Cisco Switching/Routing :: How To Apply Qos On 7200
Dec 27, 2012
recently i removed the squid cache from the 7200 router so that i could apply the Qos on the router my topology is simple i have 7200 with two working interfaces
GI0/1====>LAN
Gi0/3====>to isp and working bgp
have 550 Mega BW from isp . at the rush hour , the quality of browsing becomes worse .i just need a Qos to apply it on the 7200 router so that the priority for my traffic as follow:
1- browsing has the highest priority
2-youtube has the 2nd priority after browsing
3-download & other applications have the 3nd priority.
View 8 Replies
ADVERTISEMENT
Dec 7, 2011
Access-group only allows me to set the mode.access-group > mode > prefer > port > int g2/1,Those are the only options available to me, it doesn't allow me to go.ip access-group <name> in or out or access-group <name> in or out.
I realize the commands may be a little off, I don't have a switch nearby. When I get on our 3750 there are no issues, it allows you to apply the ACL the conventional way. I just can't seem to find any way to apply an ACL on an interface on the 6506 though.
View 1 Replies
View Related
Jan 31, 2013
i want to apply a QOS for my trafic LAN, in my ASR 1001 , the LAN is connected with ge0/0/0 interface and it configured with the service instance to bridge vlan 1 ( i do that for OTV ) i put service policy in "service instance 1" to marking data with ef31 but i noticed that the class "plateform_datacenter" match the trafic and the ACL associate to this class not mach any trafic trafic !
tha policy-map march trafic for Datacenter :
sh policy-map interface gigabitEthernet 0/0/0 service instance 1
GigabitEthernet0/0/0: EFP 1
Service-policy input: MARKING-OTV
Class-map: Platforme_DC (match-any)
[code].....
View 9 Replies
View Related
Feb 15, 2012
configuration of NAT on an ASA 5520. On the ASA I have 1 x WAN connection and 1 x Internet Connection as well as the Inside and DMZ. I want to translate traffic from certain subnets on the inside (say 10.1.2.0 255.255.255.0) to an outside address (say 1.2.3.0 255.255.255.0). I'm assuming the ASA using the number after the brackets to distinguish what to translate? So if I had another entry with a '2' after the brackets, any of the '1' entries wouldn't translate to this? I have access-lits inbound on the INSIDE interface, I'm assuming these are applied before any NAT and only items allowed through the access-list are allowed to NAT?
I also have an address I would like to statically NAT with a certain port number, how do I do this? After I've configured this, what are the commands to apply NAT on the interface?
View 9 Replies
View Related
Mar 21, 2013
I got this 3640, trying to apply a service-policy (output and input), but seems like I do it something wrong...because he only apply the output policy... here the config, I already try to config the service police inside the fa0/0, but is not showed at all, he only show the output, its like I never apply that
View 1 Replies
View Related
Nov 1, 2011
I've set up my 3560 to do routing. Now, I'm looking for a way to apply acl restrictions to the vlan interface ip address itself.
View 1 Replies
View Related
Apr 22, 2012
Here is my configuration below , i have upgraded my C-3750 switch IOS from IPbase to IPservices , after upgrading i have tried to apply PBR on my Vlan 4 and failed , when i am tying to apply route-map to Vlan4 the command was taking but i am unable to see the route-map when sh run , i am giving the command as "ip policy route-map TTSL" in my Vlan4 , below is the configuration.
In Vlan2 i have connected one ISP and Vlan4 I have connected one ISP , my local subnets are 192.168.1.x and 192.168.2.x , now i want to route the 192.168.1.x traffic from Vlan2 and 192.168.2.x Traffic from Vlan4 .
sh boot
coreswitch#sh boot
BOOT path-list : flash:c3750-ipservices-mz.122-35.SE5/c3750-ipservices-mz.122-35.SE5.bin
[Code].....
View 9 Replies
View Related
Jul 30, 2012
I am experiecing issues with HSRP.I have two 7200 core routers connected via one portchannel layer 2 and i set up the HSRP.The switch 01 is the master and 02 is the bkp.the problem is, the bkp router can´t see the master and there are a lot of loggs with active-speak and can´t see the master. the configuration are ok, i just check and recheck but there are no mistakes. [code] the configurations are ok, but the router can´t see each other, just in the vlan 500 the other vlans are ok.
