When WAN traffic meter is enable on RV180 router maximum throughput drops to 40Mbps from ~120Mbps.Enabling WAN traffic meter is needed to get SNMP data from WAN port.
View 1 RepliesI configured my RV120W (Firmware:1.0.2.6) to count the traffic on my network. I set the monthly limit to 99999 and did not change anything else.So after a few hours, the traffic counter shows 2048 MB for outgoing traffic. This is impossible, because the DSL-connection is too limited in upload to cause this huge outgoing traffic in 6-8 hours. When I reset the counter at night, the next morning the device shows 2048MB again (even if there was no traffic at all, just some clients syncing time with NTP). I did already reset the device to factory defaults and reconfigured everything from scratch.
View 0 Replies View RelatedI have rv180w (firmware 1.0.1.9) and 1 Gbit/s internet.When i turn on WAN Traffic meter, WAN speed down to 100mbit/s.I didn't find any suggestions in official documentation.Is this a bug or undocumented feature?
View 2 Replies View Relatedwhat the maximum Data Througput can be for this router. Right now, the router is limiting my internet speed compared to what the cable modem can provide..So far, I know that when I connect my computer directly to the output of the Motorola Cable Modem and run a Speed Test on my Charter cable connection, the test shows ~ 50 Mbps for downloads and ~5 Mbps for uploads. That would be great, but I have multiple computers and need to use a router/gateway to feed my LAN. When I insert the RVS4000 router between modem and computer, the Speed Test results drop to ~ 16 Mbps for downloads and remain ~ 5 Mbps for uploads. During that test, there were no other computers online via the router. While 16 Mbps is not shabby, I would like to achieve the full value... is that possible?
Is the RVS4000 unit capable of 50 Mbps for 30 Mbps? How do I setup the router to achieve the maximum available download speed?There is a setup page for the router which has settings right now set at 50000 Kbps Upload and 60000 Kbps for Download; this implies to me that the router is capable of such speeds.
as we know twisted pair cat 5 has maximum length 100 meter?
is because the voltage will decrease"weak" at the receiver "because the resistance of cable"? or because the noise will increase?
I am working w/ WNDR3700, and I've been trying to take a look at the traffic meter to judge how much I actually us.
In 7 days I supposedly already used 30gig. There are only two computers to the network and the most we do is Pandora/gaming. Is this router incorrectly reading incoming/outgoing data? Is there someone logging into my router and downloading freaking porn or something? Because whenever I check to see connected devices, I only see our comps, are they able to hide their device on the router?
This month
153:58 Upload/Avg=2,562/366.03 Download/Avg=30,228/4,318 Total/Avg=32,790/4,684
The most I do on the web is schoolwork/pandora and play league of legends or counter strike.
I need to provide a router to connect Internet circuit and run IPsec to MPLS network. Circuit is 10Mbps.
What is the max a Cisco 881 can handle if running IPsec?Also, if you are aware of any branch router (1941) which allows connection to future 4G LTE .
We are looking at providing an ISR 819 for one of our customers using FTTC & 3G for failover .. However, I cant seem to find any recommended throughput guidence for the device? We could be looking at up to 80Mbps via the ethernet interface and I just dont know if the device will cope?
View 4 Replies View RelatedAm looking at purchasing a router that is capable of serving a WAN bearer at up to 1Gbps. The 3945E has had good reviews as a high throughput router but the datasheets suggests performance of 350Mbps. It also states that additional performance can be ensured by adding SPE modules. Whether the 3945E could achieve up to 1Gbps with SPE modules?
If the 3945E can't achieve such performance, The key features I am after are:
IPV4 and IPV6 support
L2tpV3 support
BGP
IP SLA
1Gb Copper Connections on-board with capability of at least 4 Ports
I have a asa5580 with multiple interfaces. To replicate me databases to another site, I mainly use two interfaces on that firewall. Those interfaces have a steady pace, around 95%.
I am wondering when I should consider that the thoughput between those two interfaces is too much? Is there a good document that could explain me clearly why?
Also I want to be sure that I won't affect the normal traffic between the other interfaces. Is there a way to garantee certain traffic over others on an ASA? I don't have any router in me setup layer 3 role is perform by asa firewalls (static routes).
I cannot find this info on the cisco site.
View 2 Replies View RelatedDoes anybody know the Maximum Throuput of a Csico 4948 using its Layer 3 capability? Is it 72mpps for Cisco 4948 and 102 mpps for Cisco 4948 10 Gigabitethernet?
View 2 Replies View RelatedWe are experiencing output drops on our 3750G-12S (IOS 12.2.55).
