D-Link DIR-655 :: TV Turns Off And On When Router Is On
Jun 19, 2011
Just replaced Dir 625 with Dir 655. I have Sony KDL 46NX700 TV. When the router is on the tv turns off and on, like a reboot. The longer the tv stays on the longer between the reboots. Also if the wireless device is turned off in tv settings it does not turn off and on. Have talked to Sony, they can't resolve the problem. Had me call local repair. He thinks it may be the power supply. He said he would order one. That was before I discovered it was the wireless signal causing it to turn off and on.
View 4 Replies
ADVERTISEMENT
Nov 1, 2011
When I first got my DIR-655 (Hardware version B1) the Wireless would keep on turning itself off, and it needed a reboot of the unit to turn it back on again.After having upgraded to the 2.03NA version of the Firmware it seems to be working correctly and hasn't turned off for a few days now.
View 14 Replies
View Related
Dec 29, 2011
I have a DIR 601 with a actiontec GT701D modem.When I shut down my computer the globe on the router goes from green to orange.The modem people say their modems are always on Am I missing something on the DIR601?why?
View 5 Replies
View Related
Feb 18, 2013
Region : Canada
Model : TL-WR1042ND
Hardware Version : V1
Firmware Version : 3.14.4
Recently in the morning the router will have lost ability to connect to internet <internet light is on> and I cannot access the router page <sys light solid> from either wired or wireless connections. Why is this and will it be solved if I upgrade firmware?
View 2 Replies
View Related
Oct 30, 2012
I have this problem yesterday when I was surfing the internet when suddenly my belkin router turns off. This router is working just fine in the beginning when we have this. When I troubleshoot, it says about the ethernet cable. When I plug it to the ethernet slot on the back of my computer, it would not flash an orange light. Am I required to buy another ethernet cable or it's just my router who had just lost power?
View 5 Replies
View Related
Oct 25, 2012
Essentially when my friends computer disconnects from the router, everyone elses computers cannot access the internet, even though windows says they are still connected.
View 1 Replies
View Related
Mar 3, 2013
Apparently when watching TV after the show is over and the TV is turned off the lights on the router dims and their wifi router is not able to be found any longer and they have to reset the router in order to find it again. I downloaded the newest firmware version 4.21.5 yesterday since they had the original firmware from years ago thinking this may solve the problem. It worked for a day and then stopped with the router having the same symptoms. They have this router located very closely to their plasma TV for the past 3 months, however, I was reading that wifi routers do not cause any interference with plasma TVs. They had this router placed near their old rear projection TV for years and never had any problems.Could the router be going bad? Could the router be too close to the TV?
View 2 Replies
View Related
Oct 1, 2012
So every few minutes; in no pattern, my laptop internet will turn off then reconnect.I have noticed that it does it mostly at night where I am most active on my laptop.I am using a external wireless adapter to make my connection somewhat "better" but I am not sure if that is the cause.
View 1 Replies
View Related
Jan 24, 2013
This first started happening a couple of weeks ago when a piece of software was put on to the computer off an external hard drive. First the wifi would turn itself off but after turning it back on it might happily stay on for a few hours before switching itself back off.The day before yesterday it decided to start turning itself off straight away. I plugged in with ethernet, uninstalled the old drivers and reinstalled new ones, this didn't seem to do anything so I turned on my firewall and titanium defense and after a while it decided to start working again.Earlier today I connected my DSLR camera to my USB 3 port to download pictures, this killed my wifi straight way. I reconnected with ethernet and I'm not sure what I did but now the wifi has decided to work again.
View 4 Replies
View Related
Jan 9, 2013
just three days ago my wi-fi quits working when the computer goes to sleep mode. The box in power management is unchecked. This seems to have started after a McAfee update that created screen blanking issues corrected by Dell and McAfee. I can find no reason so have turned off the sleep. Device driver is up to date.
