Is-it possible to manage Cisco phone by web interface? (Manage transfertdiversion... of IP phone)When i go to http://ip_cisco7961 and i give permissions in settings of user (web Access: Enabled)I have only information in read only.
View 4 RepliesI was deploy new site-to-site between ASA 8.0 (HQ) and ASA 8.4 (Branch). Everything working fine but i have a problem about manage to the remote ASA that i can't manage ASA branch with Inside interface IP address.My configuration on Remote ASA
management-access inside
icmp permit any inside
ssh 0.0.0.0 0.0.0.0 inside
snmp-server host INSIDE 10.0.1.101 communitry test-snmp version 2c
My Test
- ping from HQ to inside interface of remote ASA Client show request timeoutWhen debug icmp on remote ASA then ASA show only ICMP request from HQ no reply back from remote ASA I'm not sure this is bug on ASA 8.4 or not because i can manage another remote ASA which software version 8.0 from HQ?
Is it safe to manage an 891 router across the Internet using Cisco Configuration Professional 2.4? If so, a few pointers on enabling and configuring it. If not, I assume setting up a VPN to the router then using CCP across the VPN would be the preferred approach.
View 1 Replies View RelatedWe have just replaced a 4507R for a 4507R-E but I can't RME to manage it. I also can't get Cisco View to work. We appear to have packages installed (see attachments).
Is there anything I can do to troubleshoot?
I have setup WCS logins to be managed by ACS 4.2 . I was looking over the docs and I appear to be missing something because I can't find any documentation on doing the same to the controllers. I did successfully lock myself out of the WiSM in the lab during some testing. I had to pull the plug on the lab ACS to allow local login.
View 6 Replies View RelatedI was recently asked by a friend working for a new ISP in my city about managing their bandwidth, honestly I couldn't give him any answer.
View 6 Replies View Relatedis it possible to manage a air-ap1262n with a controller like wlc 5500 or wlc 2500? the official cisco support could not answer me this question for sure. i have found this old guide to upgrade ap´s to lap´s, but there is hothing about the 1260 in it. [URL]
i am a little bit confused!
the cisco documents tells:
"at_a_glance_c45-636090.pdf"
A wireless network with standalone access points offers a low-cost, entry-level solution that does not require a controller. It is ideal for small-scale networks with less than 20 access points, and offers base-level wireless functionality with the flexibility to scale and add services over time by adding a controller.
I would like to as you that i have swiches 2960 (10Unit) and switches 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check performance.
View 3 Replies View RelatedSetting up SNMP on my Cisco AP's (1242AG Lightweight). How do I manage these via SNMP? It doesn't appear there is any settings within each AP for SNMP but only on the 4400 controller. What I am trying to do is setup Solarwinds Alerts, so when an AP goes down, I get notified of it. How or where this gets setup on the 4400 or the AP. I'm guessing there is something probably on the 4400 that I setup.
View 3 Replies View Relatedi have got 5 catalyst :
Cisco Catalyst WS-C2960G-24TS-S
version 12.2 (53) SE
Image : C2960S-UNIVERSALK9-M
and i can 't configure the switch with Cisco Network Assistant. I have got this error : "unsupported device".
it is not possible to configure this model with CNA ?
I have a dell powerconnect 3448 and am trying to find a good program to use to manage the switch.
View 7 Replies View RelatedI would like to know how I can split bandwidth between 4 work floors that have different needs. I have a network switch that can be managed (Cisco) but am not sure how I can set this up.
View 1 Replies View RelatedIm looking for tool that wud manage nsf files on network...
View 1 Replies View RelatedWe have a dir-615 in our ong.We would like giving different permission to the users.I want that users can connect only to the ong network and other user may use internet.Today i don't know hou to do. I can block intretrnet access (with child control), but not for only selected user.
View 1 Replies View RelatedI am new to the 4710 appliance.Apart from the 4 GE 'data' ports, there are 2 Ethernet 'management' ("console") ports. I find the description in the "quick start guide"somewhat confusing. URL, Is a first-time serial connection (at least to run the initial config. script) mandatory? Or can you obtain the same result via one of the 2 Ethernet management ports and using a default ip address (192.168.1.10 ? When running the initial config. script (only possible from the serially connected console i suppose), you have to select your management port. Why does the system in step 5 proposes you 4 ports, and not just 2? I suppose the intended port for management is one of the 2 management ports, not one of the 4 data ports?