I have monitored throughput with MRTG, but it doesn't seem that high compared to that the 3750G is supposed to handle 17.8 Mpps.
The 3750G's are stacked, running ospf, qos, multicast (IPTV) and etherchannel.Is the maximum throughput reduced by stacking or any of the other features?
I don't know if one can estimate what the maximum throughput is per ASIC or per port, but on one of the ASICs that is having drops the peak unicast load is 1.3 Mpps and multicast Mpps is 0.9 Mpps. Total ~2.2 Mpps.
This doesn't seem high at all and I don't understand why the drops are appearing. What I can do to find out the reason for these drops?
We have 15 small branches with Cisco 881w in every office, they use VPN site-to-site to vpn- concentrator on V yatta. I launched cacti monitoring of cisco 881's CPU's Errors, Traffics, Non-uni cast, Uni cast. I see that on 10.00 pm in one brunch when nobody works there, CPU load reaches 50% and traffic rises up to 9mbs.
View 10 Replies View RelatedIs there any way to manage the RV180 from the WAN side via https and/or ssh?Also, is ssh from LAN even available?
View 3 Replies View RelatedI have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.
View 6 Replies View RelatedI noticed if you add more than 10 access rules to the Access Rule table, you are unable to reorder past the first 10.Steps to reproduce:Create 11 rules of the same stream direction, outbound or inbound (...I found the bug with outbound, did not test inbound).try to reorder one of the first 10 rules to the end of the list, either by entering "11" manually, or by pressing the down arrow.System responds that "11" is an invalid number, or that the rule cannot be moved.This issue is not reported in the "Known Issues" section of the release notes for 1.0.1.9.
View 2 Replies View RelatedWhich vpn client to use on os x ? (the one included in os x or another?) Which VPN configuration to use on RV180 ? and Which ports to open on RV180 Firewall ? (or any other parameters)
View 1 Replies View RelatedI had set up QOS for an IP Range and noticed the logs filling up with Warnings - hundreds within less than an hour.
I finally reset the router to factory and then step by step re-built my configuration - it was the QOS that started generating these warnings like:
Tue May 21 13:18:39 2013(GMT-0500) [rv180][Kernel][KERNEL] [87073.550000] IN=bdg1 OUT= DST MAC=d8:67:d9:c3:a0:2e SRC MAC=00:0e:58:58:57:7a PAYLOAD TYPE=08:00 SRC=192.168.1.193 DST=208.85.44.22 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=19313 DF PROTO=TCP SPT=1768 DPT=80 WINDOW=2534 RES=0x00 ACK URGP=0 MAR
[Code].....
In both cases above, after I started to suspect QOS, I entered a narrow IP range to test and then a MAC to test. Using a VLAN seems to work fine and generate no errors - even a VLAN for the same associated host(s).
I have a support case open about this - didn't get too far yet, but now with a better repro, maybe they will.
i have gotten a question from a partner in regards to the throughput on both LAN and WAN on the SRP541W. I can't really find that on the datasheet.
View 4 Replies View RelatedI currently have an RV180 in a small business set-up and curently being accessed remotely by laptops (Quick VPN) and Ipads/Android ICS tablets (PPTP). All is working well but I've become concerned about the security risks of PPTP and would like to shift the tablets to IPSec.
1) For a small business are the PPTP risks real?
2) What are the alternatives for Android ICS? I can't find a Quick VPN client for Android.
3) I can't get the core IPSec VPN in Android to connect to the RV180? Is this possible?
I have RV180 configured with two VLANs. First VLAN is untagged and second VLAN is tagged. The purpose is two have two subnets, with the second subnet used for guest access. Both VLANs have DHCP server enabled. First VLAN is 192.168.1.0/24 and the second VLAN is 192.168.2.0/24, When I connect a computer with untagged Ethernet interface, it gets an IP address from DHCP server on the first subnet i.e. 192.168.1.100 and it can successfully access Internet. When I connect a computer with tagged Ethernet interface (I am using VLAN ID 10), it gets an IP address from DHCP server on the second VLAN i.e. 192.168.2.100. So far so good. I can successfully ping hosts on the Internet i.e. ping www.google.com. But I cannot access Internet from the web browser. I captured Wireshark trace and here is what I see...
1. TCP SYN. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
2. TCP SYN ACK. Source IP A.B.C.D, destination IP 192.168.2.100. Ethernet frame has VLAN tag (VLAN ID 10)
3. TCP ACK. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
4. TCP Data. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
5. TCP Data. Source IP A.B.C.D, destination IP 192.168.2.100. Frame is untagged
The problem is at #5. Packet came back from the Web Server. RV180 properly NATed it to the local IP address. But it did not add VLAN tag.