View 3 Replies
View Related
Nov 1, 2011
I have a 2wire modem and I'm using att DSL. The internet was working fine, I went out of town for 2 days, I returned to find my internet wont work. During the time I was out my brother said it hadn't worked for the 2 days. The modem works fine and all lights are green when my desktop is turned off or not connected. It even lets my brother use wireless on his laptop. However, when I turn on my computer or when I connect it to the modem with an ethernet cord, the DSL light will go red and not work.
View 7 Replies
View Related
Mar 29, 2011
He has a Linksys wireless router installed. He only uses the router for use with lap top for the wireless convenience around the house. The desktop PC is Ethernet wired;.
When both laptop and PC are shut off, and then he, in another room turns on the laptop, the Desktop PC start up all by itself.
Is there a setting on either of these PC or router that need adjustment?
View 6 Replies
View Related
Mar 28, 2013
Dell Inspiron 14 3420
I have bee trying to make WOL work with no luck so far. The problem is that when I shut down my laptop (connected to AC power) the NIC also shuts down. I already unchecked the box "Allow this computer to turn off this device to save power" in the power management tab in advanced NIC properties.
I noticed that when I force shutdown my laptop (press the power button for 5 seconds), the NIC stays on and WOL works, but when I perform a regular shutdown, the NIC shuts down when windows shuts down.
View 6 Replies
View Related
Jan 4, 2013
I am connected to a public wifi in my building thru built-in adapter of my laptop. I am running Windows 7 Home Basic. The connection allows only one device to run on one login name. I need to share this connection with my other device by turning my laptop into hotspot or thru ethernet. I have tried using Virtual Wifi Miniport and Connectify. I have tried LAN also. But I encounter the same problem in all the cases. As soon as I turn on internet sharing thru the properties of my public wifi connection, the Virtual Wifi or the LAN turn "Unidentified" and there is no internet on my other device. I even tried using a usb wifi adapter to connect to public wifi and sharing the internet over my laptop's adapter and vice versa but to no avail.
View 1 Replies
View Related
May 16, 2012
I have a 128mb connection with a sa 500 series fw/router. When I turn on the ips function my throughput drops to 15 Mbps and the CPU max goes up to 100%. What gives?
View 2 Replies
View Related
Sep 12, 2012
We have one cisco core switch 6500 series which was configured portchannel on several gig interfaces. This port is used as a trunk to enable communication between VLANs. The VLANs is where several high-end servers/hosts reside.After we disable / unbind the portchannel, the port turns amber. The following is what we did on the interface
1-no switchport command
2- make the port as access mode #switchport mode access
3- shut and no shut
4- clear arp
5- clear mac
what else can we do on that particular interface. It is just on that particular interface, the rest are ok.
View 7 Replies
View Related
Aug 21, 2011
Want to use WOL on 8300 with Broadcom Netlink card. Everything seems to be configured correctly: bios, network card, port forwarding etc. In fact I can wake up the 8300 over the internet following a complete shut down, but only if I do it within 3 secs or so, then it fires up OK. If I wait a little longer it will not respond to the Magic packet. I notice something strange which I suspect may be related: when I restart the PC, in the power management of the Broadcom card the box is checked that allows te computer to turn off the Broadcom card to save power, while I am sure that I unchecked it before shutdown. I suspect this setting is somehow overwritten by Windows. mentioned all BIOS setting are to enable WOL. As if Windows is ensuring that the Broadcom card is powered down so it cannot receive the Magic packet to initiate a startup.
View 8 Replies
View Related
Sep 29, 2011
So I have a Toshiba Satellite L555D-S7005. When I put it into Hibernate mode (I dont like turning it off, takes too much time) it paralyzes my whole wireless network. It makes it so that anybody else on WIRELESS gets disconnected, and cannot reconnect easily (they must restart the router). This gets very irritating when my brother is on the X-BOX/Laptop and he cannot continue playing games or whatever. If I disconnect my laptop the network goes down for them, but not for me. I can log right back on and connect with no problems. The wired computer has no problems with internet when I turn off my laptop.
