Is it safe to manage an 891 router across the Internet using Cisco Configuration Professional 2.4? If so, a few pointers on enabling and configuring it. If not, I assume setting up a VPN to the router then using CCP across the VPN would be the preferred approach.
View 1 RepliesI have a site to site vpn set up. I want to be able to manage the Cisco ASA router from a computer that connects to this site to site vpn. The problem is when I enter the ip address of the asa into adsm I get this error: Unable to launch device manager from 192.168.14.1:444. I am also unable to ping 192.168.14.1 from any computer that connects to the VPN, but I can ping other devices on the 192.168.14.x network. Also devices on the 192.168.14.x network can access the asa no problems. Here is my config:
ASA Version 8.2(1)
!
hostname Hostname
enable password POgOWyKyb0jgJ1Hm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
Within our small lan we have a core 3750, that handles our intervlan routing and is the core of the network. I recently looked into multicasting and set up a lab test with a 3550 with an EMI image and got the config to multicast to all vlans from one vlan, ready to go, at which point I found that our 3750 is IPBASE and doesn’t support multicasting. Currently upgrading the switch or image is not an option due to funding. My question is would it be possible and advisable to install our lab 3550 as a leg off the core, and in some way route multicasting traffic through that?I just cant get my head around the concept of having a core switch essentially routing all vlans, and then having another switch route the same vlan traffic again for multicasting to all the vlans again.
View 1 Replies View RelatedMay I know how to manage users using E1200... I've been trying to disable the internet to those intruder but I can't so I change my pword again and again.
View 3 Replies View RelatedI have the E3000 wired/wireless router and want to be able to manage my two SLM2008 switches with 192.168.1.253 and .254. Following the guides with adding vlan 2 and tagging the ports in which the two switches are wired together disables my ability to manage them seperately. I have added the gateway on 192.168.1.1 to both switches and told them that management vlan is 2 but no luck accessing them still.
View 1 Replies View RelatedHow can I get a E3000 or E4200 to manage more than 5 devices? Come on Cisco, lets get real. EVERYONE has more than 5 devices to manage. The average family of 4 has 3 or 4 computers, 4 smart phones and at least a couple of tablets and maybe some TV or game consoles. Setting access control policies is a must for anyone who is a parent.
Any good router that has a reasonable set of access control features? I've always loved Cisco up to this point, but I'm frustrated by this significant limitation.
link where to download user manual and/or Technical manual for Linksys RV042 Dual WAN VPN RouterDoes the Linksys RV042 Dual WAN VPN Router AGGREGATE the bandwidth of the two WAN Ports for LAN use or how does it operate?Does it manage traffic on Layer 7 (Application Layer);can i configure say, yahoo messenger traffic to take priority over youtube traffic or http traffic over download/upload traffic or such?Does it have DYNAMIC bandwidth allocation/management feature?Can i Guaranteed Bandwidth Allocation for a particular user or IP Address?Does it have TCP Ack Prioritization feature?Can i direct site(s) traffic,say cisco.com and/or port or service to use a particular WAN port?If this product cannot handle this features?
View 1 Replies View Related1. How I can manage those devices, the Switch and the router? What is the BEST SOLUTION to manage this devices?
2. I want to monitor the traffic on this environment, how I can do it? How I can monitor the traffic from customer A, Customer B, and my own LAN traffic, in terms of bandwidth that has passed throught my devices? Is it possible to monitor on MY LAN, or I have to monitor from the EXTERNAL switch?
3. How I can limit the bandwidth? I was trying to configure it using access list, with policy-map, etc....and limit this on each interface. [code]
The interface does not support the specified policy configuration and/or parameter values.Assigning a policy map to the output side of an interface not supported.With I few reading, I could see that the SWITCH 3750 doesnt support this configs.My INTERNET LINK is 30 Mbps, the ports on the Switch (WS-C3750X-48P-L) are Gigabit Ethernet.How I can limit the bandwidth here? For example, How I can limit a interface to 3Mbps..I was thinking about this:
- Limit the interface to 10Mbps: speed 10
- and limit the interface with 30% of this speed: srr-queue bandwidth limit 30
Does this work for both UPLOAD and DOWNLOAD?When the packets passes that 3Mbps limitation, will they be droped?
