I'm looking to use 861s at few remote sites connecting to a 881 in the main office using Easy VPN. If I was to get 2 ISPs at the main office, can I configure it in a way that if the primary WAN failsover to the secondary, the VPN tunnels from remote sites will also failover?
Would you recommend an ASA 5505 at main office over the 811?
Is it possible to configure Easy VPN on brach side which has 877 series router and ADSL connection for internet such a way that for internet traffic it will use the local ADSL line and for the server in HQ it uses the tunnel.or for internet also it will go thrugth tunnel and uses internet link at the HQ?
View 3 Replies View RelatedI am looking for the procedure of the router 3900 series failover. I have got two 3900 series router with the same ISO and other interface cards. What are the main things that I should watch ? Does the standby router takes the same ip of active router if the active router fails ? How should I configure it.
View 1 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedI'm currently using DynDNS for my Dynamic DNS Provider with the RVS4000, but I'm looking at upgrading to the RV180 and switching my Dynamic DNS provider over to DNS Made Easy since I can get all my DNS hosting under one roof. Does the RV180 support DNS Made Easy in its Dynamic DNS client? If not, could it be added in a firmware update?
View 3 Replies View RelatedThe first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.
View 3 Replies View RelatedI have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
View 1 Replies View RelatedI have 2 Cisco routers 3945. Use HSRP for links failover. Does exist any possibility (any protocol) which makes routers configuration's automatic synchronization (as failover for ASA firewalls)? I mean, if I will make any configuration changes on the Active router, automticly will taken this changes by the Standby router.
View 3 Replies View RelatedI’m currently training to take my CCNA, So for the reason I’m here, I have just been asked to take over the company network.And I need to know how I go about configuring some base level routers.I have 3 remote sites and 1 main site, all these routers are using 857’s, with a VPN tunnel between them, this is running all OK and working fine,But my boss has decided to have a second ADSL line installed in the main site for failover.How do I go about configuring this, ie how do the VPN’s terminate on the other router when the main one goes down?
View 1 Replies View RelatedIs it possible to have this setup on RV016?
WAN1: VOIP traffic (either by port or IP) + failover for WAN 2 WAN2: all other traffic + failover for WAN1 WAN3: failover for WAN1 & WAN2 with connection on demand
I have an issue where we have a single ASA5505 [soon to be active/standby with single ISP] connecting to HQ where there are 2 x Cisco 2821's. Each 2821 router has it's own connection to the internet running BGP and each router is setup to terminate IPSEC VPN's from the ASA. The ASA has a backup VPN configuration with no IP SLA configuration to track if the Primary IPSEC endpoint is alive. Keep alives are set and the VPN does failover to the backup.When the primary 2821 internet connection fails the ASA fails over to the backup 2821 and everything works a dream. However when the primary internet link re establishes to the primary 2821 the ASA does not fail back to the primary 2821 it stays on the backup 2821 and all is broken as the remote site starts forwarding traffic out the BGP default route - which is back via the primary connection...How do I fix this so that the ASA tracks the IP of the primary router to failback without manual intervention - clearing isakmp and ipsec sa's?The other issue is the ASA does not allow traffic to be orignated from the 2821 end of the VPN. You have to establish traffic from behind the ASA for the IPSEC sa to be created.
View 1 Replies View RelatedWe are looking at purchasing and RV042 soon and have one cruitcial question. I am looking at having two internet connections running into the RV042. The only load balancing is going to be that all the VOIP traffic will go through one connection (eg WAN2) and then have all other traffic (such as web and email) through WAN1.
I am looking to have it so that if one of the internet connections goes down then it will failover EVERYTHING to the one that is working so both the VOIP and all the other traffic share the same connection until both WANs then go back online.
I have an issue with configuring the VPN Stateful failover between two cisco routers 3845. The stateful HA is not up.
Below is the topology
Configuration on HA-1
interface GigabitEthernet0/0
ip address 194.170.9.183 255.255.255.240
ip accounting output-packets
duplex auto
speed auto
[code]....
I was wondering how does failover works on Cisco Small Business RV016. Specifically, I am interested when one WAN line stop working, and all the computers in the LAN start using another line. Does it means that IP addresses of the computers in the LAN will change, or they stay the same? If they change can I set it up that they always stay the same no matter which input WAN they are using?
View 1 Replies View RelatedIPSEC VPN between 2851 routers. I have 4 routers 2 at each site using HSRP on the front and I need to encrypt traffic between. My concern is the failover portion.
View 2 Replies View RelatedRV042 in Router mode.WAN1 preferred.With Smart Link it seems to work to a point.When WAN1 fails, it fails over to WAN2.But then it gets stuck on WAN2 and I have to manually switch to WAN2 preferred and then back to WAN1 preferred to get WAN1 connection to return.The test IP addresses should be just fine as set.
