For some time now I've used the USB port on RSP440's fitted into ASR9006's to load IOS with no problems.Recently I noticed that the ASR9001 USB port doesn't seem to work at all, which seems odd to me as I believe the 9001 uses the same card built into the chassis.All routers were running the same code version 4.3.0, and I was using the same memory stick?
View 1 RepliesWe have ASR 1006 with IOS XE and i want to see the Software License but somehow i cant!!! ...i googled it but i could not find anything.how can i see the available license on ASR 1006 or 9000 series?
View 1 Replies View RelatedI have a philips tv 9000, qnap 210, twonky and e2000. When i using my e2000( wireless/cable) the tv stops playing the vids after 5 min.When i using un very old smc router there's no problem.
View 6 Replies View RelatedI am trying to access a device behind my firewall that needs to use port 9000. I have completed the single port forwarding page with the exterior and internal port but I cannot access the device from outside the firewall. Yes I did check the "enabled" box
View 8 Replies View RelatedHave a E4200 with version 1.0.04 firmware.Been trying to open 9000 to access my buffalo media server remotely. Have set up both Single Port and Port Range Forwarding for port 9000.On trying to access media server, get message " could not connect to xxx.xxx.x.xxx:9000"Using online Open Ports Checkers shows this port is closed.
- Tried disabling all firewalls.
- tried range of ports
- Enabled/Disabled UPnP
- tried cisco & buffalo tech support
I have a RV042 using (for now), just the single WAN interface. I am trying to forward all packets to port 9000 from the WAN to a single IP address on the network. I've set up both forwarding rules under Setup -> Forwarding and under the Firewall -> Access Rules.I cannot connect to my device from the outside world, however. Is there something I'm missing?
View 4 Replies View RelatedI need to open ports 9080 and 5280 on my Cisco ASA 5505 firewall and despite doing everything I THINK I needed to do...when I run the utility to check from outside; it is NOT open....I utilize a website called [URL] (very good for these kinds of things) I have added the specific port(s) to my services so that I can CHOOSE them; added an ACE/ACL to; added incoming/outgoing rules to accomodate traffic to those ports....NOTHING.
View 7 Replies View RelatedI'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies View RelatedHow do I disable the USB port in the 881 router?
881router#show usb port
Port Number: 0
Status: Disabled
Connection State: Disconnected
Speed: Full
Power State: ON
I've tried a few different ways unsuccessfully so thought I'd ask here.I'm trying to forward an outgoing port on a Cisco 800 series router. ie. When a user inside the network connects to the router on port 1234, it opens up the same port on a server on the Internet.
View 2 Replies View Relatedwhich 800 series routers allow 20 Mbps throughput across the WAN port? I have a cable modem that outputs this speed but am having difficulty finding a router that will accept this throughput across the WAN port.
View 21 Replies View RelatedI have a Cisco 800 series ?I need to allow access to our local server from a specific range of external ip addresses.I can open port for all external ip using this command:
ip nat inside source static tcp <localserverip> <port> interface <interface> <port
But this is not secure as is..Do I then restrict and permit access using access-list? Or is there another way altogether?
Cisco Catalyst 2960 series,i want do a SNMP request over OID. When the output should be like this: Portnumber and VlanID. Is there a OID for this output?
View 1 Replies View RelatedI just setup my homelab today, after having Cat5e installed so I can run my servers and network equiptment over wired network as well as setting up a wireless system. I got everything setup and its going great I can access everything from my office now including a E4200 Linksys router that I setup to do RiP (was only choice pretty much, or NAT), and my 891 Cisco Router which is my internet connection.
I use to have the linksys setup to do port forwarding but now I need to figure out how to do it on the cisco 891 router via command line.
Below is my current configuration. I need to be able to access my server which is behind my router by Remote Desktop. I also have a web server, and the kids also play minecraft, and have a server setup so I need to be able to forward their port as well.