i'm trying to setup a local DNS server to manage small office local-only domain names for our servers. i have the DNS working properly (resolving local machines and using the ISP dns if it can't). so i put the DNS server ip into the "Static DNS 1" field of the router settings. the other 2 static dns fields are empty.the problem is that the router is still using the ISP dns server as the primary and my local dns server as the secondary. i verify this in two places. first, if i go to the "status" tab, DNS 1 shows the ISP server while DNS 2 shows my local DNS server. secondly, if i connect to the wireless device with a linux-based machine, the /etc/resolv.conf file shows the nameserver ips in the same incorrect order.
View 1 Replies View RelatedWe have just replaced a 4507R for a 4507R-E but I can't RME to manage it. I also can't get Cisco View to work. We appear to have packages installed (see attachments).
Is there anything I can do to troubleshoot?
I have setup WCS logins to be managed by ACS 4.2 . I was looking over the docs and I appear to be missing something because I can't find any documentation on doing the same to the controllers. I did successfully lock myself out of the WiSM in the lab during some testing. I had to pull the plug on the lab ACS to allow local login.
View 6 Replies View RelatedI was recently asked by a friend working for a new ISP in my city about managing their bandwidth, honestly I couldn't give him any answer.
View 6 Replies View RelatedIs-it possible to manage Cisco phone by web interface? (Manage transfertdiversion... of IP phone)When i go to http://ip_cisco7961 and i give permissions in settings of user (web Access: Enabled)I have only information in read only.
View 4 Replies View Relatedis it possible to manage a air-ap1262n with a controller like wlc 5500 or wlc 2500? the official cisco support could not answer me this question for sure. i have found this old guide to upgrade ap´s to lap´s, but there is hothing about the 1260 in it. [URL]
i am a little bit confused!
the cisco documents tells:
"at_a_glance_c45-636090.pdf"
A wireless network with standalone access points offers a low-cost, entry-level solution that does not require a controller. It is ideal for small-scale networks with less than 20 access points, and offers base-level wireless functionality with the flexibility to scale and add services over time by adding a controller.
I would like to as you that i have swiches 2960 (10Unit) and switches 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check performance.
View 3 Replies View RelatedSetting up SNMP on my Cisco AP's (1242AG Lightweight). How do I manage these via SNMP? It doesn't appear there is any settings within each AP for SNMP but only on the 4400 controller. What I am trying to do is setup Solarwinds Alerts, so when an AP goes down, I get notified of it. How or where this gets setup on the 4400 or the AP. I'm guessing there is something probably on the 4400 that I setup.
View 3 Replies View Relatedi have got 5 catalyst :
Cisco Catalyst WS-C2960G-24TS-S
version 12.2 (53) SE
Image : C2960S-UNIVERSALK9-M
and i can 't configure the switch with Cisco Network Assistant. I have got this error : "unsupported device".
it is not possible to configure this model with CNA ?
I have a dell powerconnect 3448 and am trying to find a good program to use to manage the switch.
View 7 Replies View RelatedI would like to know how I can split bandwidth between 4 work floors that have different needs. I have a network switch that can be managed (Cisco) but am not sure how I can set this up.
View 1 Replies View RelatedIm looking for tool that wud manage nsf files on network...
View 1 Replies View RelatedWe have a dir-615 in our ong.We would like giving different permission to the users.I want that users can connect only to the ong network and other user may use internet.Today i don't know hou to do. I can block intretrnet access (with child control), but not for only selected user.
View 1 Replies View RelatedI am new to the 4710 appliance.Apart from the 4 GE 'data' ports, there are 2 Ethernet 'management' ("console") ports. I find the description in the "quick start guide"somewhat confusing. URL, Is a first-time serial connection (at least to run the initial config. script) mandatory? Or can you obtain the same result via one of the 2 Ethernet management ports and using a default ip address (192.168.1.10 ? When running the initial config. script (only possible from the serially connected console i suppose), you have to select your management port. Why does the system in step 5 proposes you 4 ports, and not just 2? I suppose the intended port for management is one of the 2 management ports, not one of the 4 data ports?