View 1 Replies View RelatedI've created a DMZ on ASA5510, it can access anything internal but cannot get out to internet. I cannot manage the ASA from the DMZ subnet neither.
View 6 Replies View RelatedWe have 6500 chassises in our set up. But using CWLMS 4.0 , we are unable to manage VSS feature of 6500.Also User tracking for Nexus 7K Switches subnets are not working.
View 1 Replies View RelatedI have only one LAP-1142N-E-K9. It is controller based AP but i dont have WLC. I want to manage these AP with a HP Switch. (HP 1910-24G-PoE)
But i dont known that a LAP-1142 is competible? If yes, how can i manage or configure these LAP with HP switch?
I have a known working configuration with many sites and one operative center that receives all communications.The connection OF THE OLD SITE is here detailed:Now I need to integrate another site. The difference between the old site and the new site is the following:
-old site communicates with the operative center by means of the FE0/1 or by means of an HWIC4T serial interface.
old site automatically switches between the tunnel on the ethernet interface (FE0/1) and the serial channel giving priority to the ethernet tunnel.
-new site will communicate with the operative center by means of the FE0/1 or by means of a transceiver device connected on the FE0/0.
-both new site and old site have a LAN on the FE0/0 where data is generated and sent to the router to be dispached to the best available channel.
The connection of THE NEW SITE is here detailed: the old site was configured this way: [code]
the first line means that everything starting from the client directed to 192.169.0.2 it will be sent on the tunnel1.the second line tries to route the same packets on serial0/0/0 with low priority.On the New site i did the same:
i created the tunnel form my cisco 2811 to the operative center using the FE0/1, then i added the following:ip route 192.169.0.2 255.255.255.255 Tunnel1
This works as expected routing the packets to the operative center on the FE0/1.Now I miss the second part: route packets on the FE0/0 to the ip address 192.168.1.31 WITH LOW PRIORITY like i did on the old site.
I did some tries but no one solves. Which is, in your opinion, the right command to add on the cisco2811 in order to get the equivalent of what i did on the old site ( ip route 192.169.0.2 255.255.255.255 Serial0/0/0 10 ) ?
Does DCNM (DCNM-N7K-K9) ver 5.2 on Nexus 7k manage nexus 5k??
View 2 Replies View RelatedNow i plan to order Wireless Cisco model : AIR-AP1242AG-A-K9 around 40 unit but i don't know to manage all AP becuase it has alot of AP,
View 9 Replies View Relatedi have range 200 meter how i manage my connection..
View 1 Replies View RelatedI have a Linksys WRT54GS wireless router. I was trying to get into the set up (using the IP listed in here [URL]) and it asked for a username and password. I have what I thought was the password but no idea what the username was. I tried Administrator and what I had written down as the password but nada. This was originally set up 9 years ago and 3 pc's ago.On the bottom of the router is listed Ownership ID, Device ID, and a serial numb.
View 2 Replies View RelatedAs DCS-942L IP cam is compatible with "NVSCGI APIs" (search this string on a search engine and you will find some useful PDF docs), many features of this IP Cam may be enabled or disabled using any web browsers, for example we can manage the motion detect.
[url]....
I have a 20MB internet connection, with a 100GB cap. My mother works at home, with some employees. Adding home and work, 8 people use the internet all the time. Lots of Youtube videos, streaming netflix, iTunes downloading, and so on.I wanted something to:
1) Manage this cap. It's over too soon, and we're left with a poor internet connection until the end of the month - like 500kb.
2) Something to manage two internet connections.
I was thinking about a dedicated router - I currently use a WRT54G V8, which is nice, but it has some issues handling the traffic when the internet is in its full glory. I heard about pfSense, and some searches on Google tell me it's possible to do both options using it.
I have Cisco L3 3560G switch which directly connected with router . i have configured Vlan 2,3 on the switch and assign port 2 & 3 respectably. I want to management both vlan 2 & 3 from from L3 port g0/10 .
