Cisco Switching/Routing :: 7200 Bkp Router Can't See Master
Jul 30, 2012
I am experiecing issues with HSRP.I have two 7200 core routers connected via one portchannel layer 2 and i set up the HSRP.The switch 01 is the master and 02 is the bkp.the problem is, the bkp router can´t see the master and there are a lot of loggs with active-speak and can´t see the master. the configuration are ok, i just check and recheck but there are no mistakes. [code] the configurations are ok, but the router can´t see each other, just in the vlan 500 the other vlans are ok.
View 7 Replies
ADVERTISEMENT
Aug 22, 2009
Don't know if this is right section of NetPro forum to bring up my problem. I have 871 router configured as NTP master. It works as a gateway for a small windows network with a domain controller. I want DC to pull the time from the router and configured the router as follows:
Code...
View 23 Replies
View Related
Jan 30, 2013
I would like to know if it's possible to change a master in a 3750 stack without rebooting it?I searched in Cisco documentation, in the forum, and I googled it but I didn't find anything.
View 3 Replies
View Related
Apr 18, 2012
We have a stack of a 3750E with a 3750X, when we turn off the master, a disconnection occurs for around one minute while only one request timeout is seen when the slave is turned off. Is this normal? Details: in other words, when the slave switch is elected as the new master all the port-channels and some physical ports become in 'down' state before reobtaining the up state again, this results in a one minute outage. The question is: is it normal to have a layer2 control traffic interruption when the master fails and re-election occurs and if yes, what is the normal downtime in seconds. the layer2 control information such as port-channels LACP protocol are not synchronised to all slave switches by the master?
View 7 Replies
View Related
Jun 13, 2012
About an hour ago I had the master switch on one of my 3750x (WS-C3750X-48PF-S) stacks crash. The only two items we've found that could have caused this issue are the roughly 1.3 million big buffer misses and several of the following in the syslog
SLT:WARN:No exporter configured for smartlog! I do not have smartlogging turned on, nor is there a netflow exporter configured
sh logging smartlogsmartlog is disabledsmartlog exporter:smartlog pkt length: 64 Total pkts processed: 0Total DHCP Snooping pkts processed: 0Total DAI pkts processed: 0Total IPSG pkts processed: 0Total ACL pkts processed: 0
I did not see any traffic spikes prior to the crash.
This stack has been stable since it's last IOS upgrade from 12.2(58)SE1 to 12.2(58)SE2 back in October 2011 so this has me a little worried.
View 3 Replies
View Related
Feb 12, 2013
Setting up NTP. Currently the source for NTP within our network is our core 6500.Currently the NTP source for the 6500 are internet based NTP Servers. I would like to configure the 6500 to respond to NTP messages as the NTP Master. However will the 6500's source remain as the internet based NTP Servers?? In other words if the 6500is configured to be NTP Master, where would it get it's time from?
View 5 Replies
View Related
Feb 27, 2013
I have two like switches in a stack (WS-C3750G-48PS 15.0(1)SE2 C3750-IPBASEK9-M). Switch#1 is the master and is the one that needs to be replaced. Can I force Switch #2 to be the master, then power down switch#1, remove switch#1, insert the replacement, and then power on the newly added switch without shutting down or rebooting switch#2?
View 3 Replies
View Related
Oct 18, 2012
We have 2 3750 24 port fiber switches in a stack and we would like to change the member to become the master. Both are running the same IOS and they are alive on the network. I read that you can change the who becomes the master by setting the priority number higher on the member, which we did. However this requires a reboot of the member to take effect. Is there a way to force this without having to reboot? One other note, both switches in stack have a single gig connection that goes to the core (6500). One gig link is blocked due to spanning-tree and this is on the member that we want to become the master.
View 3 Replies
View Related
Jun 4, 2012
I have a stack of 2960S (c2960s-universalk9-mz.122-55.SE2.bin) and the master has failed (used to have a priority of 14). The second switch has become master (priority 1) as can be seen below: [code]
If I connect a new blank 2960S (same IOS) through the stack ports, will the master sync its config to the new one without causing problems?As I understand the new blank switch will also have a priority of 1 and will by default be numbered as 1. So if the config is correctly synced and I later on want to make switch 1 the master, I need to set the priority: [code]
View 4 Replies
View Related
Apr 10, 2013
I'm trying to do a Master reset on my Catalyst Express 500 (WS-CE500-24TT v01) and I'm having troubles with this. url...I do everything as it says, but when I plug the cable and I pull up the Web browser nothings appear, just the message that I don't have a Internet connection. The LED port on switch don't stop blinking as LED setup either. Is there another way to do the master reset?
