I have a 128mb connection with a sa 500 series fw/router. When I turn on the ips function my throughput drops to 15 Mbps and the CPU max goes up to 100%. What gives?
View 2 Replies300 M bps drops to 150 M bps when it recycle power. I met all requirements for 300 M bps connection this happen only in 2.4 g Hz Band width.
View 1 Replies View RelatedI have a Netgear CG3100 modem hooked up to a Netgear WNR2000 router. Both are sending out signals, the CG3100 on channel 11 at 40 Mhz and the WNR2000 on channel 1 at 20/40 Mhz. I keep the WNR for legacy devices while the CG is for N devices only. They don't seem to interfere with each other much.Currently my computer is the only device connected to the modem wirelessly, with the only wired connection being the router. As I write this, the connection has actually dropped to 26 Mbps in the Wireless Network Connection Status window. I understand that this number drops under network load, but there doesn't seem to be any at the moment. If I go into the control panel and simply click apply, the connection jumps back up to 150 Mbps. However, this always drops back down, sometimes immediately, sometimes after a few minutes. It usually settles down at 72 Mbps, sometimes 54 Mbps.My wireless adapter is an ASUS PCE-N13 with v3.2.7.0 Ralink drivers. OS is Windows 7 64-bit.
View 6 Replies View Relatedwhich 800 series routers allow 20 Mbps throughput across the WAN port? I have a cable modem that outputs this speed but am having difficulty finding a router that will accept this throughput across the WAN port.
View 21 Replies View RelatedI have a Rosewill RNX N300X wireless adapter that keeps dropping to 1 mbps, and only goes up to about 18 mbps on a good day. How can I force a 54 mbps connection?
- I am running the latest drivers for the card.
- The network is "g", card accepts b/g/n.
- Another computer running RNX N360PC is getting a perfect connection on the same network.
I purchased a new router - cisco e1000. Currently, i have 2 laptops wirelessly connected to this router. When i do a broadband speed test, the speed drops down significantly to 8MBPS while if i connect it to the cable modem directly (wired) i.e., without router, i'm getting 15 MBPS download speed. I did a couple of times this speed check and the results are same. I tried changing the advanced settings in the router (which was specified in one of the post in this forum) but no luck. Is it that i need to buy e4200 to match the wired speed of 15 MBPS or what other things I can do to get the same speed of my cable modem (provided by my ISP)?
View 1 Replies View RelatedI'm running a Cisco E4200V2 router with the latest firmware (2.1.4.12284) on an iMac running OS X 10.8. My ISP is providing 15Mbps to my modem, which I've confirmed by connecting directly to it without the router. Once I put the router back in the path, my broadband speed drops to about 6 Mbps. Is this the best I can expect from this router?
View 2 Replies View RelatedMy RV110W is only a few months old and apparently started ginvg me issues shortly after I got it. Since it was new, however, I only recently suspected it as the culprit!
I have a simple home/small business setup. A single PC wired into the lan and a handful of occasional use laptops & Android phones/tablets and a Playstation.My connection is a 30M down / 5M up cable link. I have a UBEE DOCSYS 3.0 cable modem operating in passthru mode to my RV110W.
Over the course of several days, thruput drops from the measured 30/5 down to as low as 1/whatever. Rebooting the RV110W restored full speed. The UBEE has never been rebooted during this time. Connecting my wired desktop PC directly to the UBEE modem give me the full 30 downlink speed even when the RV110W perfomance has dropped to 5 or even 1.
I am using onle a single wireless LAN, no logging turned on, no VPN, no other 'tuning of settings.As it is, this device must be rebooted every few days to restore full network speed. This is unacceptable, of course - especially from a small business class device!
Installation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
So I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View RelatedIn other words. If my cable modem only has 50 mbps is that all I will get out of my wireless router, even if the router has a higher mbps rating/
View 8 Replies View RelatedWhich is the wireless speed of this router? No speed infos are present in the official web site. In the web some sites say it's a 300, others say it's a 150, others 248...
View 9 Replies View RelatedI have a desktop and laptop here, the desktop being mine custom built wireless and all, and my buddies desktop.The issue that I'm having is that my desktop, regardless of wired or wireless gets 25 mbps down speed, and the laptop gets only 2.5 mbps down speed wired or wireless
View 4 Replies View RelatedI have 100 Mbps Half Duplex on one side of the Switch. ( Autonegotiation disabled )I have 10 Mbps Full Duplex on the other side ( Auto-negotiation disabled ). Should the link come up on both sides
View 4 Replies View RelatedI just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
i have a 100 mbps lan. but 1 computer works on only 10 mbps half duplex mode why??
View 4 Replies View RelatedSo every few minutes; in no pattern, my laptop internet will turn off then reconnect.I have noticed that it does it mostly at night where I am most active on my laptop.I am using a external wireless adapter to make my connection somewhat "better" but I am not sure if that is the cause.
View 1 Replies View RelatedJust replaced Dir 625 with Dir 655. I have Sony KDL 46NX700 TV. When the router is on the tv turns off and on, like a reboot. The longer the tv stays on the longer between the reboots. Also if the wireless device is turned off in tv settings it does not turn off and on. Have talked to Sony, they can't resolve the problem. Had me call local repair. He thinks it may be the power supply. He said he would order one. That was before I discovered it was the wireless signal causing it to turn off and on.