View 7 Replies
View Related
Apr 26, 2013
i want to ask , how to match youtube in my qos, i want to give youtube the best priority in the rush hour. currently im using an acl that match the ips of youtube but i think its not sufficeitt :
View 5 Replies
View Related
Jul 23, 2012
router 7200 (12.2(33)SRE1)
two interfaces with traffic going through, placed in a Data-VRF
Another physical interface and loopback interface in the global routing-table.
ip flow ingress on all physical interfaces configured
It was running for at least a year: I was getting netflow packets on my analyzer from the box. Since a couple of weeks I get no netflow-packets anymore.debug ip flow export tells me "IPFLOW: Sending export pak to ... port 2055"
But the packet is not leaving the box. By setting up an ip sla monitor udp-echo I simulated some traffic (udp/2055) which is leaving the box.
[code]...
View 2 Replies
View Related
Sep 25, 2012
I need to apply DHCP snooping on 4500 series switches working as L2 in my Network. We have external DHCL Server in another location connected with 6500 series switch.
Running EIGRP Configured Voice & Data Vlan both
DHCP Server -------- 6509 switch<----------------------------------->6509 Switch -------- 4500 switch ----------------------------------------------------------Ip Phones.
(ving Redundant) (ving Redundant)
I need to know whether the configuration which I mentioned in scenario is enough for apply DHCP snooping in my network.
View 4 Replies
View Related
Jul 9, 2012
Example config
int g2/24
service-policy output test
#and/OR
int g2/24.10
encap dot1q 10
ip address 10.1.1.1 255.255.255.0
service-policy output test
View 5 Replies
View Related
Sep 15, 2011
I have a 4510R-E chassis with SUP7-E running IOS XE version 3.01.01.SG. I am unable to create a port-channel and apply auto-qos for VOIP.If I configure auto-qos on the physical interfaces, I get this message when I try adding them to the port channel:
"The attached policymap is not suitable for member either due to non-queuing actions or due to type of classmap filters."
Auto-qos is not an available command in the port-channel interface configuration, but if I try adding the service policies that were created by auto-qos to the port channel manually, it lets me apply the input policy but on the output policy I get this message:
"A service-policy with queuing actions can be attached in output direction only on physical ports."
With the input policy applied to the port-channel interface, I tried addign the output policy to the physical ports and I got this message:
"A service-policy with non-queuing actions should be attached to the port-channel associated with this physical port."
Is there a way to get the auot-qos policies applied to the port-channel properly?
View 3 Replies
View Related
Apr 17, 2012
I have voice Bandwidth on Cisco Router 7200 and catalyst 3750.Now i want to sell some BW ( 15MB ) to any cleint. How to do that .We have Ethernet connectivity with my cleint.How i restrict client to 15MB. Will i have to form any VLAn or just port limit with bandwidth and which is better way?
View 8 Replies
View Related
Feb 1, 2012
What is the installation time for the Network Processor engine is:
NPE-G2=7200 series NPE-G2 engine with 3 GE/FE/E ports ,Do you reckon it can be done in two hours?
View 1 Replies
View Related
Mar 13, 2012
I have too much output drops in my cisco 7206 VxR NPE G1 router. I'm doing dot1Q on this interface and is connected to switch , i changed the router and IOS but still the error is same . What can be the reason . The interface on switch and router are 1000/Full and i changed the cable also . The traffic only comes about max70Mbps and it is really confusing. [code]
View 9 Replies
View Related
Dec 20, 2011
I have made some test and i noticed that qos input policy does not classify the icmp packet based on their dscp.The "match dscp ef" or "match precedence 5" is not working only the "match protocol icmp" shows hits.
We need to classify the different icmp packets based on dscp ( TOS ) for measurement purpose.CISCO 7200, 12.4.25d and 12.4.20T have a same behavior.
View 6 Replies
View Related
Jul 2, 2012
What are the rough figures that a NPE-G2 is able to hold for the BGP routing table?
378475 network entries using 51472600 bytes of memory 378482 path entries using 21194992 bytes of memory 63008/63003 BGP path/bestpath attribute entries using 8065024 bytes of memory BGP using 82975730 total bytes of memory
Are these 3 memories different memory allocated or are they are a sub-set of each other? If a NPE-G2 has 1GB RAM, does it mean that the routing table limit is depending on the RAM availability?
View 1 Replies
View Related
Jul 11, 2011
You got lots of bandwidth, expected throughput is low, and anticipated queuing/congestion is insignificant?My understanding is that QoS will kick in when there is congestion or queuing on an interface. Since an interface could either be 100% utilized or 0% utilized, is it fair to say that at any given point there could be congestion or delay on an interface?I know that the higher the interface speed, the lower the serialization delay will be, which means the lower the delay will be to put bits on the wire. For a 10Gig link, where the serialization delay is incredibly short, I imagine that even with occasional congestion, the delay would be insignificant and not affect VoIP traffic. Would this be true?