View 1 Replies View RelatedI've created a DMZ on ASA5510, it can access anything internal but cannot get out to internet. I cannot manage the ASA from the DMZ subnet neither.
View 6 Replies View RelatedWe have 6500 chassises in our set up. But using CWLMS 4.0 , we are unable to manage VSS feature of 6500.Also User tracking for Nexus 7K Switches subnets are not working.
View 1 Replies View RelatedI have only one LAP-1142N-E-K9. It is controller based AP but i dont have WLC. I want to manage these AP with a HP Switch. (HP 1910-24G-PoE)
But i dont known that a LAP-1142 is competible? If yes, how can i manage or configure these LAP with HP switch?
I have a known working configuration with many sites and one operative center that receives all communications.The connection OF THE OLD SITE is here detailed:Now I need to integrate another site. The difference between the old site and the new site is the following:
-old site communicates with the operative center by means of the FE0/1 or by means of an HWIC4T serial interface.
old site automatically switches between the tunnel on the ethernet interface (FE0/1) and the serial channel giving priority to the ethernet tunnel.
-new site will communicate with the operative center by means of the FE0/1 or by means of a transceiver device connected on the FE0/0.
-both new site and old site have a LAN on the FE0/0 where data is generated and sent to the router to be dispached to the best available channel.
The connection of THE NEW SITE is here detailed: the old site was configured this way: [code]
the first line means that everything starting from the client directed to 192.169.0.2 it will be sent on the tunnel1.the second line tries to route the same packets on serial0/0/0 with low priority.On the New site i did the same:
i created the tunnel form my cisco 2811 to the operative center using the FE0/1, then i added the following:ip route 192.169.0.2 255.255.255.255 Tunnel1
This works as expected routing the packets to the operative center on the FE0/1.Now I miss the second part: route packets on the FE0/0 to the ip address 192.168.1.31 WITH LOW PRIORITY like i did on the old site.
I did some tries but no one solves. Which is, in your opinion, the right command to add on the cisco2811 in order to get the equivalent of what i did on the old site ( ip route 192.169.0.2 255.255.255.255 Serial0/0/0 10 ) ?
Does DCNM (DCNM-N7K-K9) ver 5.2 on Nexus 7k manage nexus 5k??
View 2 Replies View RelatedNow i plan to order Wireless Cisco model : AIR-AP1242AG-A-K9 around 40 unit but i don't know to manage all AP becuase it has alot of AP,
View 9 Replies View Relatedi have range 200 meter how i manage my connection..
View 1 Replies View RelatedI have a Linksys WRT54GS wireless router. I was trying to get into the set up (using the IP listed in here [URL]) and it asked for a username and password. I have what I thought was the password but no idea what the username was. I tried Administrator and what I had written down as the password but nada. This was originally set up 9 years ago and 3 pc's ago.On the bottom of the router is listed Ownership ID, Device ID, and a serial numb.
View 2 Replies View RelatedAs DCS-942L IP cam is compatible with "NVSCGI APIs" (search this string on a search engine and you will find some useful PDF docs), many features of this IP Cam may be enabled or disabled using any web browsers, for example we can manage the motion detect.
[url]....
I have a 20MB internet connection, with a 100GB cap. My mother works at home, with some employees. Adding home and work, 8 people use the internet all the time. Lots of Youtube videos, streaming netflix, iTunes downloading, and so on.I wanted something to:
1) Manage this cap. It's over too soon, and we're left with a poor internet connection until the end of the month - like 500kb.
2) Something to manage two internet connections.
I was thinking about a dedicated router - I currently use a WRT54G V8, which is nice, but it has some issues handling the traffic when the internet is in its full glory. I heard about pfSense, and some searches on Google tell me it's possible to do both options using it.
I have Cisco L3 3560G switch which directly connected with router . i have configured Vlan 2,3 on the switch and assign port 2 & 3 respectably. I want to management both vlan 2 & 3 from from L3 port g0/10 .
View 6 Replies View Related