View 0 Replies
View Related
Jul 18, 2012
I have 2 x 3750 stacked, the port number of the master switch is gigabitEthernet2/0/1, slave as gigabigEtherent1/0/1.
Can I change the port numbering so that the master switch gets GigabitEthernet1/0/x?
View 4 Replies
View Related
Dec 27, 2012
recently i removed the squid cache from the 7200 router so that i could apply the Qos on the router my topology is simple i have 7200 with two working interfaces
GI0/1====>LAN
Gi0/3====>to isp and working bgp
have 550 Mega BW from isp . at the rush hour , the quality of browsing becomes worse .i just need a Qos to apply it on the 7200 router so that the priority for my traffic as follow:
1- browsing has the highest priority
2-youtube has the 2nd priority after browsing
3-download & other applications have the 3nd priority.
View 8 Replies
View Related
Apr 26, 2013
i want to ask , how to match youtube in my qos, i want to give youtube the best priority in the rush hour. currently im using an acl that match the ips of youtube but i think its not sufficeitt :
View 5 Replies
View Related
Jul 23, 2012
router 7200 (12.2(33)SRE1)
two interfaces with traffic going through, placed in a Data-VRF
Another physical interface and loopback interface in the global routing-table.
ip flow ingress on all physical interfaces configured
It was running for at least a year: I was getting netflow packets on my analyzer from the box. Since a couple of weeks I get no netflow-packets anymore.debug ip flow export tells me "IPFLOW: Sending export pak to ... port 2055"
But the packet is not leaving the box. By setting up an ip sla monitor udp-echo I simulated some traffic (udp/2055) which is leaving the box.
[code]...
View 2 Replies
View Related
Apr 17, 2012
I have voice Bandwidth on Cisco Router 7200 and catalyst 3750.Now i want to sell some BW ( 15MB ) to any cleint. How to do that .We have Ethernet connectivity with my cleint.How i restrict client to 15MB. Will i have to form any VLAn or just port limit with bandwidth and which is better way?
View 8 Replies
View Related
Feb 1, 2012
What is the installation time for the Network Processor engine is:
NPE-G2=7200 series NPE-G2 engine with 3 GE/FE/E ports ,Do you reckon it can be done in two hours?
View 1 Replies
View Related
Mar 13, 2012
I have too much output drops in my cisco 7206 VxR NPE G1 router. I'm doing dot1Q on this interface and is connected to switch , i changed the router and IOS but still the error is same . What can be the reason . The interface on switch and router are 1000/Full and i changed the cable also . The traffic only comes about max70Mbps and it is really confusing. [code]
View 9 Replies
View Related
Dec 20, 2011
I have made some test and i noticed that qos input policy does not classify the icmp packet based on their dscp.The "match dscp ef" or "match precedence 5" is not working only the "match protocol icmp" shows hits.
We need to classify the different icmp packets based on dscp ( TOS ) for measurement purpose.CISCO 7200, 12.4.25d and 12.4.20T have a same behavior.
View 6 Replies
View Related
May 22, 2012
I was looking to setup a y configuration of routers with a modem going to master router, then from the mater router LAN ports to two other routers wan ports to give a guest and private network. I understand that this will all work fine for normal web surfing but can be very long winded when setting up port forwarding which i would need on the private network so I was wondering if I could get around this by setting up a DMZ on the master router for the private network router allowing all the port forwarding to be taken care of by just the one router. Would this work and would the two networks still be secure from one another.
View 8 Replies
View Related
Dec 30, 2011
I am considering the e4200 Vs the Asus RT-N56U router -- if " download master" type of functionality possible with the e4200 ?(Its a little app that comes with the asus router that allows you to download files directly to the USB storage even after the computer is switched off)
Could I do something similar with the e4200 ?
View 1 Replies
View Related
Sep 28, 2012
I have EA4500 acting as a router on domainless all-Windows network of two XP machines.Unfortunately, EA4500 aggressively grabs the role of the Master Browser (I am talking about Computer Browser Service) on the network (regardless in which order you power the devices up) and then doesn't serve as a working Master Browser - both Windows machines stop listing the network computers in the "Network Neighborhood" and incur massive timeouts when attempting to view the listing.A quick look with 'browstat.exe status' reveals that indeed the router has announced itself as a Master Browser device, but returns errors when you query it.Quite predictably, without the router, both machinces figure out amongst each other who will be the Master Browser and everything works fine. The problems begin only when you add the router to the network.