View 4 Replies View RelatedThis first started happening a couple of weeks ago when a piece of software was put on to the computer off an external hard drive. First the wifi would turn itself off but after turning it back on it might happily stay on for a few hours before switching itself back off.The day before yesterday it decided to start turning itself off straight away. I plugged in with ethernet, uninstalled the old drivers and reinstalled new ones, this didn't seem to do anything so I turned on my firewall and titanium defense and after a while it decided to start working again.Earlier today I connected my DSLR camera to my USB 3 port to download pictures, this killed my wifi straight way. I reconnected with ethernet and I'm not sure what I did but now the wifi has decided to work again.
View 4 Replies View Relatedjust three days ago my wi-fi quits working when the computer goes to sleep mode. The box in power management is unchecked. This seems to have started after a McAfee update that created screen blanking issues corrected by Dell and McAfee. I can find no reason so have turned off the sleep. Device driver is up to date.
View 3 Replies View RelatedI have a 2wire modem and I'm using att DSL. The internet was working fine, I went out of town for 2 days, I returned to find my internet wont work. During the time I was out my brother said it hadn't worked for the 2 days. The modem works fine and all lights are green when my desktop is turned off or not connected. It even lets my brother use wireless on his laptop. However, when I turn on my computer or when I connect it to the modem with an ethernet cord, the DSL light will go red and not work.
View 7 Replies View RelatedWhen I first got my DIR-655 (Hardware version B1) the Wireless would keep on turning itself off, and it needed a reboot of the unit to turn it back on again.After having upgraded to the 2.03NA version of the Firmware it seems to be working correctly and hasn't turned off for a few days now.
View 14 Replies View RelatedHe has a Linksys wireless router installed. He only uses the router for use with lap top for the wireless convenience around the house. The desktop PC is Ethernet wired;.
When both laptop and PC are shut off, and then he, in another room turns on the laptop, the Desktop PC start up all by itself.
Is there a setting on either of these PC or router that need adjustment?
I have this problem yesterday when I was surfing the internet when suddenly my belkin router turns off. This router is working just fine in the beginning when we have this. When I troubleshoot, it says about the ethernet cable. When I plug it to the ethernet slot on the back of my computer, it would not flash an orange light. Am I required to buy another ethernet cable or it's just my router who had just lost power?
View 5 Replies View RelatedDell Inspiron 14 3420
I have bee trying to make WOL work with no luck so far. The problem is that when I shut down my laptop (connected to AC power) the NIC also shuts down. I already unchecked the box "Allow this computer to turn off this device to save power" in the power management tab in advanced NIC properties.
I noticed that when I force shutdown my laptop (press the power button for 5 seconds), the NIC stays on and WOL works, but when I perform a regular shutdown, the NIC shuts down when windows shuts down.
We have one cisco core switch 6500 series which was configured portchannel on several gig interfaces. This port is used as a trunk to enable communication between VLANs. The VLANs is where several high-end servers/hosts reside.After we disable / unbind the portchannel, the port turns amber. The following is what we did on the interface
1-no switchport command
2- make the port as access mode #switchport mode access
3- shut and no shut
4- clear arp
5- clear mac
what else can we do on that particular interface. It is just on that particular interface, the rest are ok.
Essentially when my friends computer disconnects from the router, everyone elses computers cannot access the internet, even though windows says they are still connected.
View 1 Replies View RelatedI am connected to a public wifi in my building thru built-in adapter of my laptop. I am running Windows 7 Home Basic. The connection allows only one device to run on one login name. I need to share this connection with my other device by turning my laptop into hotspot or thru ethernet. I have tried using Virtual Wifi Miniport and Connectify. I have tried LAN also. But I encounter the same problem in all the cases. As soon as I turn on internet sharing thru the properties of my public wifi connection, the Virtual Wifi or the LAN turn "Unidentified" and there is no internet on my other device. I even tried using a usb wifi adapter to connect to public wifi and sharing the internet over my laptop's adapter and vice versa but to no avail.
View 1 Replies View RelatedMy WAP4410N AP is running version 2.0.2.1 firmware which is quite old. There are newer firmware releases available which I'd like to upgrade to (fix the known bugs, etc.).
So I upgrade my firmware from version 2.0.2.1 to any of the following versions:
- 2.0.3.3
- 2.0.4.2
- 2.0.5.3
The AP reboots and my settings are all still there.
I go to change any of the settings I have - DNS, Time Zone, PSK, any field which can be edited and click Save.
The Save takes place and the screen refreshes to the old settings - the new settings don't stay in place after the Save.
I've also factory defaulted the AP prior to the upgrade, upgraded and then been in the same place unable to save any changed settings.
System details:
Information PID VID: WAP4410N-E V02
Device: WAP4410N Wireless-N Access Point with Power Over Ethernet Software Version: 2.0.2.1
I have three pairs of ASA5510 firewalls, each pair configured as a failover pair. When each pair boots up, even if I boot up the primary first, when they are both up and the primary/active syncs to the secondary/standby, the primary always switches to standby and the secondary thus becomes active.
What would cause this? It happens on all three pairs. Does failover look for the highest ID or IP address to determine which of the pair will be active?
Apparently when watching TV after the show is over and the TV is turned off the lights on the router dims and their wifi router is not able to be found any longer and they have to reset the router in order to find it again. I downloaded the newest firmware version 4.21.5 yesterday since they had the original firmware from years ago thinking this may solve the problem. It worked for a day and then stopped with the router having the same symptoms. They have this router located very closely to their plasma TV for the past 3 months, however, I was reading that wifi routers do not cause any interference with plasma TVs. They had this router placed near their old rear projection TV for years and never had any problems.Could the router be going bad? Could the router be too close to the TV?
View 2 Replies View RelatedI have a DIR 601 with a actiontec GT701D modem.When I shut down my computer the globe on the router goes from green to orange.The modem people say their modems are always on Am I missing something on the DIR601?why?
View 5 Replies View Related