I just recieved a new RV180 yesterday and it will not connect to my switch. Router was updated to the newest firmware, reset to factory settings. I did change the ip and ip range. Router works fine with one computer attached direct. As soon as I connect my sf300-24P to it, the WAN and LAN lights all light up and then go out. Only the WAN will light back up. I have no connectivity to the router. I plug the laptop to the router directly and no LAN lights come on and can not see the router with arp -a.
View 6 Replies View RelatedI'm trying to telnet into the my RV180 router. How do I go about it.
I created 3 VLANS
1 at 192.168.1.1
20 at 192.168.20.1
30 at 192.168.30.1
Here is the Multiple VLAN Subnet Table:
1 192.168.1.1 255.255.255.0DHCP ServerEnabled 10192.168.10.1255.255.255.0DHCP Server Enabled 20 192.168.20.1 255.255.255.0 DHCP ServerEnabled
I can ping the router at all 3 IP addresses.How do I enable the telnet service on the router?
Does RV180 router support client VPN connections using regular Cisco VPN client? Datasheet says it works with Quick VPN client.
If regular non-Quick client is not supported, can both clients coexist (= be installed simultaneously) on the same PC?
Does Quick VPN client support split tunneling?
I'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.
View 1 Replies View RelatedI'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.
View 5 Replies View RelatedIs there a guide to setup a VPN connection using this router? I've follow the setup guide provided by cisco but I'm having issues. When attempting to connect using the quick vpn client, I get error messages.
View 1 Replies View RelatedAny news on a new firmware for the RV180? I have the most recent version but it still has lots of bugs. IPSec needs polishing. In addition the Logging functions don't work well. I can't send to a syslog and when I try to email the logs I get a email saying there is no data even though several pages of enteries are visible in the web GUI. I've checked the profiles and they are correct. I even tried using just the 'default' profile but no luck.
View 2 Replies View RelatedI have a Cisco Small Business RV180 and I have several VPN users configured. IPsec between my home router (also an RV180) and work router (router in question) is working fine, several PPTP users working fine and 1 QVPN user that works as well. I set up another qvpn user and it didn't work. I went back into the router to check and make sure I hadn't goofed something up and saw that I had 8 lines, 1 and 2 were the QVPN users and 6 other PPTP users, however, the "pages" footer (for lack of a better word) only displays 1 -5 of 5 instead of the 1-8 of 8 I would expect it to show.I dumped the cfg file and opened it up, all 8 user configurations show up. One was my user account which showed negative numbers for the logon time, something like -1day -hours -minutes -sec, so I thought that that might be locking up the router or something so I deleted my PPTP account but it didn't allow the new user access. I deleted all PPTP accounts and no luck there either.I'm running firmware 1.0.2.6.
View 4 Replies View RelatedI am contemplating replacing my Juniper Netscreen 5GT with this new RV180.
serial number 161303LB
RVC180 V01
However, it will not connect to my ISP (DSLExtreme) using the same settings I have been using for multiple years. DSLExtreme is using AT&T DSLAMS, as you likely know, and I am unaware of anything unique about how they serve DHCP?
The Cisco wizard sits on the WAN configuration check forever, and never connects. I have rebooted it and allowed it to sit for fifteen minutes trying. I think that is enough.
The 5GT WAN interface is configured for "DCHP Client" and that is how the RV180 is configured.
It is a standard 6MB DSL line, I have tried both the existing cable, as well as the provided one to connect to the D-Link 2320B modem/bridge, which, as I indicated, syncs almost instantly with the Netscreen. No difference when the cables are swapped.
My brand new RV180 seems not to be able to exceed 1.1 MB/s WAN download speed. Using a simple Linksys WRT-320N I used to have 5-6 times this speed. Value is with default settings, various sources (HTTP/NEWS downloads). Trying to improve this wit QoS-settings dows not improve this in any way.
View 2 Replies View RelatedThe RV180W would not connect to an AT&T DSL connection using PPPoE (modem in bridge mode), or behind the DSL Modem/router with the DSL modem/router providing a dynamic IP to the RV180W or a cable modem (TimeWarner Roadrunner dynamic IP). I upgraded the firmware yesterday and now the RV180W will connect to a dynamic WAN IP, but it still will not connect using PPPoE.
I have also noticed the admin interface is only accessible about 75% of the time. When going to 192.168.1.1 the login prompts either don't come up or if they do, after logging in, the screen never fully loads after that. I have to reboot the router to get it to work.
Also, the router has not yet pulled DNS from either the DSL or the cable modem. I had to manually enter those addresses.