1) Is there any way to make EA4500 work like a full-blown Master Browser (the one that not only announces itself, but also serves as such)? having a Master Browser integrated in "always-on" router would really improve the predictability of the network.
2) If not, is there any way to disable the Master Browser on EA4500? For now I managed to achieve that by assigning the router to different workgroup name, but this is lame, as I now can't connect a disk storage to the router and use it within the same workgroup.
View 9 Replies
View Related
Jul 2, 2012
What are the rough figures that a NPE-G2 is able to hold for the BGP routing table?
378475 network entries using 51472600 bytes of memory 378482 path entries using 21194992 bytes of memory 63008/63003 BGP path/bestpath attribute entries using 8065024 bytes of memory BGP using 82975730 total bytes of memory
Are these 3 memories different memory allocated or are they are a sub-set of each other? If a NPE-G2 has 1GB RAM, does it mean that the routing table limit is depending on the RAM availability?
View 1 Replies
View Related
Feb 9, 2011
OSPF-4-ERRRCV: Received invalid packet: Bad LLS Checksum with one of our tunnels
View 1 Replies
View Related
Jan 2, 2011
My company has a spare 7200 VXR, originally planned to be placed on our TDM network. This plan was not followed through, but I'd like to switch it's function to work as a core router on our BGP network. I'd like for this 7200 to be able to handle full routes from our eBGP peer, something the SUP module in my 6500 isn't capable of doing. What kind of SUP module should i look at replacing this 7200 VXR with?
View 5 Replies
View Related
Mar 1, 2011
how many GRE tunnels (without IPSEC) can 7206 router supported. I have low bandwidth 2000 links & i want to configure GRE tunnels for them.
View 1 Replies
View Related
Jun 7, 2011
I have 7200 Router some flows are not forwarded and when i check ""show ip cache flow"" output i found the destination interface is going to Null i checked the access-list it permits these flows.
View 3 Replies
View Related
Sep 12, 2012
One of my customer is looking for 1 port OC3 card for 7200 series router. There are two options (PA-POS-2OC3/PA-A6-OC3)However my customer is not sure whether he wants a ATM/POS card.
How to determine whether i should go for ATM or POS Card for OC3. Or atleast what should be my approach to determine whether i should go for ATM or POS Card for OC3.
View 4 Replies
View Related
Dec 6, 2012
I have on 7200 series router with NPE-G1 module which is facing high CPU utilization. I have not found any particular process causing this high CPU utilization as it is caused due to interrupts. I have already enabled fast switching by "ip cef" command. Please suggest how to normalize the utilization as it is impacting the network and causing slowness. Please find below the output of show process cpu and also find attached the show tech of the device. Also let me know if any other output is required.
[CODE]...
View 14 Replies
View Related
Jan 24, 2012
We are running ISP and now a days we have many spam in our network, we want block the SMTP port 25 block on Cisco router 7200. So we can block the spam in our network.
View 3 Replies
View Related
Dec 12, 2012
I am having some issues with creating an ACL for my gateway router.I want to block external access to my network 192.168.1.0/24 from internet so i set up the ACL on the WAN port of my 7200 router asI am using named extened access list -
{
deny ip any 192.168.1.0 0.0.0.255 log
permit ip any any
}
and i applied this inbound accesslist on the WAN port of router as
"ip access-group acl-in in"
Now i have blocked the external traffic to my network 192.168.1.0/24 but the issue i am having is i am also unable to reach outside now. All i want is to block external traffic on the router WAN port but allow internal traffic to outside. Did i miss anything in the access list?
View 5 Replies
View Related
Apr 5, 2013
I am facing a problem when configuring the ipsec vpn on my 7200 router. [code]
View 5 Replies
View Related
Nov 19, 2011
I am getting the following message while trying to configure WCCP redirection on my 7200 router.
I have added this router to the routerlist of the WAE edge device. Ping is successful, but the following problem prevails.
NASCM-MPLS#show ip wccp
Global WCCP information:
Router information:
[Code]....
View 1 Replies
View Related
Aug 29, 2012
I have a CAB-OCT-V35-FC cable in my Cisco 7200 router and not all of them are utilized. I have to connect another site with a point to point leased line and I am planning to use one of the ports in my Cisco 7200 router which is using the CAB-OCT-V35-FC cable. My problem is both the cable end and the modem is V.35 female connector and both are DCE. I need to build a crossover cable of V.35 male to male which will connect the Cisco 7200 router and the modem.
View 2 Replies
View Related