View 6 Replies View RelatedMgmt Vlan 1 (default) Data VLan 10 (with access to internet) Is there a way to have a PC attached to a SG300 switch such that it can both access Vlan 10 for data and Vlan 1 for managment ? The PC's port clearly needs to be untagged PVID on vlan 10. I have tried adding vlan 1T and setting the port as a trunk port but to no avail, The switch is currently level 2. I am guessing this might not be possible in level 2 without setting the mgmt vlan to 10 ?.
View 3 Replies View RelatedWe are trying to manage our Cisco ASA 5520 (8.2.5) SSL clients through Active Directory(ldap).
Currently the SSL VPN tunnel is up and all users are able to connect being authenticated by AD. but Group-policy to AD groups are not working. all the domain users are able to go to all the group policies .
I need to give access only to their respective Group policy in ASA. Following are the available groups and GP.
Code...
We have the following proplem with the RV 120w router with the last firmware. We can't manage to set up port forwarding. So the situation is like this: we have WAN ip: 192.168.2.68 and our router connects to VPN server and gets an IP like 10.0.10.X. In the inner network we have PCs and a DVR (digital video recorder) with ip 192.168.1.215. Our DVR uses 3 main ports like 81 (http) and 37777 (tcp), 37778 (udp) and we try to make port forwarding with the router interface like the manual says (look and the sceenshot). But when we try to enter our DVR and see the picture from the outside network (we type in browser 192.168.2.68:81) nothing happends. It just dosen't work.
Before cisco we used d-link router and everything worked just fine with the same port forwarding rules.So we need to enter WAN address in Cisco and show the 81 port in the address bar and see the picture from the DVR 192.168.1.215 from the inner network.
I have a site to site vpn set up. I want to be able to manage the Cisco ASA router from a computer that connects to this site to site vpn. The problem is when I enter the ip address of the asa into adsm I get this error: Unable to launch device manager from 192.168.14.1:444. I am also unable to ping 192.168.14.1 from any computer that connects to the VPN, but I can ping other devices on the 192.168.14.x network. Also devices on the 192.168.14.x network can access the asa no problems. Here is my config:
ASA Version 8.2(1)
!
hostname Hostname
enable password POgOWyKyb0jgJ1Hm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
I want to use Cisco VPN Client to VPN to my SA520 to manage a UC320W. I can establish a VPN connection to the SA and ping both the SA and a switch that I have on the network, but I cannot ping my UC. I've set up firewall rules to allow ANY-ANY access from LAN-WAN, and a WAN-LAN rule to allow a certain range of IP addresses (the IP addresses assigned from the VPN DHCP pool, in this case, 192.168.12.x) access to the UC.
My SA IP address is 192.168.75.1 and my UC is 192.168.75.2 (I can ping both when I am directly connected to a LAN port on either equipment).
So what we do when we get new laptops, we "prime" it by connecting to the lan via a cable, name the machine and join the domain. This way it automatically gets the certificate and is a domain member. After logging on at least once via a cable, we can then disconnect it and join the wireless network.
During a routine audit, they suggest also using MAC address filtering. I think this is overkill and an administrative nightmare. To manage MAC address filtering on the 5508 and then also manage the domain accounts is unnecessary. Also down the road we want to offer a segregated public hotspot (webauth), and I'm not sure if MAC address filtering would affect that or not.
I've read that MAC address filtering is pretty much useless, because it's so easy to change your mac address even in Windows device manager. I know I was able to do it as a test.
is MAC address filtering worth the hassle to implement and manage? Or is our current layered security approach enough?
I have an older RV016 that has been running 3.0.0.19-tm. Yesterday I tried to upgrade the firmware to 4.0.3.03-tm, but the operation timed out. After an hour or so my browser still displayed "page cannot be displayed". When I navigated back to the main screen, it still showed 3.0.0.19-tm.
I supposed I should have quit while I was ahead, but then I loaded the 3.0.2.01-tm firmware. This was successful. However, I was getting SSL certificate errors (not from a trusted authority), so I turned off SSL in the router options.
Now I cannot connect to the router via http or https. I can connect via telnet. Is there a way to re-enable SSL from the command line? Or is there another way to restore web management short of doing a factory reset? (I have several VPN connections that would be painful to recreate.)