911 with IOS-universalK9 mz.SPA.150.1.T, but that does not accept the ip sla monitor commands XX, XX or rtr ip sla XX. How active these commands in IOS or what you belong to?
I do not have the option to run sh mls qos commands. I am trying to look at the cos-map on my 7200 router. The code I am running is c7200-p-mz.122- 25.s9.bin.I also do not see the mls qos command listed globally and it is not an available command in config t mode.
SSH commands not available in IOS cat4500e-universalk9.SPA.03.02.00.XO.150-2.XO.bin I just recently upgraded to universal k9 as the k9 versions usually include the crypto, shh commands however I still do not have access to these commands, is there anything I must to to enable these?
I am trying to set up a SLA statement on an ASA 5505 version 8.2(5). When I enter the command "sla monitor schedule 1 life forever start-time now" I get a message stating "%Entry not configured."
I have configured below SNMP v3 commands in Cisco Router 7206VXR (NPE-G1) . I have tested with all option but it is not working . SNMP server is a SNMPc tool and I have configured user name and piv and authentication credential correctly in both side . Same configurations is working for all Cisco switches but not working for Cisco Router.
SNMP V3 configurations:
access-list 20 permit 43.194.10.0 0.0.0.255 snmp-server view readview iso included snmp-server group readonly-group v3 priv read readview access 20 [ code]....
Router :
Host Name# sh versionCisco IOS Software, 7200 Software (C7200-ADVIPSERVICESK9-M), Version 12.2(33)SRD7, RELEASE SOFTWARE (fc1)[ code]...
I have just received a new cisco 2901 and started on its configuration. when I started configuring VPN tunnels, I saw that non of the crypto commands are available.
The router runs on iOS 15.1.From what I read, people refer that the router needs to past a license activation or something like that. When I run show verison - i do see "none" under most of the categories.
Why do my cli commands just scroll all the content rather than having to press space to show more? It is hard to type sh run and the entire config flays past rather than being to inspect it page by page.
I want to setup a voip network, there's going to be 3 switches connected to a Cisco CME router, my problem is I can't find information on how to configure it.
I am looking for soem best-practice and useful logging commands on 6500 and 3750 platforms. Some of them I have listed below. Is there any important ones I am missing Also, I need to know what kind of recommended logging level is for buffer and what is loggign level for syslog server?