View 19 Replies
View Related
Nov 29, 2012
how to apply one command "wr" to all my Cisco Devices Managed by LMS 4.2?
View 2 Replies
View Related
Jul 28, 2011
I installed the Cisco LMS 4.0.1 (test mode), and monitoring services of the switches (data collection and information system) are working.
But when I need to apply some configuration via CiscoView settings are not applied.
The following message is displayed when I try to apply some configuration on an interface of any one switch.
"Message Timeout on 172.20.1.10. This error could be due to lack of access to the host, invalid SNMP credentials, or a busy device. To correct the problem, do one of the following:
- Verify access to the host.
- Check the SNMP credentials.
- Increase the timeout value through the preference options on the chassis view."
I've checked the credentials and SNMP communities, the problem continues.
View 1 Replies
View Related
Apr 17, 2007
I can not apply the LLQ to ADSL ATM interface. the system take the command with out any error message, but no in the show running config. Any Cisco link can explain this? [code]
View 2 Replies
View Related
Jun 12, 2012
I am trying to apply pach 5 to my ACS version 5.3 using FTP but i receive the following errors after issuing the show backup history command. When i use TFTP, i get a message saying that the file is too big, which i understand 164 MB.
after issuing the show repository "repository name", i get the following error.% Error reading directory on remote server.the patch is on one of my hard drives D, how do i specify on the ACS file path which drive to use?I can only place a url but without specifying which drive.
View 3 Replies
View Related
Feb 18, 2012
How can i apply password on tenda router?
View 1 Replies
View Related
Jun 30, 2010
How to configure SSH on a ASR 1002 and apply it to the Management Interface?
View 3 Replies
View Related
Sep 29, 2009
I am attempting to install a third party SSL cert (GoDaddy) to properly secure the external interface of my 1811 ISR so that I can implement SSL VPN. I have tried using SDM 2.5, but that doesn't appear to be working. I am familiar with doing this on a Cisco 3005 Concentrator, but I'm not aware of how to install an intermediate cert on the 1811 (or if it's even possible), in order to properly have the GoDaddy cert properly imported and used for SSL VPN. I have gone through the CSR process and have the initial cert from them generated and have imported it, but it never appears to be identified correctly if I browse to the external interface on the router. The router always defaults to its self-signed cert.
View 1 Replies
View Related
Apr 10, 2013
get a installed certificate work on a 5508 WLC Controller without rebooting. Is there a way? Is it possible to just reload a process to get the certificate work?
View 1 Replies
View Related
Dec 27, 2011
Is there any reason to apply qos to a 1.5 mbps connection. i had comcast with a 15 mbps connection and qos was good for when downloading large files and gaming and all that at the same time. but i have moved and i only can get dsl at 1.5 mbps.
View 10 Replies
View Related
Jun 4, 2013
we have a nat exemption rule for 10.0.0.0/8 to w.x.y.z followed by some static nat rules and then dynamic policy nat rule for 10.0.0.0/8 to w.x.y.z natting to IP a.b.c.d.When I do a packet trace from 10.10.10.10 to w.x.y.z, it shows the packet first matching against the nat exemption rule, and then immediately afterwards it matches the dynamic policy NAT rule. The static nat rules are being successfully bypassed (which is what I want), but why does the dynamic policy nat rule apply if an exempt rule has been hit already? An actual test between the IPs above reflects the result of the packet tracer as well (IP a.b.c.d is seen on server w.x.y.z).We are running the following software on an ASA5520.
View 7 Replies
View Related
Apr 29, 2012
We have a mix of 1231 and 1242 access points in an LWAPP environment. They are connected to WiSM controllers in our 6509's and are managed by a central WLC. Everything is running version 7.0.230. My question is can I apply MAC address filtering on a select group of AP's to restrict access to a specific SSID broadcast on these AP's without affecting other AP's also connected to the same WiSM?
View 3 Replies
View Related
Mar 24, 2011
I have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E duplex auto speed auto media-type rj45 service-policy output Metro-E?
View 1 Replies
View Related
May 1, 2013
I have a 3560G that I cannot apply a policy route-map to one of the VLAN interfaces. I am running up to date software, c3560-ipservicesk9-mz.150-2.SE2 and it accepts the command, but does not show it in the sh run of the interface. I updated to this code as I had seen previously someone said it needed to be version 15 before you could apply route-maps to VLAN interfaces.
View 4 Replies
View Related
May 19, 2011
Unfortunately it's not particularly obvious as the error that's thrown when trying to apply an IPv6 access-list to a DAP policy is pretty vague:
View 2 Replies
View Related