[URL]
Ths is from the link above, would I just do like that but then put in my IPs and is that my Private IP I use this or my public facing. Also he has "interface Dialer1 6881" again after the port in the second and third row. I dont really understand what they have there. I understand basic access list and such though I am extremely rusty.
!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.0.0.2 6881 interface Dialer1 6881
[Code].....
I found the following on the link bundling page for the 12000 series router:"In both EtherChannel and POS channel link bundles, the Link Aggregation Control Protocol (LACP) for signalling and the 802.3ad protocol for automatic negotiation of the channel are not supported. This means that in order for the channel between two routers to be active, you must disable signaling on switches (such as the Cisco 6500/7600 Series) in the channel, and configure the switches in ON mode."
So, my question is, if lacp isn't supported, is there another way to mimic its functionality on a 12000 series router? I want to connect 2 routers together with a port channel that will pass through our layer 2 network, and I want to make sure that any failures in the path will shut down the affected link on both routers.
I'm using a SRP521W-U. I've set up a SIP account on Line 1. I would like to be able to answer incoming calls on both FXS1 and FXS2. How do I achieve that both ports will ring?
View 2 Replies View RelatedI'm having a problem getting DHCP working with an ASR9k as shown in this document. I've successfully implemented very similar setups with some Cisco IOS routers, but the IOS XR on the ASR seems to be defeating me. Router A (happens to be a 3750)A DHCP/BOOTP/TFTP server, connected to router ARouter B - this is the ASR, running software version 4.0.3.Router A and B are connected by a layer-3 link.Router C (happens to be a Broadcom embedded router). It's connected to Router B by a VLAN trunk link.Device 1, this one needs to get its configuration by DHCP/BOOTP/TFTP. It's connected to Router C by a VLAN trunk link.Device 2, this one doesn't need any DHCP/BOOTP/TFTP. It's connected to Router C by a VLAN trunk link (its port is the same as Device 1's) Device 2 works great - it can ping the DHCP/BOOTP/TFTP server (and vice versa) and everything else it needs.
View 0 Replies View RelatedAccording to the url below, i could find that there is a separate module required for asr 9k, is it so; doesnt it sufficient to have the 4.3.0 Ios-xr version for the cgnat supoort features of nat 44, nat64, ds-lite.. like things?URL
View 1 Replies View Relatedwe have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
I don't see it in the menu as it was in the classic firmware. does that mean i cannot forward specific port to open a port in Transmission on a mac?
this is the only thing i see - but what i entered does not work - port is still closed.
i've a bit more complicated setup:
main house - comcast modem and wifi router <--------> guest house - WIFI bridge - ethernet cable to a WIFI router - my apple laptop. WIFI bridge is ASUS with DD-WRT firmware. i get good speed up to 20mbps/4mbps (down/up)
transmission works, but the port is closed ? doe it really matter ? what can i do to open the port (for e. "61622") ?
I have a e4200 router, And a 660 series modem, I'm trying to portforward for a game called minecraft, I cannot seem to get the ports to open, I've called Century link they told me to put my modem in to bridge mode, So I did they said my IP should be public not private now, It is still private
View 6 Replies View Relatedsimbageo[at]sbcglobal.net I had a razr cell phone and it connected to ford sync in my 2012 escape correctly. I tried to connect my motorola cdm-9000 to ford sync and it tells me the phone is not found... I realize the Motorola is an old cell phone.. Doe's it even have a blue tooth capability? My understanding that the cell phone has to have bluetooth capability to connect to for sync.. Is that correct?
View 2 Replies View RelatedI am trying to find a solution using modular QOS when there is congestion in circuit we drop packets with WRED which are marked with a DSCP value of say AF21. I can drop those traffic completely in case of congestion. I was thinking to allocate 100% bandiwth to rest of the traffic.