View 5 Replies
View Related
Oct 16, 2012
My WAP4410N AP is running version 2.0.2.1 firmware which is quite old. There are newer firmware releases available which I'd like to upgrade to (fix the known bugs, etc.).
So I upgrade my firmware from version 2.0.2.1 to any of the following versions:
- 2.0.3.3
- 2.0.4.2
- 2.0.5.3
The AP reboots and my settings are all still there.
I go to change any of the settings I have - DNS, Time Zone, PSK, any field which can be edited and click Save.
The Save takes place and the screen refreshes to the old settings - the new settings don't stay in place after the Save.
I've also factory defaulted the AP prior to the upgrade, upgraded and then been in the same place unable to save any changed settings.
System details:
Information PID VID: WAP4410N-E V02
Device: WAP4410N Wireless-N Access Point with Power Over Ethernet Software Version: 2.0.2.1
View 4 Replies
View Related
Mar 22, 2011
I have three pairs of ASA5510 firewalls, each pair configured as a failover pair. When each pair boots up, even if I boot up the primary first, when they are both up and the primary/active syncs to the secondary/standby, the primary always switches to standby and the secondary thus becomes active.
What would cause this? It happens on all three pairs. Does failover look for the highest ID or IP address to determine which of the pair will be active?
View 1 Replies
View Related
Jan 30, 2013
Region : Others
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP :
After I configure the WAN setting on TL-MR3020, my laptop unable to connect to my TL-MR3020 anymore, the message says "windows was unable to connect to TP-LINK_POCKET_3020_B5F9AD".
View 2 Replies
View Related
Feb 16, 2013
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
View 4 Replies
View Related
Dec 27, 2011
I can't log in to my router settings because my CAPTCHA just displays a red x.to sign up for this forum the CAPTCHA worked....
View 4 Replies
View Related
Jan 29, 2012
I have a TP-Link (TL-WR941ND) wireless router in my living room and I want to expand my connectivity to get to the bedrooms area. I have a D-link (DI-524)wireless G router I want to take advantage of. How can I connect the two routers (no cables to be used) together so I can have acces to the internet from my room?
View 1 Replies
View Related
Nov 24, 2011
I have a buddy who owns a bar and wants to install a insecure wireless router for his customers downstream from his SBC Global ATT Modem/Wireless Router combo.
-Modem/Router Combo: Actiontec GT724WG
-Downstream Unsecure Wireless Router: D-Link DIR-651
He says has 3 static ips for the modem, and 1 of the network cables coming from the modem directly into the D-Link Router. I first attempted to just plug it into the uplink, and let DCHP do its magic, but I had no luck with that. I could connect to the router but it didn't have internet.
So I restarted the downstream router, and plugged the network cable into the 1st port, and suddenly I had internet on the wireless but it would constantly go up and down, and ping times were extreme erratic.
View 8 Replies
View Related
Feb 3, 2013
I have a weird problem. I bought recently a new router, and when I try to connect to the settings on it on http://198.168.0.1 it sometimes works, mostly doesn't. When I ping other devices which are connected it, it's the same; sometimes get a response, mostly I don't. The router model is: TP-LINK 150Mbps Wireless N Router TL-WR740N, The thing which it's connected to is entitled "ADSL2+ Ethernet bridge router" That aforementioned thing is suppoused to be a modem. But, when I try to connect to its settings from http://10.0.0.138 , I'm able to, and other who are connected to the network give response to a ping.
View 4 Replies
View Related
Mar 14, 2013
Region : India
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 3.13.27 Build 121206 Rel.60215n
ISP : TataDocomo 3G
I am having problems with my TL-MR3420 router, it disconnects WIFI all the time. My ZTE MF 631 dongle gives me a strong signal and stable connection and rarely loses connecton when plugged directly into my laptop. With my MR-3420 V2 losses connection, duration only lasts for about 2 to 3 minutes. I have to power off/on the router and turn off/on the wireless button on the laptop to restore connection or manually disconnect in the web interface of MR -3420 and reconnect.