Is there something I should be doing differently?
Have a 1921 that has 3 eth connections (1 LAN, and 2 WAN) - I have 2 seperate OSPF processes (2 areas) on the WAN Ints - both upstream WAN's are sending defaults back to the 1921, and the 1921 is sending it's LAN range to them.
I have ip ospf cost 150 set on the "failover" WAN connection interface (Both on the 1921 and upstream), but the 1921 is preferring the default route from the "failover"?
The default routes are both being received by the 1921, but it's preferring the "failover" Int with the ip ospf cost 150 configured?
I'm just courious as to the platform specs of the SRP500 series routers. What processor is used, how fast is it and how much RAM and flash do they have?
View 4 Replies View RelatedDoes the two listed POE switch ports on the 880 series routers are active out of the box (default) or is configuration or extra parts required as internet pictures appear to show what looks like a power connector new to the POE ports?
View 8 Replies View RelatedTomorrow 2012-06-06 is ipv6 launch day, what about ipv6 on srp500 series ? On product specification cisco wrote : IPv6 (RFC 6204) ready.
View 10 Replies View RelatedI'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.
View 1 Replies View RelatedI have been able to put two Linksys routers in series no problem but this doesn't seem to work with an RV042.I have a number of customers that need to connect to a private email network via a router based VPN, but since VPN traffic is not filtered in the firewall, I would like to use an older Linksys router to manage the VPN(s) and have it pass data in through the filters of an RV042 on the DMZ port.I am getting stuck on the very frist part of this. Although I can connect to both the RV042 and LinkSys directly (by adjusting my subnet), I cannot ping the Linksys when it is connected through the DMZ port even if I disable the RV042 Internet port.
I know both the Internet and DMZ ports work on the RV042. I suspected that perhaps the RV won't pass through private IPs and tried known available pubic IPs instead of the 192.168.2.x subnet, but still no ping.What would be limiting the RV in this case? Is is possible to setup the RV to work in series with another router? Is there any other way to filter VPN traffic?
What is the difference between the family series SA 520 and the family series SR 520?, technically of course.
View 4 Replies View Relatedi have a demroom set up which includes a sr520 as the edge router connecting to the ISP and i have a uc 560 connected to that which is working fine i also have a new business edition 3000 and a 800 series router which im looking to connect to the sr 520 for access to the ISP as the 800 series doesn't have a ADSL line on it .i have given the 800 series routers wan interface a static address of 192.168.75.14 wich is from the address range in the sr520s default vlan and excluded the address from the DHCP pool. now from the ccp express on the 800 s i can ping the wan port of the 800 s and the default vlan/gateway of the sr520 and the wan ip of the sr520 but no further also once i try pinging it from the cmd on windows i cant ping any further that the wan interface on the 800 s .
View 2 Replies View RelatedDoes any one used third party SPF in Cisco ASR 1002 series routers, does it supports them.
View 2 Replies View RelatedI've goggled and searched here, and I can't seem to find what I'm looking for. I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.
View 2 Replies View RelatedNormaly all incoming IP addresses can use NAT to gain access. I would like to make a rule that only one IP address can connect to my router and use that port or range of ports defined.
Is there a way to configure a SRP 527W on such a way?
If not possible now, can I expect a software update ?
what is the maximum number of Lan-to-Lan and user vpns supported in the ISR G2 2911 and 2921?
View 5 Replies View Relatedwhich 800 series routers allow 20 Mbps throughput across the WAN port? I have a cable modem that outputs this speed but am having difficulty finding a router that will accept this throughput across the WAN port.
View 21 Replies View RelatedI wondered, how much power do the SRP520-U series actual draw? Compared to commonly used home-grade equipment I think the power consumption is above average?
View 1 Replies View RelatedWe have deployed a number of 800 series routers for some of our clients and have found that in many cases they seem to disconnect at an excessive rate. When I connected to the console of one the other day I could see that the virtual-interface for the ADSL connection was down, but not the ATM or DSL interface. If I disconnected the cable and reconnected the virtual-circuit came back up momentarily before disconnecting within a minute.
If I switched off the router for a few minutes and powered it back on it would usually remain up for a few hours. I reconfigured the router again using exactly the same config and it seemed to stay up for quite long periods for 4 or 5 days before reverting to type. [code]
We have an MPLS network to a half dozen remote sites. At our main location we have a 2800 series router. In the routers config are the following lines for QOS. When I go to the routers on the other end of the MPLS, none of them are configured with these same policies. Would these not be in the running config of the 1800 series routers, or is this not setup correct and this should be removed?
View 13 Replies View Relatedwhat is the throughput of the 1941 and 3945 series routers, i didn't find this info in the datasheet for both!
View 2 Replies View Related