View 1 Replies View RelatedI want to configure IEEE 802.1x port-based authentication on cisco switches, preferable 2960 series. Which models support this feature?. I have try with some older switches but it doesn't works properly on everyone. I have upgraded them whitout better results, there is namely an issue with TLS handshaking on some switches which produces authentication to fail.
View 1 Replies View RelatedI want install a wireless card--dual band, N, -- in my Studio XPS 9000 desktop. I have a dual band router.My questions:
1. Are the expansion slots PCI or PCI Express?
2. What card is recommended?
I have many alarms with CWLMS 4.0. The alarms are OutOf Range Voltage, OutOfRange Temperature and OutOfRange Memory. I don´t know how eliminate this alarms for these equipaments. I am trying with Setting up the thresholds but nothing.
View 3 Replies View RelatedI have 3 WAP200e APs in a client site and I am having a problem with the signal between the APs and Motorola 9000 barcode scanners.The first one went in about 6 months ago and it worked fine. The client then asked for two more to be installed in a couple of rooms adjacent to the room where the first AP was installed. They use barcode scanners with these APs and since the two new ones were installed, the first on is dropping the connection to the scanner. I have turned the new APs off and everything is back to normal. I have reduced the power output of the two new APs and the situation has improved, but they still get problems, especially on Monday morning, where it won't work at all for the first few hours, and then bursts into life and works fine for the rest of the week.
View 7 Replies View RelatedI am in a small office and we have a Buffalo NAS being used. Configuring it was fairly easy, but recently it just stop letting us have web access. My External and Internal Ports were 9000, but for some reason now my router will not even show that there is a 9000 port and even if I port forward it. It does no good what good possibly be keeping this port invisible after it was being used the last couple of months. I called my cable company and they said they are not blocking it. But right now I cant access the server from a remote location.
View 4 Replies View RelatedI'm looking to setup a few ip security cameras in my house and would like to monitor from work. The first thing I did was give the ip camera a static ip on my local LAN 192.168.1.104. I also forwarded port 9000 to this ip. I then went to [URL] to look up my external ip address. I was able to obtain one ip for my router and another for my modem (disconnected router and went direct through modem).
I've since tried to ping my router WAN ip from work numerous times via http://24.x.xxx.xx:9000 and I get timeout errors. I've tried traceroute and it gets close, but times out the last 3 hops. I've had Comcast on the phone many times trying to resolve and needless to say they weren't able to work.
I have a switch that I have configured for jumbo packets, but they don't seem to be functioning. I have set system mtu jumbo 9000. The hosts are connected via 2x EtherChannel links. The hosts are jumbo frame enabled, and can ping their own local address using jumbo packets & do-not-fragment flags on the pings. They cannot, however, ping each other or the switch that way - it always says that the packet requires fragmentation. I know the attached machines (they're all VMs) and virtual switches support jumbos because I can ping within the virtual interfaces of the VMs. It's just traffic that goes over the switch that fragments.The switch is a WS-2960G-48TC. Here are the various outputs, with a section of config at the end.
hrnacancwtdevs3#show system mtu
System MTU size is 1500 bytes
System Jumbo MTU size is 9000 bytes
System Alternate MTU size is 1500 bytes
Routing MTU size is 1500 bytes
[code]....
i've a cisco asa5505 on adam 6.4 and a dvr i would like to forward the ports 9000 and 85 in order to monitor the dvr from outside?
View 1 Replies View RelatedCan we force the Gigabit Ethernet port to be 1000 full duplex in Cisco Catalyst Express 500 series?
View 3 Replies View RelatedWe have a number of sites which have high-speed L2 links which terminate on our L3 switches at each site. The ports are between the sites are placed in routed mode.
I would like to use Jumbo frame between two of the network which will communicate across sites and 1500 mtu on the rest, is this something which is possible?
From my understanding is the mtu is set on the interface therefore if I set the mtu on the L2 link ports on both sites to 9000 then would this cause a problem for the 1500?