Even i tried the changing channel bandwidth and channel, still no luck. Router settings is pretty much default, expect security key. I have quite recently upgraded to the latest firmware but the problem seem not to have been resolved.
View 4 Replies
View Related
Feb 7, 2013
Region : Turkey
Model : TL-MR3020
Hardware Version : Not Clear
Firmware Version : (120817)
ISP : turkcell
I have recently purchased the portable TP link 3020 which is a great solution for me in order to get wifi for multiple users till I get through the long process of getting ADSL in Turkey.The thing is that the 3G bundle Turkcell provided me with is not identified by the modem, so I looked it up on the internet and I found out that I needed to add the bin of the bundle, I searched within the list published on TPLINK website but without any luck.... finally I found the bin I was looking for in another country list... mine is Huawei E353 and the one I found is Huawei E353s2. Anyway I added the bin and still not luck identifying the bundle, I finally resorted to upgrade the firmware which I hate because I always worry of the bad consequence of failure, and unfortunately I was right! Once I upgraded the firmware, I couldn't get connected to the router, it keeps asking me for the key, but without any success! I tried hardware reset by holding the WPS button for 5 seconds as suggested in the manual, but any further success!
View 1 Replies
View Related
Jan 15, 2013
I am wondering if there is a way to limit traffic through the router. The problem is that one person downloads something, they hog up all the bandwidth, and end up creating lag on other people that may be gaming. So I am wondering if there is a way to limit traffic to 500kb/s per connection..(wired or wireless).. I have a DIR-815 D-link router, and have looked through the settings but I don't see anything off hand that might be related but I could have missed something.
View 15 Replies
View Related
Feb 12, 2013
I have a DIR-615 and ATT is giving a pppoe static subnet, meaning they will hand me a /29.All I need is a static IP. I don't need a subnet. NAT is fine. But ATT will only give a subnet.So if I try to use this pppoe with /29 connection with a DIR-615, will it work? What will be the WAN IP of the router? Will it be the first usable? I don't see where I can define the WAN interface IP.
I can use a dynamic IP with Dlink DDNS if necessary. Or How to do whatsmyip and tell it to me, and I can access the router with that, if need be.
View 7 Replies
View Related
Sep 1, 2011
She lives in a big house so what I have done is used a tp-ling adsl router (router 1)at one end of the house with a ip address 192.168.1.1 a cat 5 cable runs to the other end of the house with a TP-Link wireless router (router 2) at the other end of which I have changed the ip address to 192.168.2.1 as it was conflicting with the first router (they had the same ip).So I connected one laptop to the router 2 and it connected to the internet no problem. I did an ipconfig and its gateway was 192.168.1.1 (router 1). I connected a second laptop and straight away it connected to the internet and had the same gateway ip.I try to connect a brand new laptop and it wont connect. It can only see router 2 (192.168.2.1) I have ping'ed 192.168.1.1 but its not accessable. I have gone into the dhcp and changed the default gateway to 192.168.1.1 on the laptop but still won't work.It must be a setting on the new laptop that needs changing. Its on W7 home.
View 8 Replies
View Related
Jul 11, 2012
Today I bought a new TP-Link Wireless Router in China, (TL-WR845N), and set it up with followed instructions with the router IP setup too with 192.168.1.1. Before, it was only LAN and now I bought the wireless to use my iPhone with it. Now LAN wont work at all on either of my computers. I've uninstalled and reinstalled the Ethernet drivers, rebooted/checked the modem and router, but still couldn't get it to work. My Windows XP shows connected, but Chrome says unable to connect to the Internet.
I've checked TCP/IP settings, made it automatic, still nothing.
View 14 Replies
View Related
Oct 30, 2011
So my old D-Link (DI-524) just conked out and for some reason will no longer give a wireless signal. I'm looking for an affordable router that will work for 1) hardwiring into my xbox for some gaming and mostly Netflix and 2) give a solid connection to my MacBook in the home with maybe one additional laptop connection at times. Having the ability to stream music on speakers would be a good plus considering future stereo purchases.
View 5 Replies
View Related
